再处理

Methods Rats were randomly divided into control group, ischemia-reperfusion group and ischemic preconditioning group.

将大鼠随机分为对照组、缺血再灌注组和缺血预处理后缺血再灌注组。

Methods Rats were randomly divided into control group,ischemiareperfusion group and ischemic preconditioning group.

将大鼠随机分为对照组、缺血再灌注组和缺血预处理后缺血再灌注组。

Methods: 18 healthy new-zealand rabbits were randomly divided into 3 groups (6 for each group): ischemic reperfusion group,ischemic preconditioning group and ischemic preconditioning combined with pyrrolidine dithiocarbamata group (group IPC+PDTC).

选择健康新西兰大白兔18只，随机分为缺血再灌注组(ischemic reperfusion， IR)，缺血预处理组(ischemic preconditioning ，IPC)及缺血预处理联合PDTC组，每组6只。

this paper introduces a lossless detected circuit system.firstly,system gathers slender infrared signal with transducer,then amplifies them with low noise.through voltage comparator circuit,transforming simulation objection signals to digital signals.finally,transforming transport landscape orientation and portrait to single chip processing.in design of pcb,the amplifying of quadruplet signal,filter,voltage comparator decree and and logic function are manufactured in one board.if the diameter of workpiece is long,it can add multiple the number of transducer of four,to wide its range of practice,disposing circuit only need one module.

摘 要：介绍了一种无损检测的电路系统。系统首先利用传感器采集到微弱的缺陷信号，再将缺陷信号进行低噪声放大，然后通过电压比较判决电路将模拟缺陷信号变换成数字信号，最终将横、纵两路的输出信号送至单片机处理。在pcb设计中，将四路信号的放大、滤波、电压判决以及与逻辑功能做在一块板上，若被检测工件的直径较大，可以将传感器的个数以四的倍数增加，处理电路只需增加一个模块。

Therefore, development, destruction, treatment, re-development, and then destroyed, re-treatment, continue to play.

因此，发展，销毁，处理，再发展，然后销毁，重新处理，继续发挥。

Results showed that green firm callus and rooting were obtained with treatments of NAA 0.5-3.0mg/L, in which the NAA 0.5mg/L treatment appeared the optimal rooting result of 90%. White loose callus was obtained with treatment of 2,4-D0.1-3.0 mg/L.Callus can not be induced by adding BA solely at 0.5-3.0mg/L. There appeared bud redifferentiation only when appropriate concentration of combined BA,NAA and 2,4-D were applied.

结果表明：单独加入NAA0.5～3.0mg／L可诱导出绿色致密的愈伤组织，并再生出根，其中NAA0.5mg／L处理生根率最高，达90％；单独加入2，4-D0.1-3.0mg／L可诱导出白色疏松的愈伤组织；单独使用BA0.5—3.0mg／L不能诱导出愈伤组织；BA与NAA或2，4-D只有在适当的质量浓度范围内配合使用才能分化出芽，芽分化率最高的处理为BA3.0mg／L＋NAA0.5mg／L，分化率为30％。

The bioceramic coating was made by Lasser remelt pretreating a layer of mixed powder CaHPO 4·2H 2O CaCO 3 Y 2O 3 on the TC 4 substrate.

在激光表面重溶预处理的TC4合金基材上预置涂敷CaHPO42H2O－CaCO3－Y2O3混合粉末，再经激光熔覆处理制备了生物陶瓷复合涂层。

The system utilized four laser scanners along lengthwise direction of the log. Data are obtained in every ten degrees when log is turning, in each cross section, 36 data are obtained. Then the data obtained were processed and an outline of the cross section of the log was developed on computer screen. Afterwards, the largest inscribed circles for log cross sections were determined according to the principle that three points can determine a circle. Secondly, the points located on the cross sections were linked up along some log generative in order to simulate the three-dimension log outline. At last the largest right circular cylinder were optimized and the optimum turning center was determined by means of projective theory.

具体作法是：在木段长度方向均匀设置四个激光传感器，当木段旋转时，起动激光传感器，进行数据采集，每隔10~0扫描一个点，在各横断面圆周上共采集36个点的数据，由计算机处理采集的数据，并绘制出原木横断面的几何图形，再根据三点定圆的原理，确定出最大内接圆；其次，模拟原木三维廓形，即将原木相邻横断面上离散点沿着母线方向连线，由计算机分析处理，绘制原木三维廓形；最后，采用投影法，优化出原木最大内接圆柱体，并确定原木回转中心线。

The products are factory sanded and finished with a layer of clear satin protective coating.

本产品在工厂中经过砂磨处理后，再用一层光亮的防护涂料做表面处理。

Analogtodigital converter is very important in digital signal process board,so calculation of the effective numbers of bits is of great importance for evaluation of system performance.

将模拟信号转换为数字信号后再进行处理，是当前信号处理普遍使用的方法，模数转换器就是将模拟信号转换为数字信号的器件，所以计算其有效转换位数对系统性能评估就显得尤为重要。

For a big chunk of credit-card losses; the number of filings (and thus charge-off rates) would be rising again, whether

年美国个人破产法的一个改动使得破产登记急速下降，而后引起了信用卡大规模的亏损。

Eph. 4:23 And that you be renewed in the spirit of your mind

弗四23 而在你们心思的灵里得以更新