公式的

According to the main influencing factors, this thesis summarized the mathematic method based on the Larson-Miller formula of the service life analysis for the superheater and reheater; and intensity check method of the service life for the economizer, and the service life analysis process for waterwall.

根据其主要影响因素，本文分别总结出了过热器再热器寿命基于Larson-Miller公式的分析方法，省煤器寿命的强度校核分析方法，和水冷壁的寿命分析流程。

A theoretical model to describe the relationships between wear and electric resistance of thick film sensors is given.

得到的磨损量与厚膜电阻值之间的关系可由基于电阻率公式的理论模型加以描述。

On the basis of a review of their work in this area over the past fifty years the authors have analyzed the merits and demerits of empiric formulas presented by various scholars.

本文通过对近50年来在这一领域内工作的回顾，分析了不同学者所获得的经验公式的利弊。

Through calculating the stabilization reliability index of steel members under compressive axial loads based on Euler formula considering initial bend and initial deflection, it finds that reliability index of steel members considering initial disfigurement is smaller than the steel members regardless of initial disfigurement.

本文通过分析考虑初弯曲的基于欧拉公式的轴向受压钢构件的稳定可靠性指标和考虑

Through an engineering example, the formulae of excess pore water pressure was verified.

结合一具体工程事故的成功处理，验证了所建议超孔隙水压公式的可行性，同时提出了减少超孔隙水压的对策和方法。

Facts and formulae of the past have, in their eyes, only a symbolic and a transient value.

事实和公式的过去，在他们眼里，只有一个象徵性的和短暂的价值。

Comparison with experimental data reveals that the new hypothesis as well as the new formulae is reasonable and applicable.

同实验数据的对比证实了本文所提出的理论和公式的合理性。

It mainly deals with: 1 the adoption of PW-30 and PWC drag reduction materials through screening, which were found to be of better kinds with large percentage of drag reduction in low concentration and fine solubility; 2 fundamental data and basic formulae of drag reduction; 3 predictional method of drag reduction in internal flow e.

包括以下几个主要部分：筛选了减阻剂，所得到的PW-30及PWC具有在低浓度下高减阻百分数及速溶等性能，系两种优良的减阻剂。讨论了基础数据及消防减阻予报公式的整理和减阻予估方法。提出了系统匹配与优化减阻问题。

Through statistic analysis tools as re gress analysis and response surface method, an empirical formula of surface roug hness and cutting parameters is estab...

研究结果表明，高速铣削马氏体不锈钢时，每齿进给量、铣削深度和两者之间的交互作用是对表面粗糙度有显著影响的效应因素，所得经验公式的模型适合度检验结果较为理想。

As a result accurate computing results are verified through comparing with the test datum, while the formulae also indicates that shear span ratio is the major influence factor of horizontal projection length.

推导公式的计算结果和试验实测值取得了很好的吻合，误差小，离散程度低，同时还表明剪跨比是影响斜裂缝投影长度的主导因素。

She gently rebuff ed him, but agreed that they could be friends

她婉言拒绝了，但同意作为朋友相处。

If in the penal farm, you were sure to be criticized.

要是在劳改农场，你等着挨绳子吧！