偏心

This paper analyzes the moving characteristics of nipper mechanism of new type FA266 comber made in China, and discusses the eccentric shaft and eccentricity influence on combing process ing and the moving of nipper mechanism, which provides the theory basis of the from of opening-closing time adjusting mechanism, dimension, process parameter, and adjustment pattern.

分析了国产新型精梳机FA266钳板机构的运动规律，讨论了偏心轴偏心距对精梳工艺及钳板机构运动的影响，为确定国产新型精梳机中钳板运动的开闭口定时调节机构的形式、尺寸、工艺参数及调节方式提供理论依据。

We transformed eccentric coaxial line cross-section into rectangular area by hyperbolic cotangent transformation, transformed the FDTD difference expressions into CM-FDTD difference formula, calculated the cutoff wavenumbers of higher order TE and TM modes in eccentric coaxial line.

本文用双曲余切变换将偏心同轴线截面变换为矩形区域，相应地将FDTD差分格式变换为保角变换FDTD差分格式，计算了偏心同轴线TE、TM高阶模的截止波长。

According to the structure and motion characteristics of the spherical offset mono-cone bit, compound cylindrical coordinates were set up, and basic geometric equations and the conditions of teeth to penetrate rock for the bit were presented.

针对偏心单牙轮钻头的结构和运动特点，利用复合圆柱坐标系统的基本原理，建立了偏心单牙轮钻头几何学基本方程和牙齿对岩石的吃入条件。

Due to the effect of torsional vibration arose by eccentricity of the center of mass and the center of rigidity, there will produce stress concentricity in some local location of the structure, which is very detrimentally. This paper discussed the contribution of the reduction of the response of torsional vibration of the accessorial eccentrically braces in structure on emphasis.

由于不规则高层建筑的质心刚心偏心而引起的扭转振动效应，会使结构的局部产生应力集中等极为不利的情况，因而本文着重讨论了增设偏心支撑后的结构，对减小原结构的扭转振动效应的贡献。

To beam-column structure, a formula can calculate distortional buckling load .

在实际中荷载小偏心在所难免，在荷载小偏心的影响下构件还会发生畸变屈曲。

In strictly, it is hard to make the light normal incident into the sphere, double refraction will take place in crystal sphere when a TEM〓 mode Gaussian beam oblique incident into the sphere, and the two orthogonal polarized beams are both elliptical Gaussian beam. The ellipticity and eccentricity of the elliptical Gaussian beam will change with the incident angle, and for a fixed incident angle, they will change with the shifting of incident beam waist position.

由于严格意义上的正入射较难实现，基模圆高斯光束斜入射晶体球后将在球内产生双折射，且球内偏振态正交的两束折射光都将是椭圆高斯光束，它们的椭圆度e和偏心度Δ随入射角的改变而改变，在入射角一定的情况下，入射光束束腰的移动也将改变这两束折射光的椭圆度e和偏心度Δ。

Before driving under the exciting force to be checked at both ends of the two vibrators fixed eccentric block, adjustable eccentric angle is the same as the block to check whether the fasteners completely secure fastening; inspection of electrical wiring and insulation is good .

开车前应根据激振力的要求检查两振动器两端固定偏心块、可调偏心块的夹角是否完全相同，检查紧固件是否完全紧固牢靠；检查电气接线及绝缘度是否良好。

The air flow excitation force of leaf peak clearance evocable by impeller eccentricity is the important part of the air flow excitation force, so the research of it is very important too.

而由叶轮偏心引起的叶顶间隙气流激振是气流激振的一个重要方面，因此，加强透平机械中由叶轮偏心引起的叶顶间隙气流激振的研究也显得非常重要。

The one-side electronic extensometer fastened on only one side of tensile specimen cannot eliminate the effect of bend of eccentric tension. The results of measurement of such electronic extensometer are instable and then more errors may be included.

目前，国内外使用的电子引伸计多数是测量拉伸试样单侧的变形，由于拉伸试样往往发生偏心拉伸，单侧测量的引伸计无法扣除偏心拉伸的影响，因而其测量结果极不稳定和产生比较大的误差。

By means of Furrier decomposition the harmonic components in various orders are obtained, and then the induced electromotive force in stator winding is obtained when the air gap eccentricity of turbo-generator is taken into consideration.

通过傅里叶分解得到了各次谐波分量，在考虑气隙偏心的情况下得到了定子感应电势，理论推导证明偏心对定子绕组感应电动势并不产生影响。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。