内流

Following ISM superfusion, an agonal inward current was produced at a holding potential of -70 m in all H and DH neurons tested in oltage-clamp mode.

在电位箝模式中所有神经元在域电位－70m时可见电流内流现象。

Following ISM superfusion, an agonal inward current was produced at a holding potential of -70 mV in all VH and DH neurons tested in voltage-clamp mode.

在电位箝模式中所有神经元在域电位－70mv时可见电流内流现象。

A pressure correction equation is established by use of the finite volume method on nonorthogonal collocated grids, and its algebraic form is also given. The equation is applied to simulation of the flow field in an equilateral cavity and an inclined cavity with a tilt angle of 45°.

利用有限体积法建立了非正交同位网格系统中的压力校正方程，详细给出了压力校正方程的离散形式，并对正方腔及倾斜角为45°的斜方腔内流场进行了数值模拟计算。

Heat intolerance with hypohidrosis or anhidrosis has been recently reported in children undergoing epilepsy treatment with TPM.

可以增加γ-氨基丁酸激活GABAA受体的频率，加强氯离子内流，增强抑制性中枢神经递质的作用[4，5]；3。

Based on engineering design method and combined with numerical simulation,an axial symmetry supersonic inlet with boundary layer bleed was designed.

应用工程设计方法，结合数值模拟，设计了一种带有边界层吸除型式的超声速轴对称进气道，对进气道内流场进行了数值模拟研究，并且进行了风洞实验。

This part of Ca〓 was mobilized and disappeared in capacitation process.

精子获能过程中外源Ca〓内流，结合于质膜内侧和顶体外膜外侧。

FLUENT is one of business software that used to simulate the compressible fluid.

通过CFD软件FLUENT分别利用可压缩流体的三维湍流模型和无粘流动模型对改进前后喷油嘴内流场进行了数值模拟。

A method to simulate the fluid flow and temperature distribution in slab continuous casting mold has been introduced in this paper.

连铸过程是一个同时包含凝固、传热、流体流动等复杂现象的综合过程，对结晶器内流场和温度场的计算机仿真研究一直是比较活跃的研究领域。

The secondary mass flux, Z, cavity convergence/divergent angle, and injection angle have different effect on internal performance of DTN.

二次流量、落压比、凹腔扩张角和收敛角、引射角度都对推力矢量状态下的DTN内流性能有着不同的影响。

In order to achieve a tradeoff between vectoring and unvectoring state, the proposed parameters of DTN are: Z=3~4, secondary injection flux is about 3%, cavity divergence angle is about 10°, cavity convergence angle is 20°~30°, injection angle of secondary is about 30° by counterflow injection.

为了实现DTN在推力矢量和非推力矢量下都有较好的内流综合性能，所建议的设计参数为：落压比为3~4，引射量为3%，凹腔扩张角为10°左右，收敛角在20°~30°，引射角度为30°逆流引射角(β=30°)。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。