内流的

In some extent, increasing the area of fuel nozzle will be improve the combustion efficiency of DR; 3, the angle between dual air-inlets have complex influence with the combustion of DR.

研究结果表明：(1)补燃室头部距离的增加能增强补燃室头部回流以及提高燃料在补燃室后段分布的均匀性，但也减少了燃料与空气在补燃室后段进行掺混和燃烧的长度：(2)在一定范围内，增加一次燃气喷嘴面积能提高冲压发动机燃料的燃烧效率：(3)进气道夹角对冲压发动机中燃料的燃烧影响复杂，对于采用对称结构喷嘴的冲压发动机，当进气道夹角等于180°时，燃料与空气的掺混效果最好；而对于一次燃气喷嘴采用不同偏心结构的冲压发动机，补燃室内流场与燃料燃烧效率随进气道夹角变化的规律基本相似。

A detailed analysis of the main circuit introduction, control method and working principle of the direct-drive wind energy conversion system are given to introduce the two important parts a of this paper: First part is the control method of the multiple boost convertor, the important instantaneous current control method of this paper is given through the analysis of the main circuit structure, control method and working principle. Then a steady-state analysis for low-frequency, a high-frequency component analysis, and a closed-loop tracking performance analysis for dynamic response are provided to analyze the method proposed; And the second part is the control method of invertor.

在系统变流器整体结构分析的基础上，引出本文重点研究的两个变流环节的控制：第一部分是系统升压斩波器的控制，通过分析相关主电路结构、原理，建立了数学模型，引出本文重点研究的瞬时值控制策略的概念和具体实现，并对升压斩波器的瞬时值控制策略进行了详细的高频、低频模型分析和稳态、动态性能分析；第二部分是系统并网逆变器的控制，通过对逆变器主电路的数学建模和控制要求分析，研究了并网逆变器的瞬时值控制策略，包括电感电流控制内环和直流电压控制外环的具体设计和实现方法。

Curvilinear calcification suggests an aneurysm but is a less specific finding because it can also occur in craniopharyngiomas and sphenoidal masses. The intense enhancement of the residual lumen is relatively specific, but differentiation from other masses may be difficult on CT scans depending on the timing and degree of vascular enhancement. The MR imaging features are usually diagnostic, although they can be very subtle [2]. Significant signal heterogeneity is seen with T1 hyperintense signal due to subacute thrombus or flow related enhancement. Areas of T2 hypointensity can be seen due to intracellular deoxy or methemoglobin, calcification, or flow void.

线样钙化提示动脉瘤，但不是一个非常特异的征像，因为这也可以见于颅咽管瘤和蝶骨肿瘤，管腔样明显强化更特异些，但是在CT上与其他肿瘤鉴别可能是困难的，因为这取决与增强的时间与血管强化的程度，MR的特征性表现是更具有诊断意义的，即使有时候可能表现的非常细微，在T1上可以看到明显的不同信号成分，这是由于亚急性的血栓或流动相关增强效应，T2序列上可以看到低信号区域，这是由于细胞内脱氧或高铁血红蛋白，钙化，或流空效应。

The evolution process under the control of the multigeodynamic force system (including the boundary forces of Eurasia-Pacific-Indian three massive plates around Nansha block, effects of the deep mantle, relative soft layer-sliding planes within Nansha lithosphere block and the earth's rotational inertial force) can be briefly divided four stages: the late Cretaceous to the early Eocene stage of uprilfing-erosion and shear-extension caused by the oceanwards-eastwards withdrew of Pacific subduction zone and the delamination of proto-subducted slab after the stage of pre-Cretaceous pre-rifting active continentoceanic plate margin. In this stage, the Nansha transcrustal layering-block started to move southeastwards on the Nansha transcrustal layer-sliding plane, meanwhile, the Andu-Bisheng and Liyue-Banyue basement layering-block slid on their upper-crust layer-sliding planes, and Xibu accretion zone was formed. Successively, it entered the stage of the mid-Eocene to early Oligocene, when NW-SE sea-floor spreading occurred in the southwest subbasin owing to the slip-line field initiated by the collision between the Indian and Eurasian plates, Zengmu foreland-basin started to develop in the same time. And in the stage of late Oligocene to early Miocene, near NS simple-shear extension and sea-floor spreading in the central subbasin of eastern South China Sea resulted from the south-southeastwards drawing-force of the mantle-flow. The crustal layering-blocks and the Miri accretion zone formed also in this stage.

南沙岩石圈新生代微板块及板内层块构造的动力演化过程，在多元动力等因素(如块体之外的欧-太-印三大板块运动边界力和地幔深部活动因素、块体内部软弱层滑面以及地球自转变化)控制下，大致经历了4个阶段的演化：从前晚白垩世的裂前活动陆-洋板块边缘阶段因太平洋俯冲带向东跃迁、原向NNW俯冲消亡的板片的拆沉、幔隆而进入晚白垩世-早始新世的隆升剥蚀、剪切伸展演化阶段，南沙超壳层块顺超壳层滑面祥东南运移、安渡-毕生与礼乐-半月基底层块沿上壳层滑面拆离，西布增生带形成；继而先后在中始新世-早渐新世期间受印-欧板块碰撞滑线场、地球自转加速影响出现西南海盆NW-SE向海底扩张和曾母前陆盆地的发育，和晚渐新世-早中新世期间南—东南向地幔流牵引造成的中央次海盆近NS向单剪伸展与海底扩张、壳体层块向南差异滑移、米里增生带形成；中中新世以来，印度-澳洲板块快速向北俯冲，构成今日南海格局。

According to the request of adopting advanced technology, the main designing has such contents as below:⑴ Designing the two-fluid nozzle that is based on the theory of air-atomize spraying.⑵ Designing and choosing the type of the axial fan that is used to supply assisted airflow to waft droplets that comes from nozzle.⑶ Designing the swaying outfit that can rotate the spray assembly at a speed and inside a angle in order to satisfy the spray request of different crops, different planting states and improve the uniformity of distribution, the deposition of droplet. Here, we select TYV type reduction gear motor to adjust the swaying speed and use course switch to adjust the swaying angle.⑷ Designing the lift outfit that can adjust the height of the spray assembly to satisfy the request of the crops of different tallness, different spraying range. Here, we select cylinder as the main component that can be used as kickstand and controlled easily.⑸ Designing the switch of the power supply that is put out of the greenhouse in order to prevent worker from poisoning. After the mist sprayer being made, the experiment is made to test the function of the greenhouse mist sprayer fully.

根据采用先进施药技术的要求，本研究的设计内容主要有：⑴采用气液两相流喷雾技术，基于气力雾化原理，设计双流体喷头；⑵采用辅助气流输送雾滴，气流源为风机，对风机进行设计、选型；⑶为满足不同作物、不同栽培情况及提高雾滴分布均匀性、沉积性的施药要求，设计能带动喷射部件在一定角度内、以一定转速的旋转摇摆机构，本研究选用调速电机调节其摇摆速度，并利用反向行程开关调节其摇摆角度；⑷为满足不同高度作物、不同射程的施药要求，设计能调节喷射部件高度的升降机构，这里选用气缸为主要构件，既可以起到整机支架的作用，又可方便进行升降、固定控制；⑸设计行程开关的控制电路以及整机的控制系统。

Pollution discharge pump, adopting special big channel impeller structure, greatly increases feculency discharging ability, and effectively make solid particle with diameter being 50% of pump outlet diameter; the type 4 can be fitted with various protective devices according to customer's requests, including stator winding temperature-rise protection, bearing temperature rise protection, oil container leakage protection, etc to enhance the exploitation reliability; adopting inner flowing recycling system to use medium cooling electric machine section to make usage more safe.

排污泵采用了独特的大通道叶轮结构，大大提高了污物通过能力，能有效的通过直径为泵口径约50％的固体颗粒；本泵型4可根据用户的要求安装各种保护装置，包括：定子绕组温升保护、轴承温升保护、油室漏油保护等以提高电泵的使用安全性；可采用内自流循环系统，利用介质冷却电机部分，使用更加安全，同时，还可以利用此结构将电泵以干式固定形式安装；采用最新材料精制而成的机械密封，其使用寿命可达8000小时以上；可采用双导轨自动耦合安装装置，使机组的安装、维修方便、快捷；可根据用户的需要配备各种形式的排污泵专用控制柜以实现自动化管理。

Focusing on the PGE enrichment mechanism in the basic-ultrabasic intrusions in the Panxi rift, firstly, through the interpretation of TM photograph, data processing of regional geochemical exploration and geophysical prospecting results of gravity, magnetic force and seism, we analyzed the controlling effect of structure and magmatic movement on the PGE mineralization; Secondly, through the study of volcanic apparatus, petrography, measurement of comprehensive geochemical section, isotope tracing and dating of typical PGE-rich melanocratic rock series, we discussed the sources of the PGE-bearing mafic-ultramafic intrusions and basalts, their timing, evolvement sequences, the geochemical processes of magma crystallization and fractionation, and the relationship between magma evolution and structural development; Finally, through the analysis of PGE and chalcophile elements concentrations in the melanocratic rock series and the contrastive study with the Noril''sk magmatic Ni-Cu-PGE sulfide deposit, its related continental flood basalts and Siberia Traps, we discussed PGE mineralization characteristics and its enrichment mechanisms in the melanocratic rock series in the Panxi rift.

本项目首先围绕川西地区主要的PGE矿床及伴生矿的地质环境和有关的地质构造背景，通过TM卫片解译、区域化探和重、磁及地震物探资料分析，总体把握构造及岩浆活动对PGE成矿的控制作用；然后通过对典型富PGE暗色岩套的火山机构地质构造、岩石岩相学、地球化学、同位素定年和示踪等方面的工作，分析本区基性－超基性含矿岩体与喷出岩之间的成岩物质来源、侵入时代及演化序列，研究该区同一岩浆房分异结晶的地球化学过程及其随构造发展的耦合关系；最后通过对暗色岩套PGE地球化学剖面分析以及与俄罗斯诺里尔斯克陆内裂谷溢流型玄武岩中PGE矿化的岩石－构造环境对比研究，探讨该区暗色岩套中的矿化特点和富集部位及其PGE富集机制。

Other conclusion include: the trip of transient protection must be locked when the power circuit breaker of transimission line operated,because the trip is incorrect at this time;the features of transient current and its energy is different between the fault and thunder over- voltage in transimission line,and them can be identified;the ratio of high frequency component of current in serise capaciters compensation line , SVC and HVDC system is far little than fault transient current, so all of them do not affect the working of trasient current protection.

研究了在串联补偿电容的输电线路上发生故障时，串联补偿电容的MOV非线性保护电路对暂态保护的影响。串补电容MOV保护电路的非线性电流高频分量含量很小。静止补偿器、高压直流输电系统换流器的非线性特性产生的谐波分量含量极少。仿真计算表明，在与暂态保护判据中高频分量对应的频率范围内，其电流对应的功率谱估计值大大低于线路故障时故障电流的功率谱估计值，因此它们都不会对暂态电流保护的正常工作产生影响。

D models are the most widely spread in the world of turbo-machinery for its simplicity, but they are indeed purely empirical correlations which not only fail to provide detailed information inside one or more components, but also require significant effort to recreate themselves if engine operating conditions or component representations change; quasi 3-D models have been the workhorses for compressor and turbine design for many years, and the primary benefit of using quasi 3-D system models is to facilitate the design and detail analysis of a particular component across the range of possible boundary conditions; Full 3-D models are gradually replacing quasi 3-D ones by virtue of requiring no exit flow angle model and loss model and being capable of predicting secondary flow in cascade.

零维模型由于使用时简单易行，因此在涡轮发动机的仿真中得到广泛应用，但零维模型作为纯粹的经验关系式无法反映部件内部的流动细节，并且一旦部件有少许改动则新特性的建立耗费巨大；准三维模型由于能够详细地提供部件内部的流动情况，方便设计而成为涡轮和压气机设计的主要工具；全三维数学模型正逐步取代准三维模型在涡轮设计中的主导作用，同后者相比前者能够预测叶轮机械内的二次流动，在粘性流计算时不需要气流角和损失的经验公式，因此拥有巨大的发展前景。

Then the priest dipped from the flowing waters of the Kedron a flagon of water, and, lifting it on high, while the trumpets were sounding, he ascended the broad steps of the temple, keeping time with the music with slow and measured tread, chanting meanwhile,"Our feet shall stand within thy gates, O Jerusalem."

那时祭司从汲沦溪的流水中，取了水来。当号筒吹响时，他高举水瓶，踏著音乐的节奏，缓缓地步上圣殿的台阶；且行且歌︰&耶路撒冷啊，我们的脚站在你的门内。&

She gently rebuff ed him, but agreed that they could be friends

她婉言拒绝了，但同意作为朋友相处。

If in the penal farm, you were sure to be criticized.

要是在劳改农场，你等着挨绳子吧！