内轴

In the end, stress distribution at the connection position and distribution of contact pressure on the thread teeth are deduced by applying equivalent contact pressure.

通过变形协调原理，求出了轴向力沿接头螺纹牙的大小分布，进而求出了上扣、内压和拉伸工况综合作用下的等效接触压力。

Reversible high temperature axial flow fan in subway station project, reversible axial flow fan in airshaft tunnel are placed in the fan room in terminals of the station or along the tunnel for ventilation of stations and tunnel.

地铁工程车站可逆转高温轴流风机，区间风井隧道可逆转轴流风机，一般设于车站两端或区间通风机房内，用于车站、区间隧道通风。

Additionally, axodendritic syn apses betw een degenerated terminals and NTLIcontaining dendrites also exist in the spina l dorsal horn.

此外，脊髓后角内还存在变性终末与含NTLI树突形成的轴树突触。

This paper focuses on the performance improvement, it develops the controller of three axises and adjusts the control parameters in frequency-domain.

本论文针对转台的品质整定，基于频域法设计与实现了转台三轴的控制器，在频率域内整定了转台的动静态品质，并对整定过程中的问题和现象作了详细的分析和研究，提出了转台品质整定的关键点和注意点。

Numerical simulation of the steady cavitating turbulent flow in the whole flow passage of a Kaplan turbine has been carried out by using a full cavitation model and a mixture two-phase flow model.

采用一种完整空化模型和一种混合流体两相流模型，对轴流式水轮机全流道内的定常空化湍流流动进行了数值模拟。

In edge sizing, outer chamfers of the drawn cup with and without pre-holes as well as inner chamfers of the hole flange are analyzed.

在整缘方面，可分为杯状引伸件外圆角之整缘与凸缘轴内圆角整缘。

Screws; nut; washers; shells pad; pull burst, then the maximum burst; Self-Drilling; GB screw; tight set, machine-processed rice; axis with circlips, open file ring; pull the nail; Hexagon wrench; standard parts ; fasteners; order non-standard items; imports screw; high strength bolts; live bolt section; switch box screws; Electric screw; Electronics screws

螺丝；螺母；垫片；弹垫；拉爆，顶爆；自钻；国标丝杆；紧定，机米；轴用卡簧，开口档圈；拉钉；内六角扳手；标准件；紧固件；订做非标准件；进口螺丝；高强度螺栓；活节螺栓；开关盒螺丝；电器螺丝；电子螺丝

Circlips for shaft/hole; open grip rings; steel wire circlips; round wire snap rings; spring washers with internal teeth, external teeth, curve, wave; external tap round nuts, external tongue round nuts with long tap, external tongue round nuts with long tap and wing, etc; motorcycle accessories, auto transmission shaft rings, non-standard fasteners.

我公司按国际生产孔用挡圈，轴用弹性挡圈，开口夹紧挡圈，钢丝挡圈，DIN471 DIN472 DIN6799，特大挡圈200-800，厚度不限。各种内齿，外齿垫圈。鞍形，波形，推型弹性垫圈，各种规格型号的弹簧垫圈，不锈钢弹簧垫圈。以及单耳，双耳外舌园螺母等，摩托车配件，各种汽车传动轴卡簧及非标准件

The kiln body is divided into two sections of electrical furnace body and dynamic rotation with the kiln body constructed of clayed circular hearth uniformly inserted with 9 silicon carbon rods along the circular axis( one group made up of 3 rods and Y connection for every 3 groups).

窑体部分又分为电炉炉体和动力转动两部分，炉体部分采用粘土质圆形炉膛，沿圆轴向均匀插9根硅碳棒（每三根串联成一组，三组按& Y &接线）高铝质的陶瓷炉管又置于硅碳棒内周，通电后硅碳棒产生高温，加热炉管。

Methods Cut the scar along it's length with operation knife to form a scar-skin which thickness is of about 0.8~1.2mm,then cut off the scar tissues under the scar-skin,replant the scar-skin in the same place,enswathed the wound with proper pressure.

沿瘢痕纵轴在瘢痕内切口，手术刀锐性剥离，形成0.8～1.2mm厚的瘢痕皮，切除瘢痕皮下的瘢痕组织，将瘢痕皮原位回植，适当加压包扎。5～10天拆线，应用肤康霜或硅酮霜3～6个月。

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面，更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值，分为几个相等的区间作为横轴，并将各区间内所测定值依所出现的次数累积而成的面积，用柱子排起来的图形，也叫做柱状图。