充填

I found my teacher to have a treatment of 5 of my teeth, fees are more and cures less. In my opinion pulpitis causes the toothache because of no propitiation of my small pulp. That stimulated me and made me uncomfortable. I promise that if some day in the future people ask me for therapy of tooth, as a doctor, I will do my best to relieve pain.

上周找老师看了看牙，花销不少但是牙还是很痛，根据自己感觉好象是因为深龋没有安抚就直接充填导致牙髓激惹了，这样弄的自己的心情也很不舒服，感觉钱打水漂了，以后一定要当个好医生，否则患者会恨死你的，反正我现在就讨厌这样的不负责任，牙齿好痛不说明天还要返工重新看，白花了时间和金钱没有好结果，唉。

Health food shop can produce a hard capsule, soft capsule, tablet, powder, tea agent, granules, preparation of wine, drinks, etc., and the introduction of advanced automatic liquid France Capsule Filling Machine and sealing machine, will be filled with oil-soluble materials to hard Capsule play better absorption and utilization value of effective products improve the safety of stability and preservation of moisture.

保健品车间可生产硬胶囊、软胶囊、片剂、粉剂、茶剂、冲剂、配制酒、饮料等，并引进先进的法国全自动液体硬胶囊充填机及封口机，将油溶性原料填充至硬胶囊中，发挥更好的吸收利用价值，有效提高产品的安全稳定度及防潮保存性。

The experimental results show that the estimated strength of cylindrical specimens and core specimens taken from plate-like specimens under the condition of saturated surface-dry were good and the difference between the estimated strength and the measured strength is within 10%. For the plate-like specimens used in this study, measured the surface P-wave and internal P-wave, and investigate the difference between surface P-wave and internal P-wave velocities. Firstly, the internal P-wave velocity was recovered to the saturated surface-dry condition.

实验结果显示，350 kgf/cm2自充填混凝土及早强混凝土之圆柱试体及版试体所进行波速－强度关系曲线验证结果良好；而将圆柱试体及版试体套入粗骨材含量波速－强度关系式所得结果，其圆柱试体28天超音波强度预估差异约10%，显示试体28天处於面乾内饱和状态，以粗骨材含量配合波速量测来预估强度之结果良好。

Methods: Fourty-five mandibular second premolars with single oval-shaped root canal were prepared with step-back technique and filled with warm vertical compaction technique. The teeth were divided into three groups randomly: ProTaper group, Mtwo group and manual stainless group. The operating time was recorded.

45颗具有椭圆形根管的下颌前磨牙经逐步后退法预备、热牙胶垂直加压充填后随机分为3组，分别用ProTaper再治疗器械和ProTaper器械，Mtwo再治疗器械和Mtwo器械，手用H锉和K锉去除牙胶。

The surface roughness of the SL mold plate does not change dramatically with the increase of the demolding times. As to the defects of injection molded parts, there exists weld line, flow mark and solid skin.

对於SL模具中的高分子材料流动及缺陷生成特性研究，设计了基本的长直平板状流路，以实际射出充填来实验模拟各种条件下平板流路内的材料流动状况。

Silver-colored fillings have been used by dentists for over a hundred years to treat cavities in teeth.

银色充填物已经被牙科医生使用了百年以上，来治疗牙齿的空洞。

The experimental results show that glass powders could effectively decrease the friction coefficient of the composite.

试验结果表明：玻璃粉充填尼龙1010能降低复合材料的摩擦系数，w为25%时摩擦系数最小；w为20%时，磨损率仅为尼龙的18%。

The experimental results show that glass powders could effectively decrease the friction coefficient of the composite.

试验结果表明：玻璃粉充填尼龙1010能降低复合材料的摩擦系数，础为25％时摩擦系数最小；w为20％时，磨损率仅为尼龙的18％。

Using the software, the velocity profile and temperature distribution when the molten metal filling a sheathing board casting with original gating system were numerically simulated, and the mechanism of shrinkage formation was analyzed.

将三维模拟软件应用于球磨机衬板件，采用工厂原有工艺方案，对金属液充填衬板件时的流场及温度场进行了数值模拟，分析了铸件中产生缩孔缺陷的原因。

The full tail sand grouting filling system at zhangmatun iron mine is to adopt tailings after two stage dewatering from washing plant,make homogeneous grouting filling material with high density from mixing full tail sand,cement and water through stirring and form bulk and low grade grouting body with strong solidity,filling in gob taking pipe full self-flowing transport way.

马屯铁矿全尾砂胶结充填系统采用选矿厂两段脱水后的尾矿，通过搅拌将全尾砂与水泥、水混合制成高浓度均质胶结充填料，以管道全自流输送方式充入采空区，形成整体性强的大体积低标号胶结体。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐