允许误差

In this paper, we construct the indiscernibility set of by defining the toleration relation on the continuous condition attribute and realize the partition of the universe by analyzing the decisions of the objects in the indiscernibility set of .

本文通过定义连续值域信息系统上系统误差允许范围内的相容关系，构造了对象的不可区分集。

The cumulative distribution of the ABI measured by the two methods demonstrated that the differences among them were not homogeneously distributed across the range of ABI value. The Doppler and oscillometric ABI readings were similar below values of 0.9, at values between 0.9 and 1.16 ,the readings were nearly the same line, whereas at values exceeding 1.16, the readings were not parallel.

5多普勒法与示波法测量所得ABI值结果之差均数为0.009(95%CI -0.24～0.2)，非常接近于0，在95%可信区间之外的人数为48例(4.8%)，在误差允许范围之内，表明两者一致性较好，并且这一差值随着ABI值的增加数值逐渐减小(r=-0.09，p=0.002)。

The content of each different single oil of mixed oils could be calculated using the components concentration and diagnostic ratios of normal alkanes and terpane (m/z 191) biomakers of different single oil.

通过运用单种油样的正构烷烃浓度，萜类(m/z191)生物标志物的浓度以及它们的诊断比值作为参数，计算混合原油中的单种原油含量，其误差在允许的范围之内。

Chlorine in the sample solution was indirectly determined by mercury thiocyanate spectrophotometry. The results are in good agreement with those from other methods with precision of 1.74%RSD (n=6) for the sample with 1.08% chlorine.

方法用于实际样品的分析，结果与其他方法测定值一致，误差均在允许范围内；对氯含量为1.08%的样品重复测定6次，精密度为1.74%。

The testing method and allowed tolerances should be

测试方法和允许的误差必须显示。

We can make full use of the time series by extending the permitted range of angle errors.

这主要是通过扩展角度误差的允许范围来提高有限的实验数据的利用率。

In an admirable error bound, the numerical simulation had the close results with experiment by the characteristic curve of cold mass flow fraction, as well as Thermodynamics model of vortex tube, So Thermodynamic theory hypothesis was available to explain Ranque-Hilsch effect of vortex tube.

在误差允许的范围内，涡流管冷流率特征曲线描述的结果与涡流管热力学理论给出的结果非常相近，说明涡流管热力学理论假设能够描述Ranque-Hilsch效应。

The usual trade margins or allowance in quality in the country of production are to be agreed upon by Buyer.

生产国对于质量通常所允许的贸易误差，须经卖方同意

Mosaic panels (such as turning the table, with KD in the table board, etc.), flatness error allowed in the soil between 0.4mm.

拼接面板（如翻板桌、附KD中板的餐桌等），平面度误差允许在土0.4mm之间。

For example, size problem to offsctdruckereien point of view, the greater the number of celebrity…, the better, because the same set of products can be more, and flexography is not, efficiency depends on the machine speed, in parts of the appropriate size, size 小意 to use low-cost, small size, from roll to die-drum is plate, tape, seihan fees naturally had; size also means that the cumulative operation error gets smaller, quality control is easy.

譬如尺寸问题，以胶印的观点则是开数越大越好，因为同样印数下可以多出产品，而柔版则不然，效率是靠机速实现的，在活件允许的情况下，尺寸适当即可，尺寸小意着使用成本低，试想，尺寸小则从版辊到模切滚筒都小，版材、胶带、制版费自然也就都省了；尺寸小还意味着操作过程中的累计误差变小，质量控制也就容易了。

The absorption and distribution of chromium were studied in ryeusing nutrient culture technique and pot experiment.

采用不同浓度K2CrO4(0，0.4，0.8和1.2 mmol/L)的Hoagland营养液处理黑麦幼苗，测定铬在黑麦体内的亚细胞分布、铬化学形态及不同部位的积累。

By analyzing theory foundation of mathematical morphology in the digital image processing, researching morphology arithmetic of the binary Image, discussing two basic forms for the least structure element: dilation and erosion.

通过分析数学形态学在图像中的理论基础，研究二值图像的形态分析算法，探讨最小结构元素的两种基本形态：膨胀和腐蚀；分析了数学形态学复杂算法的基本原理，把数学形态学的部分并行处理理念引入到家实际应用中。