英语人>网络例句>倒棱 相关的搜索结果
网络例句

倒棱

与 倒棱 相关的网络例句 [注:此内容来源于网络,仅供参考]

Fruit obovoid, 5–6 × ca. 5 mm; dorsal and intermediate ribs filiform, closely spaced; lateral ribs broadly winged, wings ca. 1.5 mm wide, wider than width of mericarp body; vittae filiform, extending almost the length of the mericarp body, solitary in each dorsal furrow, 2 in each lateral furrow, 2–6 on commissure.

果倒卵球形, 5-6 *约5毫米丝状的背棱和中间棱,间隔紧密;侧棱具宽翅,翅约1.5毫米宽,宽于分果爿身体的宽度;油管丝状,几乎延长至分果爿身体的长度,1在每背面棱槽,2在每侧面棱槽,2-6在合生面上。

Seeds obovoid or obovoid-elliptic, base rostrate, abaxially 1-furrowed with a rounded or suborbicular or elliptic chalazal knot, adaxially 2-furrowed; endosperm M-shaped in cross-section.

种子倒卵球形或倒卵球形的椭圆形,基部具喙,背面的1棱槽具一圆形或近圆形的或椭圆形种脐,正面2棱槽;横截面的胚乳M形。

7 Month blossoms, beautiful sheet is unripe, bury is in lotus Cong Zhong, do not have beautiful Ting or provide; of short beautiful Ting to luxuriant piece 1, calyx of line form; appears prism state, grow 4-5 millimeter, provide corollaceous white of apparent; of 5 green arris or pink, diameter 5 millimeter, laryngeal amaranth.

叶不明显二型,外层卵状披针形或卵形,长2-3毫米,内层线形或倒窄披针形,与外层叶等长。5~7月开花,花单生,埋藏在莲座丛中,无花葶或具短花葶;苞片1枚,线形;花萼似棱柱状,长4-5毫米,具明显的5条绿色棱;花冠白色或粉色,直径5毫米,喉部紫红色。

Stylopodium short-conic. Fruit obovoid to subglobose, slightly flattened dorsally, densely hirsute and velutinous; ribs all corky-winged, equal or lateral ribs slightly broader than the dorsal; vittae 1–3 in each furrow, 2–6 on commissure.

花柱基短圆锥状果倒卵球形到近球形,背面稍扁平,密被长硬毛和茸毛;棱全部木栓质的翅,等长或侧棱稍比背侧宽的;油管1-3在每棱槽,2-6在合生面上。

The automatic control and the velocitymodulation systemofchamfering machine involve programmable controller,DC speed regulating system,frequency converter and the electronic cam switch .

倒棱机的自动控制与调速系统涉及可编程控制器、直流调速系统、变频器、电子凸轮开关等自动化设备,这些自动化设备之间协调配合非常重要。

Series of bevellers are hydraulic pressure drove, equipped with hard alloy cutter.

系列倒棱机床,采用液压自定心夹紧,液压可转位挡料器挡料,硬质合金刀切削。

This articls mainly introduces material selection and geometrical parameter determination for cuttery, cuttery design for coated fine turning, especially the effect of chamfered edge on cutting tool's life expectancy.

文中主要介绍刀具的选材。刀具几何参数的确定。涂层。精硬车削的刀具设计,特别是刃口倒棱对刀具寿命的影响。

Addition of chamfering shape on seating surface of joint bolt at atf cooler pipe area.

倒棱增加物的塑造在自动制冷管的范围内、接头螺栓的座套表面。

Chamfering machine is the special equipment for pipe-end processing.

倒棱机是钢管端面加工的专用设备。

By analysis and comparing with other kind of control system, according to the demands of the servo system for the Chamfering machines, the servo cylinder of the system was designed, the parameters of the opponents that was used for control and feedback in the system was calculated. Finally, the mathematics model of the position-feedback system was established, according to the model, the simulation frame was provided.

根据倒棱机对伺服控制系统的要求,通过分析及与其它控制系统的比较,设计了电液伺服系统的伺服油缸,确定了电液伺服系统控制及反馈元件性能参数,最后建立了位置控制闭环反馈系统的各个环节数学模型,并在此基础上绘出了伺服系统传递函数框图。

第2/4页 首页 < 1 2 3 4 > 尾页
推荐网络例句

The concept of equivalent rotationally rigidity is offered and the formula of rotationally rigidity is obtained.

主要做了如下几个方面的工作:对伸臂位于顶部的单层框架—筒体模型进行分析,提出了等效转动约束的概念和转动约束刚度的表达式。

Male cats normally do not need aftercare with the exception of the night after the anesthetic.

男猫通常不需要善后除了晚上的麻醉。

Its advantage is that it can be used in smaller units.

其优点在于可以在较小的单位中应用。