保护设备

Following aspects are specially discussed:(1) In-situ study on the mechanism and the rate determining step of corrosion processes at the interface between metal and corrosion media;(2) Reliability of structures in corrosive environment;(3) In-situ non-destruction corrosion inspection, evaluation, repair and maintenance of engineering structures;(4) A new approach for material selection-life cycle costs, LCC;(5) Terotechnology;(6) Corrosion protection and environmental protection;(7) microbiologically influenced corrosion;(8) Computer aided design of corrosion protection;(9) Corrosion and protection of reinforced concrete structures;(10) Corrosion and protection of marine structures;(11) New development of coating and corrosion inhibitor etc.

论述了腐蚀科学与防护技术几个值得注意的发展动向，它们包括：(1)金属／腐蚀介质界面反应及其快速步骤的原位研究；(2)在腐蚀环境中结构的可靠性；(3)腐蚀的在线无损检测／评价和设备的维修保养；(4)材料优选的新方法－LCC；(5)防护系统工程学；(6)腐性防护与环境保护；(7)微生物腐蚀；(8)腐蚀防护的计算机辅助设计；(9)钢筋混凝土结构的腐蚀防护；(10)海洋工程结构的腐蚀防护；(11)防护涂层和缓蚀剂的新发展等。

Coating: It is widely used for the coating of multifarious electric components, semi-conductor equipment, the industrial electric apparatus and equipment for insulation, moistureproof, shockproof and protection.

涂覆：广泛地用于各种电子元件、半导体器材和工业电器设备的涂覆。起绝缘、防潮、防震和保护作用。

Jin Shui HighSPEED Mill Power Producing System can make the differdnt molal structures mate rials powderfor 20 eyes to 80eyes in common temperaeure, These materials are differdnt kinds of soft hard PVC 、PP、PS; thosecan change its nature such as PP、TEP、 PS、 PA、 PC ,etc; non-plastic such as dee rhm, timber, leather and palm oil shells, etc,Especially suit for raw material of plastic to chang its naure, paints of mother colour tofill up , paints, tec .During the working process, firstly put the quantitative and well-distrib uted rawmaterialsun to the Moll Box by the Hopper, them put the powder out of the Moll box by Auto loader, finallysirfand retrieve the powder through sifting machine .If someofthe have not milled well , you can do itagain As a matter of fact, it will be as excellent as the mew plastic and can keep every normof the munchang eablein their function of chemistry and physicsafterusing about 30% of power mixed up with 70%raw mate rials of plastic. So the machines if helpful of plastic businessman to save money and good for protecting our environ mentathe same time

金穗JS 系列高精密磨粉生产系统能在常温下将各种的软硬：PVC、 PP 、PS 及改性PP 、PS 、PA 、PC 等不同分子结构的及非塑料类如（鹿角、木梢、皮革及棕油壳等）材料磨制成20目~80目粉末状，适合塑料原料改性，色母料填充涂料、塑纺织的涂料、地毯背面涂料、制药等加工行业，这些颗粒原料通过定量的加料器均匀地送进磨箱中，再由吸风机将磨好的粉末吸出磨箱经过筛选机筛选回收，如较粗的颗粒再次被送进磨箱中进行粉磨，这些材料经过我们特殊改良刀齿，创新突破来配合日新月异原材料组合使用，经塑料制品厂商实践证明在其产品原料中加入磨制粉体30%左右使其更好塑化且其制品的化学，物理性能保持全新料的各项指针不变，因此是塑料厂商降低成本且同时有利于保护环境的粉磨回收设备。

In Shui HighSPEED Mill Power Producing System can make the differdnt molal structures mate rials powderfor 20 eyes to 80eyes in common temperaeure, These materials are differdnt kinds of soft hard PVC 、PP、PS; thosecan change its nature such as PP、TEP、 PS、 PA、 PC ,etc; non-plastic such as dee rhm, timber, leather and palm oil shells, etc,Especially suit for raw material of plastic to chang its naure, paints of mother colour tofill up , paints, tec .During the working process, firstly put the quantitative and well-distrib uted rawmaterialsun to the Moll Box by the Hopper, them put the powder out of the Moll box by Auto loader, finallysirfand retrieve the powder through sifting machine .If someofthe have not milled well , you can do itagain As a matter of fact, it will be as excellent as the mew plastic and can keep every normof the munchang eablein their function of chemistry and physicsafterusing about 30% of power mixed up with 70%raw mate rials of plastic. So the machines if helpful of plastic businessman to save money and good for protecting our environ mentathe same time

S 系列高精密磨粉生产系统能在常温下将各种的软硬：PVC、 PP 、PS 及改性PP 、PS 、PA 、PC 等不同分子结构的及非塑料类如（鹿角、木梢、皮革及棕油壳等）材料磨制成20目~80目粉末状，适合塑料原料改性，色母料填充涂料、塑纺织的涂料、地毯背面涂料、制药等加工行业，这些颗粒原料通过定量的加料器均匀地送进磨箱中，再由吸风机将磨好的粉末吸出磨箱经过筛选机筛选回收，如较粗的颗粒再次被送进磨箱中进行粉磨，这些材料经过我们特殊改良刀齿，创新突破来配合日新月异原材料组合使用，经塑料制品厂商实践证明在其产品原料中加入磨制粉体30%左右使其更好塑化且其制品的化学，物理性能保持全新料的各项指针不变，因此是塑料厂商降低成本且同时有利于保护环境的粉磨回收设备。

The automation constant temperature controls system , the automation liquid place controls system , the automation eliminates bubble navar , automation pressure protects system and excellent allocation , ensures that equipment high-performance works.

自动恒温控制系统、自动液位控制系统、自动消泡控制系统、自动压力保护系统以及精良的配置，保证设备高性能运行。

In the electric power profession, Ortho provide automated control system and instruments as well as in the cement profession.

在电力行业，昊图提供变电站自动化系统综合保护系统及相应仪表。在水泥行业，昊图提供控制系统、变频设备和仪表。

When the maglev train is running, the speed and position detection sensors are affected by the shake of the train and the joint of long stator track, also the size of the joint is different, which can badly affect the signal of the sensors in speed and position detection system. This can cause overcorrect or overvoltage protection in traction system and even can damage the traction equipment.

磁浮列车测速定位传感器在实际运行时，会受到列车震动和长定子轨道的接缝等影响，并且轨道接缝的尺寸也不相同，使得位置传感器在通过不同轨道接缝的时候产生不同的信号畸变，导致牵引设备过流或过压保护甚至烧毁。

Risk and maneuverability analysis on engineering design is widely used to conduct security appraisal abroad. The potential risks might be caused by technical parameter deviation, failure and faulty operation of facilities and pipelines in the system were normally analyzed along with the reason why deviation and faulty operation occurred. The acceptable risk was then appraised according to the results, reasons and designed protective facilities. Later, the security countermeasures and solutions were brought forward purposively to further modify and refurbish the security design and operation management.

国外广泛应用危险与可操作性分析对工程设计进行安全评价，分析系统中装置、设备、管道的个别部分工艺参数偏离、故障或误操作引起的潜在危险，分析偏离、故障出现的原因，根据后果、原因和已设计的保护装置，评估可接受的风险，并有针对性地提出安全对策和措施，用以指导修改、完善工程的安全设计和操作管理。

The CIM's front panel contains red, amber, and green LEDs that indicate breaker trip coil operation, trip signals and their sources, and the status of both the external reclose relay and the interface to the supervisory control system. Taking up less than 13 square inches of panel space, the unit is easily incorporated into a new or existing substation and is compatible with virtually all other electronic or electromechanical protective equipment.

一个简单的8位平行接口也是可利用的， CIM 面板包含以显示开关线圈操作、报警信号及信号源，重合继电器和连接到监控系统的状态，、它占了不到3平方英寸盘区空间，单位很容易被合并到一个新的或现有的变电站并且与其他几乎所有的电子、机电设备的保护兼容。

Machining process and general information:· General Information – Tooling o Plan to have own engineering group as company expands o Hwasung is subcontracted to do engineering currently o Uses same cutting tools as in Korea facility – all diamond o Regrind tools if can o Hwasung has capability to surface grind, repair dies, and make molds with wire EDM process · General Information – Machining o Boundary samples are used: okay, borderline, not good o Quality room has separate windows for incoming and outgoing parts o New equipment will be coming in from FM LaGrange plant o Each operation has pictures and job instructions for what to check and which gage to use to check part o Parts are manually loaded into machine or pallet, depending on line o Auditor checks parts for verification: after operator checks part, puts in bin, auditor checks part and reloads back on line o Have tool management system o A pokeyoke check is used for orientation prior to loading o Machines are guarded o Mostly have CNC machines o Manual chip collection systems o If automated, have robots with grippers to load/unload parts from pallets o After final inspection, operator visually inspects and loads onto plastic dunnage with the crown up and loads into the washer o Repairs: filing down of burrs or sharp edges after anodizing the crown o Have 2 Excello machines for special machining of the pin bores o 2.7% scrap for gasoline pistons o Cycle time is 18 seconds for gasoline piston o Process – Wash o Spray system o 4 stations: heated wash, wash with degreaser, 2 rinse stations o Uses RO water o Operator blow dries piston and puts on dunnage with crown up o Parts wheeled into coating room o Needs major improvements here o Chemical analysis done for bath in chemical room o Comments/Observations: o Relatively small piston facility, but plans for additional space.

加工工艺和一般信息：·–的一般信息工具 o 有自己的工程集团，随着公司的扩展计划 o Hwasung 是分包做当前工程 o 用途相同的扦插工具，如在韩国设施–所有钻石 o 回收料工具如果可以 o Hwasung 已表面研磨，修复模具，和模具丝电火花加工能力过程·一般信息–加工 o 界限示例用于：好交界，不好 o 质量房间有单独的窗口传入和传出的部件 o 新设备会在来从调频拉格朗日植物 o Each 操作具有图片和工作说明的什么复选，计为使用检查部分 o 部件是手动加载到机器或托盘，取决于行 o 审计检查验证零件：置于 bin，运算符检查部分后，核数师检查部分并重新加载回行上 o 有工具管理系统 o 为 pokeyoke 复选用于在加载之前的定位 o 机被保护 o Mostly 有数控机床 o 手动芯片收集系统 o 自动，如果有与要加载/卸载部分从托盘 grippers 机器人 o 后最终检验，运算符将直观地检查并加载到与塑料衬垫冠了与到洗衣机负荷 o 修复：提交下毛刺或锋利的阳极氧化冠后 o 有 2 Excello 机特别加工的销孔 o 2.7%废料的汽油活塞 o 周期时间是为汽油活塞式 18 秒 o 过程–洗 o 喷射系统 o 4 站：加热洗、与脱脂剂洗、 2 冲洗站 o 使用反渗透水 o 运算符吹干活塞式并将了放冠衬垫 o 部件轮式进涂层房间 o 需要重大改善在这里 o 为在化学的房间里浴做的化学分析 o 注释/结论： o 相对小活塞式设施，但额外的空间的计划。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐