入孔

The machine is a dedicated Milling Machine, Its bed and the overall structure of a lathe, Cutting function of the milling, Principle of its total whole installation box cutter and the drive shaft extension units of a large Worktable movement, Enter the hole, With Finger-shaped cutter Milling to Processing the hole keyway.

本机床是一台专用的车铣床，其床身和总体结构为一台车床，切削功能为铣削，其总原理为将整个铣头和传动轴通过大拖板的运动，伸入孔内，用指状铣刀来铣削加工内孔键槽。

Planting bar used syringes from the bottom of the hole to put adequate amounts of external uniform adhesive filling injection hole, pay attention not to air hole inclose.

使用植筋注射器从孔底向外均匀地把适量胶粘剂填注孔内，注意不要将空气封入孔内。

There were the intrajugular processes of the petrosal and occipital bone in the JF.

岩骨和枕骨向JF内发出颈静脉内突(intrajugular press，IJP)并凸入孔内，10％JF中两侧的IJP相互融合形成骨桥。

Results Surgical instruments broken in the articular cavity took place in 8 cases, injury of the normal tissue including the cartilage, meniscus, and ligaments happened in 40 cases, nerve branch and vascular injured around the inlets in 11 cases, water seeping out in 13 cases, infection following the formation of hematoma in 5 cases, refracture of patella during operation in 1 case, myocardial infarction after operation in 1 case, totally, complications and accidents were seen in 79 cases (5.1％).

结果在施行关节镜检查或术中、术后发生各种并发症及意外者79例(5.1％)，其中发生关节内各种器械断裂8例，关节内正常组织损伤40例，关节镜入孔周围组织结构损伤11例，冲洗液外渗13例，关节血肿、感染5例，术中髌骨再骨折1例，术后突发心肌梗死1例。

In order to ascertain the causes and mechanisms of corrosion and abrasion failure,the demonstration analyses and experiments such as macro/microscopy and corrosion substance composition analyses were carried out on the broken section of the man-hole door of refeed valve and air-hood .

重点对返料阀入孔门盖及风帽吹气管断口的宏微观形貌、微区成分、腐蚀物组成等进行表征分析和试验，确定腐蚀磨损产生的原因及腐蚀机理；最后根据实际状况，提出相应的预防措施和建议。

Methods Supraorbital foramen, infraobital foramen and oval foramen radiofrequency thermocoagnlation were performed on 64 patients with trigeminal neuralgia.

分别采用眶上孔、眶下孔、侧入路卵圆孔或Hartel前入路卵圆孔穿刺法，射频温控热凝术治疗三叉神经痛64例。

The length of the tremie should be calculated in advance and the inner wall and the thread at the joint should be cleaned.

导管入孔前，应计算好长度，导管内及丝口应清理干净。

This paper presents the experiment research for unchamfered peg in hole assembly task based on the principle of ARCC, introduces the structure of the experiment system, the close loop stiffness of the ARCC system and the element setting of the decoupling force feedback matrix.

本文根据ARCC的工作原理，对机器人的无倒角插轴入孔装配作业进行了实验研究，介绍了实验系统的组成，ARCC系统闭环刚度和去耦力反馈矩阵的设置。

The types of film hole infiltration can be classified as single point source infiltration, single-line interference infiltration and multiple-line interference infiltration.

膜孔入渗为充分供水条件下的空间三维入渗，可分为三种类型：膜孔自由入渗、膜孔单向交汇入渗和膜孔多向交汇入渗。

One is the wire-wound spring into cylindrical shape or rolling circle equipment into ready-to-wear pressureof ship'spennant bookbiding shape metal ring, having been set before even having the mouth perforatig, metal ring by hand or machine mode into the holes in the even of a commentary.

一种是将金属丝绕卷成圆柱弹簧形状或用卷丝圈设备卷成可直接穿压的长条形状金属环，装订时先在被订连本册的订口上打孔，再将金属环用手工或机器方式穿入孔眼内订连成册。

In the negative and interrogative forms, of course, this is identical to the non-emphatic forms.

。但是，在否定句或疑问句里，这种带有"do"的方法表达的效果却没有什么强调的意思。

Go down on one's knees;kneel down

屈膝跪下。。。下跪祈祷