内开锁

Lid done with stainless steel plate floor, built-silicate insulation, Furnace Door size 350 mm wide, 580 mm high, the overall lateral wall elevate electric holding furnace door, Furnace Door closure of the Furnace Door as a whole round , Furnace Door sealing performance enhancements, dial made of stainless steel by 1600 m / m turntable, used to load the workpiece, the entire wheel of the plane is not division, the operator can be stacked workpiece, as dial-rotation every 40 minutes a week , when the operator can not see dial in almost rotation, and Furnace Door open the larger operators can be arbitrary and out of the workpiece, and without time limits can dial in 20-60 minutes a week to arbitrary rotation speed, regardless of Furnace Door hoist, from the start of work on the dial continuous rotation, and there was no need for chain hoist Furnace Door, the need to stop rotating, just press the control cabinet, stop button, the gate Furnace Door, operators to seize its own, activated installed in the furnace door open and close button.

炉盖采用不锈钢板做底板，内置硅酸铝保温，炉门尺寸宽350mm，高580mm，侧墙体中整体向上提升式电动保温炉门，炉门关闭时整个炉门为一个圆形整体，炉门密封性能增强，转盘采用不绣钢制成1600m/m转盘，用以承载工件之用，整个转盘为平面不分工位，操作人员可以任意堆放工件，由于转盘每40分钟旋传一周，工作时操作人员几乎看不到转盘在转动，加上炉门开的较大，操作人员可以任意进出工件，而不受时间限转盘可以在20--60分钟旋转一周的时间任意调速，不论炉门启闭、转盘从启动工作就不间断的旋转，没有任何必要与炉门启闭进行联锁，需要停止旋转时，只需按下控制电柜上的停止按钮即可，炉门的启闭，由操作人员自行掌握，按动安装在炉门边的启闭钮即可。

METHODS: The 15 hybrid dogs were randomly divided into 2 groups. In the experimental group (n=9), a hole was drilled at the slope beneath the tibial plateau to reach the medullary cavity. The cavity was enlarged by an appropriate drill to confirm the size of the cavity. The absorbable polyamide intramedullary rods were inserted from the hole in tibial superior extremity, and the fracture was anatomically reduced with the rod passing through the fracture. Two locking nails, which were cylinder polyamide rods, were respectively located 2 cm from the cutting site, in the distal and proximal ends. Auxiliary plaster external fixation was performed for 4 weeks. In the control group (n=6), quincunx intramedullary nails of the same diameter with 4 pre-drilled holes were accordingly inserted into the cutting segment, and 2 screws were locked in the distal and proximal ends, respectively.

15只杂种犬随机分为2组，实验组(n=9)：在距离胫骨平台下斜坡处钻孔入髓腔，用合适钻头扩大髓腔，确认髓腔大小，从胫骨上端开孔插入聚酰胺钉，解剖复位骨折端并使该钉通过骨折处，在距离截骨处2 cm处的远近端分别锁上2枚锁钉，锁钉为圆柱形聚酰胺棒，辅助石膏外固定4周；对照组(n=6)：同样插入相应直径的、已预钻4孔的梅花形髓内钉截段，在骨折端的近端及远端分别锁2枚螺钉，辅助石膏外固定4周。

1 The lowest, 10 the highestI mean let's not joke around!! An iverson shoes with great ankle support( think about the answer 5 and answer 6)?? come on give me a break!! well no doubt! ANSWER 10 must be one of the best ankle supporting shoe on the market right now!! First of all let's talk about how this shoe protects the ankle for a baller like you and me. The TPU plate which locates at back of yout ankle creats a secure fit that locks in your ankle so your foot will not move around like a pair of Chuck Tayler and with the additional inner bootie, its like heaven when you walk around with it !! YET the adjustable Pump system gives the shoes a big bonus by having air surrounding you foot ( air bolloon??) so your ankle will unlikely to rollover!!

我必须很认真的告诉您，您能想像艾佛森的个人鞋款有完美的踝部支撑吗(想一想 answer 5 and answer 6)，别开玩笑了吧，但是无庸置疑的，ANSWER 10 绝对是目前市面上拥有最好的踝部支撑的鞋款之一，先让我们讨论一下这双鞋是怎样保护一个像您跟我一样篮球员的脚踝的，坐落在脚踝正后方的 TPU plate 让您感觉您的脚踝就好像是被安全的锁住了一样，让您的脚踝不会在鞋内摇来摇去的(某 converse 鞋款)，还有，无缝线的内衬让您穿上它走来走去之后，就感觉好像是先开了套房再在水床上天堂一样，还有可调整式的 Pump system 给予了这双鞋大大的加分因为当您穿著它走来走去时您一定可以感受到 air 紧紧的包住了您的脚踝，这样一来您的脚踝就更不会轻易的翻船了。

In accordance with "anti-theft security door general technical conditions" provides a qualified anti-theft door within 15 minutes, using chisels, screwdrivers, crowbars and other common hand tools and portable electric tools such as hand drills can not be forced open, or opening a door from a 615 mm2 of the openings, or in lock-point 150-square-millimeter semi-circular opening within a 38 square millimeter openings.

按照《防盗安全门通用技术条件》规定，合格的防盗门在15分钟内利用凿子、螺丝刀、撬棍等普通手工具和手电钻等便携式电动工具无法撬开或在门扇上开起一个615平方毫米的开口，或在锁定点150平方毫米的半圆内打开一个38平方毫米的开口。

When the key inserted within CORE , Billiard and the turning key match ,As long as we turn the key, Therefore, the position reached unlock.

当钥匙插入锁芯内时，下弹子与转弯的钥匙相吻合，转动钥匙，达到开锁的位置。

The outer key can retract the latch bolt when the inner lock mechanism is in the locked state, but cannot change the inner lock mechanism to the unlocked state or enable the outer handle, thereby ensuring positive control over the locked state of the outer handle from the inner side.

外钥匙(60)在内锁机构处于锁住状态时能缩回弹键栓，但是，不能将内锁机构变成开锁状态或允许外拉手(36)操作，从而可保证从内侧对外拉手(36)的绝对控制。

The outer handle can only retract the latch bolt when both the inner and outer lock mechanisms are in the unlocked state.

外拉手(36)只有当内、外锁机构都处于开锁状态时才能缩回弹键栓。

The bung uses the stainless steel plate to make the ledger wall, the built-in aluminum silicate heat preservation, the fire door size extends 350mm, high 580mm, in spandrel wall body whole upward promotion type electrically operated heat preservation fire door, when fire doorclosure the entire fire door is a circular whole, the fire door sealing property strengthens, the turntable uses the stainless steel to make the 1600m/m turntable, with take load bearing work piece, the entire turntable does not divide the location as the plane, the operators may pile up the workpiecewillfully, because turntable every 40 minutes turn on lathe biography one week, when work the operators did not look nearly the turntable in the rotation, the fire door starts in addition in a big way, the operators may pass in and out the work piece willfully, but is not limited the time the turntableto be possible in 20-60The minute revolves one week-long time to modulate velocity willfully, no matter the fire door opens shuts, the turntable from the start work on uninterrupted revolving, not any necessity and the fire door open shut carry on the interconnection, needs to stop when revolves, onlyneed press down on the control electricity tank's pause button then, the fire door opens shuts, grasps voluntarily by the operators, presses installs nearby the fire door opens shuts button then. Transfers the bottom type resistance furnace's temperature control part to use the microcomputer automatic

炉盖采用不锈钢板做底板，内置硅酸铝保温，炉门尺寸宽350mm，高580mm，侧墙体中整体向上提升式电动保温炉门，炉门关闭时整个炉门为一个圆形整体，炉门密封性能增强，转盘采用不绣钢制成1600m/m转盘，用以承载工件之用，整个转盘为平面不分工位，操作人员可以任意堆放工件，由于转盘每40分钟旋传一周，工作时操作人员几乎看不到转盘在转动，加上炉门开的较大，操作人员可以任意进出工件，而不受时间限转盘可以在20—60分钟旋转一周的时间任意调速，不论炉门启闭、转盘从启动工作就不间断的旋转，没有任何必要与炉门启闭进行联锁，需要停止旋转时，只需按下控制电柜上的停止按钮即可，炉门的启闭，由操作人员自行掌握，按动安装在炉门边的启闭钮即可。

The bung uses the stainless steel plate to make the ledger wall, the built-in aluminum silicate heat preservation, the fire door size extends 350mm, high 580mm, in spandrel wall body whole upward promotion type electrically operated heat preservation fire door, when fire door closure the entire fire door is a circular whole, the fire door sealing property strengthens, the turntable uses the stainless steel to make the 1600m/m turntable, with take load bearing work piece, the entire turntable does not divide the location as the plane, the operators may pile up the work piece willfully, because turntable every 40 minutes turn on lathe biography one week, when work the operators did not look nearly the turntable in the rotation, the fire door starts in addition in a big way, the operators may pass in and out the work piece willfully, but is not limited the time the turntable to be possible in 20-60The minute revolves one week-long time to modulate velocity willfully, no matter the fire door opens shuts, the turntable from the start work on uninterrupted revolving, not any necessity and the fire door open shut carry on the interconnection, needs to stop when revolves, only need press down on the control electricity cabinet's pause button then, the fire door opens shuts, grasps voluntarily by the operators, presses installs nearby the fire door opens shuts Niu then.

炉盖采用不锈钢板做底板，内置硅酸铝保温，炉门尺寸宽350mm，高580mm，侧墙体中整体向上提升式电动保温炉门，炉门关闭时整个炉门为一个圆形整体，炉门密封性能增强，转盘采用不绣钢制成1600m/m转盘，用以承载工件之用，整个转盘为平面不分工位，操作人员可以任意堆放工件，由于转盘每40分钟旋传一周，工作时操作人员几乎看不到转盘在转动，加上炉门开的较大，操作人员可以任意进出工件，而不受时间限转盘可以在20—60分钟旋转一周的时间任意调速，不论炉门启闭、转盘从启动工作就不间断的旋转，没有任何必要与炉门启闭进行联锁，需要停止旋转时，只需按下控制电柜上的停止按钮即可，炉门的启闭，由操作人员自行掌握，按动安装在炉门边的启闭钮即可。

The bung uses the stainless steel plate to make the ledger wall,the built-in aluminum silicate heat preservation, the fire door size extends 350mm, high 580mm, in spandrel wall body whole upward promotion type electrically operated heat preservation fire door, when fire door closure the entire fire door is a circular whole, the fire door sealing property strengthens,the turntable uses the stainless steel to make the 1600m/m turntable, with take load bearing work piece, the entire turntable does not divide the location as the plane, the operators may pile up the work piece willfully, because turntable every 40 minutes turn on lathe biography one week, when work theoperators did not look nearly the turntable in the rotation, the fire door starts in addition in a big way, the operators may pass in and out the work piece willfully, but is not limited the time the turntable to be possible in 20-60The minute revolves one week-long time to modulate velocity willfully,no matter the fire door opens shuts, the turntable from the start work on uninterrupted revolving, not any necessity and the fire door open shut carry on the interconnection, needs to stop when revolves, only need press down on the control electricity cabinet's pause button then, the fire door opens shuts,grasps voluntarily by the operators, presses installs nearby the fire door opens shuts Niu then.

炉盖采用不锈钢板做底板，内置硅酸铝保温，炉门尺寸宽350mm，高580mm，侧墙体中整体向上提升式电动保温炉门，炉门关闭时整个炉门为一个圆形整体，炉门密封性能增强，转盘采用不绣钢制成1600m/m转盘，用以承载工件之用，整个转盘为平面不分工位，操作人员可以任意堆放工件，由于转盘每40分钟旋传一周，工作时操作人员几乎看不到转盘在转动，加上炉门开的较大，操作人员可以任意进出工件，而不受时间限转盘可以在20—60分钟旋转一周的时间任意调速，不论炉门启闭、转盘从启动工作就不间断的旋转，没有任何必要与炉门启闭进行联锁，需要停止旋转时，只需按下控制电柜上的停止按钮即可，炉门的启闭，由操作人员自行掌握，按动安装在炉门边的启闭钮即可。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。