再计算

A comparative study of the flux vector splitting techniques and the flux difference technique with different entropy fix formula is presented with regards to their ability to accurately predict the heat transfer rate on the surface of blunt body.

本文采用计算效率较高的标量对角化隐式NND格式，通过求解Navier Stokes方程对影响再入体表面热流计算准确的诸因素进行了综合分析。

On the basis of freeboard phenomenon in curve way and the improvement of curve flow velocity, this paper gets a useful calculating method of bed roughness.

这些公式均涉及到沟床糙率的计算。关于泥石流沟床糙率的研究，主要根据水力学上的研究，再加以变化而来。目前，在水力学中沟床糙率的计算方法主要有水力学方法、查表粗估法、糙率公式计算法[2]。

First the FEM-BI (Finite Element – Boundary Integral Methods) base on vector element is presented to compute the electric field in the cavity backed antennas.

计算中首先采用基于矢量单元的"有限元－边界积分方程法"计算出背腔天线内部电场的分布；再采用互易原理求解天线的远区场，从而获得天线的辐射方向图。

Three elements should be calculated in first-order circuit, which can synthesise analytical solution. Second-order series RLC and parallel RLC both can be calculated by the general function, which uses the Matlab to calculate differential equations. Generally, second-order and high-order circuits use Laplace transformation to formulate circuit equation, and get analytical solution by using Laplace inverse transform.

一阶电路先计算3要素，后合成解析结果；RLC串联和并联的二阶电路采用自编的通用函数计算，自编函数采用了Matlab求解微分方程的符号运算方法；一般的二阶电路和高阶电路采用拉氏变换列写电路方程，再用拉氏反变换得到解析结果。

Then, the boundary points are extracted. By using Shu's theorems the sum of Legendre polynomial of the boundary points is calculated.

首先使用Yang-离散格林公式将二值图像矩计算中区域内求和转换为沿区域边界求和；然后提取该图像的边界点；再利用Shu提出的公式计算出边界点的Legendre多项式的叠加值。

Based on the traits of the aspherical lens, the sunlight was focused on a very small spot, and then it was transferred into a plastic fiber by an aspherical lens and a selfoc lens. A formula for calculating the optimal length of selfoc lens is presented. The optimal assembly of the aspherical lens and selfoc lens was implemented by the aid of this formula. Therefore, sunlight is coupled into a plastic fiber efficiently.

根据非球面透镜垂轴球差小的特点把太阳光会聚到很小的光点，再利用长度约为1/4节距的自聚焦透镜改变光线的数值孔径使其满足光纤的数值孔径，通过一个计算公式来计算最佳的自聚焦透镜长度，实现非球面透镜和自聚焦透镜的最佳组合，把太阳光以较高的耦合效率耦合进塑料光纤。

Finally, according to voltage with compute the electric current choose once equipments, including circuit breaker, insulate the switch, fuse, voltage transformer, current transformer, lightning arrester, busbar and electric cable and so on, then according to compute the result of the short-circuit electric current with designs the request to once equipments proceed check to break the ability of flowing and stable degrees of short circuit about moving and hot.

最后，根据电压和计算电流选择一次设备，包括断路器、隔离开关、熔断器、电压互感器、电流互感器、避雷器、母线和电缆等，再根据短路电流计算结果和设计要求对一次设备进行断流能力和短路动稳定度、热稳定度的校验。

In order to calculation Lyapunov exponent spectrum of unknown system,firstly,reconstruct phase space of observed one-dimensional time series,secondly,use Least-Squared Support Vector Machine approximate dynamical equation of reconstruction system and calculation Lyapunov exponent spectrum by Jacobian matrix.

为了计算未知系统的Lyapunov指数谱，首先，对一维观测数据序列进行相空间重构，然后，利用最小二乘支持向量机逼近重构系统的动力学方程，再通过雅克比矩阵计算Lyapunov指数谱。

The modified method can satisfy the limit of mean square deviation within 10W/m^2, and the average relative error is about 25%.

计算结果与西沙实测资料、长年代的GSSTF2资料和NCEP/NCAR再分析资料进行比较验证，证明改进后的方法精度较高，基本可以保证湍流热通量的平均标准偏差在10W/平方公尺左右，与多年的月平均做比较，相对偏差为25%左右；同时，不仅首次将计算热通量的空间尺度精确到0.1°×0.1°，而且基本模拟出了南海季风暴发期间热通量变化的主要特点以及中国近海热通量随季节、纬度和海岸地形的变化特征。

This method corrected the Wien approximate based on the mathematical principle, and calculated the spectral shape using ADE to identify the band which had the maximum and minimum emissivity, then deduced the relationship of each band's emissivity after the correction of Wien approximate and derived the actual emissivity using this relationship and MMD model.

对维恩近似从基本原理上进行修正，利用ADE计算光谱大致形状以确定发射率最大最小的波段，推导出了在修正维恩近似后各个波段发射率的关系，再利用这个关系以及最大最小值差模型计算实际的发射率。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。