内流

The basal pacemaking activity of SAN cells was highly dependent on the calcium influx. Elevation of 〓 concentration (4mmol/L) in the perfusate partially antagonized the inhibitory effects of Dip on APA,〓, VDD and RPF.

窦房结细胞的起搏活动在很大程度上依赖于〓内流，提高灌流液中〓浓度（4mmol／L）可部分拮抗Dip对APA、〓、VDD和RPF的抑制作用，使其降低这些参数的作用减弱。

The numerical simulation of the motor cold flow field and the mixing process of various kinds of gases are performed by PISO algorithm.

采用PISO算法模拟了冷流状态下发动机的内流场和各种气体组分的相互掺混过程。

To solve the practical problem where the temperature field distribution is low at the lower part of furnace chamber and high at the upper part and the temperature difference is untolerable , which is reflected by the thermocouples at site, the authors take the methods of multipoint test and computer hologram simulation to research into the fields in the furnace chamber of the zinc fractionating tower at Shaoguan Smelter CNNC.

针对锌精馏炉炉膛各检测点反映出的其上部温度偏高，下部温度偏低，上下温度偏差过大的实际问题，采用现场多点温度测试，结合炉膛内流场、浓度场、释热场和温度场数值仿真的方法对韶关冶炼厂二精馏系统进行研究；利用仿真结果中的流场扣浓度场数据，统计出实测中无法得到的各次空气和煤气在南1号至南4号各喷口的流量。

A water model for simulation of 1050 mm mold is established to investigate the effects of SEN structure, casting speed, immersion depth and other parameters on the fluctuation of the liquid level in the mold, the impact depth of the steel stream and entrapping of the flux, and compare the influence of different structure parameters and operating parameters on the flowing field in the mold in order to find out the best suitable compromise between the structure parameters and the operating parameters and then...

针对 10 5 0mm× 15 0mm断面的结晶器，建立了水模型，研究浸入式水口结构、拉速、浸入深度等工艺操作参数对结晶器液面波动、流股冲击深度及结晶器钢液面保护渣卷入情况的影响，比较不同水口结构参数及操做参数对结晶器内流场的影响，从而找出结构参数与工艺参数间配合最佳的工况，为水口设计提供理论依据，并经优化的水口在实际中应用，使安钢第二炼钢厂的板坯退废率由 1.5 0 %降为0 。6 %。

The thesis tells the suitable fluid field and velocity field as result of suitable position and quantity for argon blowing. And the ladle furnace turns into a better reactor of uniformity of the composition, floatation and removal of inclusions.

通过研究得出了钢包内流场以及速度场的分布，通过调整底部透气砖位置和气体流量，达到了最佳的流场状况，使其成为了一个能为钢液均匀、夹杂物上浮和去除提供最大可能的反应器。

Regarding to model 1, firstly analyzes and studies principle as well as formation of detonation wave, the internal flow field structure of the detonation chamber. Then study the flow field structure near the outdoor of the detonation chamber, backflow process of the dilatation wave after detonation wave reach the outdoor and the change of thrust wall pressure and so on.

对于模型1，首先分析研究爆震波在爆震室内形成传播机理和爆震室的内流场结构，然后研究爆震波传出爆震管以后爆震管出口处的流场结构，膨胀波的回传过程以及推力壁压力随时间的变化等。

Taking velocity moment as controlled variable, the formulas were deduced to calculate quasi-3D inverse problem for uniform stream model of guide pulley. According to the theory of two relative flow surfaces and the force analysis of air bubble, the formulas were deduced to calculate quasi-3D direct problem while gas and liquid running in the guide pulley of multiphase pump, and a method was provided to carry on quasi-3D numerical calculation of inner flow filed.

以速度矩作为控制参数，推导出多相泵导轮中均匀流模型的准三维反问题计算公式；基于两类相对流面理论及气泡的受力分析，推导出气、液两相在多相泵导轮中运动的准三维正问题的计算公式，提出一种对多相泵导轮内流场进行准三维数值计算的方法。

Peng Shan, Non-install Integral Performance Simulation of a Cycle Variable Supersonic Through Flow Fan Propulsion System, Journal of Gas Turbine Experiment and Research, Vol.

单鹏，超音通流风扇变循环推进系统内流特性模拟，燃气涡轮试验与研究，12卷1期， 1999年。

Numerical simulation was conducted to investigate the flow field of internal cooling passages with both rib-roughened walls and film hole suctions and discharge coefficients of film holes,with rib angles 45°,60°,90°,120°respectively.

利用有限体积法对三维不可压缩的N-S方程进行离散，对同时带肋和气膜孔出流的内流冷却通道在45°，60°，90°，120°肋的结构下进行了数值模拟。

Constructing model apparatus system of bell-like suction box, the outlet section velocity distribution was measured by probe under various suction open heights.

以流道出口速度均匀度、速度加权平均角、水力损失大小为评价目标函数，研究了钟形进水流道不同喇叭口悬空高度的内流场特征和水力损失特性，提出了喇叭口悬空高度的合理取值范围。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。