充填

Analyzing the deformation and failure characters of different backfills, their damage constitutive equations investigated with damage mechanics whose calculating results coincide with experiment results well were proposed.

分析了不同配比充填体变形与破坏特征，用损伤力学建立了4种不同配比充填体损伤本构方程。

According to experimental results of four kinds of cemented backfills with the ratios of cements to tailings 1:4, 1:8, 1:10 and 1:12, the laws of three-dimensional energy dissipation of backfill are presented during the course of breakage.

根据灰砂配比为1：4，1：8，1：10和1：12的4种胶结充填体力学试验结果，揭示不同配比充填体三维损伤耗能规律。

The simulation results show that the asymmetry structure of the ratchet die cavity influences the BMG's flowing behavior greatly. During the material filling tooth cavity, dead zone volumes exist and situate on the areas with sparse teeth distribution. The full filling or not of the ratchet tooth tips, as the final filling region of the forming process, determines the super-plastic forming quality. Adopting smaller punch speed or longer load holding time is necessary for full filling of the tooth tips.

研究结果表明，棘轮模腔结构的不对称性对材料的流动行为影响显著；在材料向齿形的充填过程中存在流动死区，死区的位置处于齿形分布较稀疏的部位；齿形尖角是成形的最后充填部位，在终成形阶段采用较小的压下速度或较长的保压时间，有利于齿形尖角的完全充满。

The results show when formations contains a single vertical parallel fracture system, the amplitude of reflected P-wave is more sensitive than velocity for different infillings of vertical fractures; the anisotropy increases as fracture density increasing; the anisotropy of gas-bearing fracture is stronger than the fracture saturated with fluid.

研究结果表明，当地层中含有单组垂直的平行裂隙时，反射P波振幅对垂直裂隙中充填物的敏感性大于速度对裂隙中充填物的敏感性，随着裂隙密度的增加，P波各向异性程度也相应增强，裂隙中含气时，各向异性程度较含饱和水时强。

Group 2:the success rate of glass ionomer silver reinforced restorative group was 90%,that of glass ionomer group was 75%.

非创伤性充填技术是修复老年人后牙根面龋较理想的方法，银粉玻璃离子是较理想的充填材料。

One side was filled by glass ionomer silver reinforced restorative,and another was glass ionomer.

选择60例老年患者为试验组2，应用非创伤性充填技术，双侧分别用银粉玻璃离子和玻璃离子直接充填。

As to multi-layer reservoirs,each layer can be divided into three areas:area of gravel-packing,area of perforation and area of radial flow.Each area has its own governing equaiton and the solution is expressed by Green function.The well bore pressure and layer-rate is given through Green function in Laplace space.The pressure drop and skin factor isobtained also in each area.

根据多层砾石充填完井的渗流特点，将每个产层在径向上分成3个区域，即砾石充填区、射孔区、地层径向流区，每个区域有各自的渗流方程，对n层油藏有3n个渗流方程，将每个区域的方程用Green函数来表示，由各层的Green函数得到井筒混合压力、分层压力及分层产量在Laplace空间上的解，最后得到每层各区域的压力损失、表皮系数以及井底压力和分层产量与时间的变化关系。

Because the direct roof of the No.92 ore-body is the backfilling of the No.91orebody which is the cementing materials or non-cementing materials, and there are no-filled mined-areas in someplace. So there are large-scale hidden troubles on the top of the No.92 slowly inclined large and thick ore-body, then we must find a new mining technology which aims at the complex mining condition of the No.92 ore-body. The cutting nature of the No.92 ore-body is very poor, so choosing the rational drilling and blasting parameters and enhancing the overall technological economic benefits are also the urgent problems waiting to be solved in the exploitation of the No.92 ore-body. The No.92 ore-body, thin lodes and the exploitation process of the No.91orebody influence each other, the geo-pressure phenomena aggravates obviously in case of the mined-areas increase constantly, and the geo-pressure problem will be more and more serious when the No.92 ore-body be exploited on a large scale in the next step.

由于它的直接顶板就是开采91号矿体时的胶结或者非胶结的空区充填体，部分地段甚至是未充填的采空区，使92号缓倾斜厚大矿体的上部形成大范围的隐患区，因此，必须针对92号矿体复杂的开采技术条件，寻找新的采矿技术与工艺。92号矿体的可凿性极差，选择合理的凿岩爆破参数，提高凿岩爆破工作的总体技术经济效益，也是92号矿体开采急待解决的问题。92号矿体与细脉带、91号矿体开采相互影响，目前在采空区不断增大的情况下地压显现有明显加剧的趋势，在下一步92号矿体大规模开采时，地压问题将越来越严重。

In this paper, the author applied mutation theory in determining toppillar critical size in sub level mined and post filled area, and provided important value for making post minging and filling plan.

利用突变理论确定深部铜矿分段空场，嗣后充填地段的顶柱临界尺寸，为后期编制采矿和充填作业计划提供理论依据

The method locates with Raypex5 root needle appearance has a tooth to 205 in all 403 roots canal undertakes length of root canal job is measured, after undertaking with this length the root is in charge of provision to fill up, film X line piece the quality that observes root canal fills up.

方法用Raypex5根尖定位仪对205颗患牙共403个根管进行根管工作长度测量，以此长度进行根管预备充填后拍摄X线片观察根管充填的质量。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐