再退火

The surface treatment was aqua regia boiling before metallization and annealing after metallization at different conditions in N2 ambient.

在制作金属电极前用煮沸王水对样片进行表面预处理，金属制作后再在N2氛围中做快速热退火处理。

Eachcycle consisted of 45 sec. at 94℃ to denature, 45 sec. at 36℃ for theannealing primer, and 120 sec. at 72℃ for extension. The otherreactions were completed under 10 min. of extension at 72℃.

扩增反应在热循环仪上完成，程序设置为94℃变性处理45秒钟，36℃引物退火45秒种，72℃链延伸2分钟，依此作45个循环，然后再在72℃条件下使被扩增的链延坤10分钟完成全部反应。

We will utilize tabu search and simulated annealing to determine the discrete decisions. Then, by using the discrete decisions, a mathematical programming model, proposed herein, will be used to solve the continuous decisions.

求解方法为先利用塔布搜寻法或模拟退火法找出离散决策，再带入一个以最小化总存货成本为目标的数学规划模式，以求解出连续决策的值与目标函数值。

Nanoporous gold with different pore sizes was prepared by controlling the etching time of Au/Ag alloy with concentrated nitric acid and annealing. Scanning electron microscopy and a nitrogen adsorption technique were used to characterize the NPG.

以Au/Ag合金为原料，通过控制浓硝酸的腐蚀时间再辅以退火处理得到了不同孔径的纳米多孔金，利用扫描电镜和N2气体吸附仪对孔性质进行了表征。

In the algorithm, a three-dimensional permute matrix of binary variables is used to map the problem to the neural network, the energy function including object item, overlap constrained item and timing constrained item is presented, and then iteration procedure is put into practice with the mean annealing equations.

算法用一个三维二值换位矩阵将问题映射为神经网络，建立包含时延约束、重叠约束和优化目标的能量函数，再用均场退火方程迭代求解。

In the algorithm,with a three-dimensional permute matrix of binary variablesubeing used to map the problem to the neural network,the energy function including object item,overlap constrained item and timing constrained item,is presented,and then iteration procedure is put into practice with the mean annealing equation.

算法用一个三维二值换位矩阵将问题映射为神经网络，建立包含时延约束、重叠约束和优化目标的能量函数，再用均场退火方程迭代求解。

The precursive Fe3O4 films were sulfurized using constant current electrodepositing and oxidation treating, and Fe3O4 films was transformed into FeS2 thin films after heat sulfur annealing of 400℃ at different sulfurizing pressures.

采用恒流电沉积及氧化处理制备Fe3O4先驱体薄膜，再通过400℃下的热硫化退火，使Fe3O4先驱体薄膜在不同硫压下转变成为多晶FeS2薄膜。

The influence of continuous annealing on the properties and recrystallization texture of Nb-Ti- IF steel was studied.

研究了热镀锌连续退火工艺对Nb-Ti-IF钢性能及再结晶织构的影响。

The experimental results show that recrystallization of deformed ferrite is strongly influenced by heating rate and occurs mainly between 600℃ and 720℃.

实验表明，在连续退火初期的加热过程中，在600~720℃大量进行再结晶。

The results show that dynamic softening is easy to occur in these ingots and flow stress becomes steady finally; the material constants of hot deformation are procedural parameters that stress-level coefficient α, strain rate sensibility exponent m and deformation activation energy Q are all increased with strain increasing, while stress exponent n is decreased gradually; the values α and m of the alloy homogenized are the biggest and the value n is the smallest, dynamic softening effect of the alloy is the most obvious, which can deform evenly; influence of strain on the value Q of the alloy homogenized is a little and the average value of Q is only 176.5kJ/mol, so the alloy is easy to deform; the alloy matrix shows the regular recrystallization grains when the strain is 50%; dislocation cell structure re-formed in the grains with increase of strain.

结果表明：经不同处理的Al-1Mn-1Mg合金均易发生动态软化并最终呈现稳态流变特征；热变形材料常数是过程量，随应变量的增加，应力水平参数α、应变速率敏感性指数m和热变形激活能 Q 随之增大，而应力指数 n 则逐渐减小；均匀化退火后，铝合金的α和m值最大而n值最小，动态软化效果最明显且变形均匀，在该状态下，铝合金的 Q 值受变形量影响小，平均仅为176.5kJ/mol，易进行热变形；当应变量为0.7时，基体呈现规则的再结晶晶粒组织，随着应变量的增加，晶内重新形成了位错胞结构。

With Death guitarist Schuldiner adopting vocal duties, the band made a major impact on the scene.

随着死亡的吉他手Schuldiner接受主唱的职务，乐队在现实中树立了重要的影响。

But he could still end up breakfasting on Swiss-government issue muesli because all six are accused of nicking around 45 million pounds they should have paid to FIFA.

不过他最后仍有可能沦为瑞士政府&议事餐桌&上的一道早餐，因为这所有六个人都被指控把本应支付给国际足联的大约4500万英镑骗了个精光。