公差制

Our process capability: Plates: FR4, High TG FR4, high CTI FR4, high frequency materials, halogen-free materials, aluminum and other low-rise Materials :2-20 layer of finished copper thickness :0.5-5 OZ finished thickness: 0.2 -6.0mm Minimum line width: 3mil Minimum line spacing: 3mil smallest shape tolerances:+/-0.1mm minimum finished diameter: 0.1mm maximum thickness aperture ratio: 12:1 wide minimum solder bridge: 4mil characters minimum line width: 5mil Minimum height of characters: 30mil Solder Mask Color: Green, black, blue, white, yellow, purple characters such as color: white, yellow, black and other surface processes: spray tin, lead-free HASL, Electroless gold plating Shuijin, OSP, chemical Shen tin, silver and other chemicals Shen Process: Goldfinger, blue gum, Blind-via/Buried-via, characteristic impedance control, rigid-flexible combination of reliability testing such as: Open / Short testing, impedance testing, solderability testing, thermal shock testing, metallographic analysis of micro-slice curvature Isoptera: 0.7% flame retardant Level: 94V-0

我们公司的制程能力：板材：FR4、高TG FR4、高CTI FR4、高频材料、无卤素材料、铝基材料等层数：2-20层成品铜厚：0.5-5 OZ成品板厚：0.2-6.0mm最小线宽：3mil最小线间距：3mil最小外形公差：+/-0.1mm最小成品孔径：0.1mm最大板厚孔径比：12：1最小阻焊桥宽：4mil最小字符线宽：5mil最小字符高度：30mil阻焊颜色：绿色、黑色、蓝色、白色、黄色、紫色等字符颜色：白色、黄色、黑色等表面工艺：喷锡，无铅喷锡、化学沉金、电镀水金、OSP、化学沉锡、化学沉银等其它工艺：金手指、蓝胶、盲埋孔、特性阻抗控制、刚柔结合等可靠性测试：开/短路测试、阻抗测试、可焊性测试、热冲击测试、金相微切片分析等翅曲度：≤0.7%阻燃等级：94V-0

Point out the reference system of fits and types of fitting, and marking tolerance on a detail drawing.

指出所采用的基准制和配合种类，并在零件图中标注公差尺寸。

Point out the reference system of fits and types of fitting, and markingtolerance on a detail drawing.

指出所采用的基准制和配合种类，并在零件图中标注公差尺寸。

Tolerance allocation is according to the precision variation requirement and product processing cost. The method used for sequential quadratic programming algorithm. In the optimum model, the objective is to minimize the summation of product processing cost and then to construct the tolerance stack-up constraint conditions and the self-tolerance boundary constraint conditions.

公差配置则是根据精度变异范围进一步分析其成本，透过使用序列二次规划最佳化方法，以最小制程成本为目标，建立主轴组装误差堆叠限制条件与个别公差限制条件作公差配置。

On the other hand, inch-dimensioned tapered roller bearings have plus tolerances; the nominal dimension represents the lower limit

另一方面，以英制尺寸为标准的圆锥滚子轴承有另外的公差标准；近似尺寸代表下限。

Finally, according to market conditions and market products this article paper analyzes the trends in the development of camera technology, and designs a color night vision camera.

最后根据市场情况和市面上产品的情况分析了摄像机技术的发展趋势，并设计了一款彩色夜视摄像机。

Only person height weeds and the fierce looks stone idles were there.

只有半人深的荒草和龇牙咧嘴的神像。