内圆角

In order to distinguish the different faces of link plates on line, an approach to automatic brand recognition of link plate was developed in this paper, which is applicable for various kinds of brand images.

引言链条链板是采用冲裁的方法加工的，链板正、反表面周边及内孔存在一定的差异，如存在圆角区、光亮区和断裂区，这种加工上形成的差异对装配后链条的质量有很大的影响 [1，2 ]。

The faces of turbine blade s body is complex,in the general CAD platform,fitting spline of intrados and convex based on points of data,creating fillet of leading edge and trailing edge,and achieving the body of turbine blade at last are all complicated processes.

汽轮机叶片叶身型面比较复杂，在通用CAD系统中，根据数据点拟合出内、背弧样条曲线，修进出汽边圆角，最后根据每个截面形状得到叶身实体，都是比较复杂的过程。

And on the basis of analyzing the geometry characteristics of the side rail, the corners whose radius deteriorates the formability are modified.

重点对高强度钢纵梁内板的成形性进行了分析，并且在详细分析零件几何特点的基础上，对此模型的圆角半径进行了修改，修改后零件的成形性得到了显著提高。

A technique which can control the iteration step length of the single step full Newton Raphson method is presented to get the converged solution.

纺织物的弯曲刚度比其面内拉伸剪切刚度小得多，其下垂过程具有高度几何非线性，它能在经向和纬向同时屈曲，形成漂亮的圆角形状。

Experiments exposed that the inner flow of tooth space in the micro-channels was proved to be cycled flow after fully development. For the more, low velocity vortex cavities existed in the vertex angle and inner side of bend angle of straight angle micro-channel, while back flow only appeared in the internal side of bend angle of round angle micro-channel. It's easy to take place deposition in the low velocity vortex cavities, which is the main cause of blocking.

试验发现各类微通道齿间内流充分发展后是一种重复性流动，平角微通道顶角和转角内侧存在低速涡旋区，圆角微通道只在转角内侧出现回流，颗粒在低速涡旋区易发生沉积，是造成堵塞的主要原因。

Add a slight Inner Glow to the rectangle, using white at 5px in size to give a very slight bevelled edge effect.

再次为这个圆角矩形兄添加一个内发光，白色的5像素即可，这样会让边线产生一个很细小的倾斜效果。

The results indicate that the largest deformation appear on the middle region of the addendum, the position of largest stress appears at the dedendum region of loaded tooth. As the curvature radius of transition curve rising, both the largest deformation and the largest dedendum stress reduce.

结果表明，内齿圈的最大变形出现在齿顶的中间部位，而最大应力出现在受载齿的齿根部位；内齿圈的最大变形和齿根最大应力随着齿根过渡圆角半径的增大而减小。

8T ball mill has new constructure inner liner with transiting round corner and uncontinuous spiral which is built by alumina corundum-based heteromorphic brick and common ceramic tiles.

8吨球磨机应用氧化铝刚玉质异形砖与普通瓷质砖砌筑成具有过渡圆角及不连续螺旋的新结构内衬，在广东某大型企业的生产线上球磨陶瓷耐磨地砖釉料，并就釉料颗粒大小及粒度分布、电耗、介质磨耗等与1.5吨球磨机进行对比，进行了实验研究。

Based on the relations among the stress, final wall-thickness of thin-walled tube and the characteristics of tube material, original size, curling radius along with friction condition in a axially-compressed internal inversion process on right-angled fillet die, some analytical discriminants were established for judging if a double-layered tubular piece of aluminum alloy could be steadily formed from a certain-sized round tube via internal inversion process without interference and plastic instability of tube wall, and a method was put forward for determining the maximum and minimum usable curling radius or die fillet-radius for thin-walled tubes in the process.

基于薄壁管直角圆角模轴压内翻过程中各处应力及最终壁厚与管材特性、管坯尺寸、卷曲半径及摩擦条件之间的关系，推出了判别任一铝合金双层管件可否由特定尺寸圆管稳定内翻成形而不出现管壁干涉与塑性失稳问题的解析判别式，指出了确定薄壁管圆角模内翻卷曲半径或模具圆角半径极限值的方法。

In edge sizing, outer chamfers of the drawn cup with and without pre-holes as well as inner chamfers of the hole flange are analyzed.

在整缘方面，可分为杯状引伸件外圆角之整缘与凸缘轴内圆角整缘。

Plunder melds and run with this jewel!

掠夺melds和运行与此宝石！

My dream is to be a crazy growing tree and extend at the edge between the city and the forest.

此刻，也许正是在通往天国的路上，我体验着这白色的晕旋。