再处理

The revascularization of ACL following RF treatment originates from the synovial membrane to the RF-penetrated parts. The repair of the amph-portions is better than that of the midportion, which indicates that the optimal parts for exercising RF reefing on is the amph-portions of ligament.

射频处理后前交叉韧带的再血管化模式是由滑膜向韧带射频渗透区域进行的，韧带两端组织的修复优于韧带的中间部分，提示射频紧缩的最佳部位为韧带两端。

If want the data of built-in in HTML page of the static state trends, and these dynamic data are the word that will offer by the program such as ASP, PHP, so every time a person visits your website, the server is about to carry out and handle Tongji.asp document, from the data with draw-out and relevant database, reexport shows to the webpage, if tens of thousands of person is visited at the same time, be about to be carried out tens of thousands of times, consequence cans be imagined.

假如要在静态的HTML页面里嵌入动态的数据，而这些动态的数据是由ASP、PHP等程序来提供的话，这样每次有一个人访问你的网站，服务器就要执行并处理一次tongji.asp文件，从数据库抽取相应的数据，再输出给网页显示，假如有几万个人同时访问，就要执行几万次，后果就可想而知。

The results show that dynamic softening is easy to occur in these ingots and flow stress becomes steady finally; the material constants of hot deformation are procedural parameters that stress-level coefficient α, strain rate sensibility exponent m and deformation activation energy Q are all increased with strain increasing, while stress exponent n is decreased gradually; the values α and m of the alloy homogenized are the biggest and the value n is the smallest, dynamic softening effect of the alloy is the most obvious, which can deform evenly; influence of strain on the value Q of the alloy homogenized is a little and the average value of Q is only 176.5kJ/mol, so the alloy is easy to deform; the alloy matrix shows the regular recrystallization grains when the strain is 50%; dislocation cell structure re-formed in the grains with increase of strain.

结果表明：经不同处理的Al-1Mn-1Mg合金均易发生动态软化并最终呈现稳态流变特征；热变形材料常数是过程量，随应变量的增加，应力水平参数α、应变速率敏感性指数m和热变形激活能 Q 随之增大，而应力指数 n 则逐渐减小；均匀化退火后，铝合金的α和m值最大而n值最小，动态软化效果最明显且变形均匀，在该状态下，铝合金的 Q 值受变形量影响小，平均仅为176.5kJ/mol，易进行热变形；当应变量为0.7时，基体呈现规则的再结晶晶粒组织，随着应变量的增加，晶内重新形成了位错胞结构。

Reheat is a popular approach of air handling process.

再热是空调系统中常采用的空气处理方式。

Reimplantation after vitrectomy is an effective method for management of the posterior chamber IOL dislocation.

前段玻璃体切除单纯取出再植入，是处理后房型人工晶状体脱位简单有效的方法。

Methods The causes and managements of posterior chamber IOL dislocation in 23 eyes were analyzed. The managements included pupillary dilatation with 1% tropicamide, replacement, operative reduction, reimplantation after vitrectomy and removement of IOLs.

对23例23眼后房型人工晶状体脱位的原因进行分析；采用托吡卡胺散瞳复位、单纯手术复位、前段玻璃体切除单纯取出再植入、更换和取出人工晶状体等方法进行处理。

With the two patches on screen, select one of them, make sure that they are 0 to # of spans, else export them to DXF and reimport them, use the following MEL command

屏幕中保留两个你要处理的面片，选择其中一个，确定他们是 0 to #个跨度（0 to # of spans），不然就将他们导入 DXF 格式，再导回来，然后使用下面这个MEL命令。

Also the stability under the magnetic field impact was relative to remanence and other magnetic properties

晶化处理后，低温出炉或长时间保温后再出炉对获得性能稳定的磁芯较为有利。

An experimental investigation on the Physicochemical characteristic of Ni-base superalloy remelt layer generated by laser drilling or electro-discharge machining is described in the paper.

研究了镍基超合金激光/电火花打孔再铸层的物理化学特性，并报道了DZ125、ЖC6y、K24、DD3、DD6以及IC10等合金的化学研磨处理对基材腐蚀及其力学性能与热疲劳性能的影响等。

In carrying out this principle, the market and government are in allocate and respective effect should be produced better in repartition the first time, make efficiency and fair relation get very good processing, harmony of farther stimulative society develops.

在执行这个原则中，市场和政府在初次分配和再分配中应更好地发挥各自的作用，使效率与公平关系得到很好的处理，进一步促进社会和谐发展。

By the time of its fall, most of the prisoners were writers who had written against the corruptions of the government.

到它被攻陷的时候，里面多数的犯人是写了反对政府贪污文章的作家。

The most obvious variation to ovum morphological character was that the color was changed from light green to sepiaceous in embryonic development, and all the ovums were almost hatched after 96h.

在胚胎发育过程中卵的形态特征最明显的变化是颜色从淡绿到深褐色，卵在发育96h后卵基本全部孵化。