光条纹

The air wedge angle can be computed with application of the unitary linearity regress method in fitting the relation between the serial number of the CCD pixels and the serial number of the intensity maximum of interference fringes.

该方法利用待测试件受力产生的形变改变空气劈尖顶角，并用一元线性回归方法对CCD的像元序号与所接收到的干涉条纹光强极大值序号之间线性关系进行拟合，进而确定出空气劈尖顶角大小。

In the typical setup of Michelson interferometer, turning the tested object a small angle generates an air wedge between the object plane and the reference plane. The wedge produces equal thickness interference fringes.

采用典型的迈克尔逊干涉光路，将物体偏转一微小角度（等效为物面与参考面间形成空气楔）产生等厚干涉，可在物体的表面引入包含物体高度信息的载波干涉条纹。

In this system, the gratings are inscribed by the UV interference fringes of 248 nm derived from a rotatable biprism, where the phase mask is used as a beam splitter, and the biprism is rotated to change the intersection angle of two beams.

在该系统中，光纤光栅是由来自可旋转双棱镜所形成的波长为248 nm的紫外干涉条纹写入的，其中，相位掩模被用作1级衍射光的分束器，通过双棱镜的旋转可改变两写入光束的交叉角。

Light from a mercury arc lamp will produce fringes over a range of one or two centimeters.

汞灯泡发出的光产生一到二厘米范围以上的条纹。

Grating-mirror is designed, and it can be not only used as a grating but also a mirror. It reflects moiré fringe image formed by grating imaging back into autocollimator which will be acquired by CCD detector.

设计了光栅反射镜，使其同时起到光栅和反射镜的作用，将光栅叠加成像后得到的莫尔条纹图反射回自准直光管，并被CCD探测器接收。

For the laser coordinate measuring machine, the single CCD and the structure light are used to match the 3D object surface data. A new ladder-shaped calibration block is designed and two images are taken: one is structured stripe image and the other is laser plane image by this block. The laser plane and camera calibration can be accomplished by both images.

由于关节式坐标测量机的激光测量头，使用单摄像机和线结构光来匹配被测物体表面的三维数据，本文设计了一种新型的阶梯形标定块，通过标定块图像和激光条纹图像完成了摄像机的内外参数标定和激光平面参数标定。

This photograph was taken at the launching of a Blue Streak rocket, and shows an oval blob of light near the rocket.

这张照片是在发起一个蓝色条纹火箭，并显示出一个椭圆形斑点的光附近的火箭。

The piecewise function of the relationship between the full width at half maximum of the centre bright fringe and the rectangular aperture width was put forward as well.

给出的中央亮条纹强度半最大值宽度与矩形光阑边长关系的拟合表达式，可为激光应用装置的设计提供理论支持。

For different substances that occur under two different light sources in two different stripes, when the slit mouth gradually Masuda Otsuki reduced, this process will find in the thin section of a gas light appears under the of the color overlay each other like , so that spectra of surface light intensity gradually weakened and finally win only the lower part of the spectrum not being added to the surface occurs, known as:"Bright-Line Spectrum."

对于不同物质在两种不同光源下出现的两种不同条纹，当把狭缝口逐渐増大即缩小，这一过程会发现在稀薄气体光源下出现一段一段的各单色象相互叠加，从而使谱面中光强逐渐减弱，最后只胜下部分沒被叠加到的谱面出现，被称为："明线光谱"。

Okubo,the stress distribution in a circular disk maked of fiber-reinforced photoelastic composite under diametrical compression is investigated.

本文根据Okubo的各向异性分析，对纤维增强光弹性复合材料制成的对径受压圆盘进行了研究，在此基础上提出了采用一个对径受压圆盘测定光弹性复合材料三个条纹值f_L、f_T、f_

Plunder melds and run with this jewel!

掠夺melds和运行与此宝石！

My dream is to be a crazy growing tree and extend at the edge between the city and the forest.

此刻，也许正是在通往天国的路上，我体验着这白色的晕旋。