使润滑

A new infinite gas-lubiicated journal bearing with active controlled restrictor is proposed in order to remedy the defects of several existing infinite stiffness at abroad in construction, manufacture and adjusting, which combining surface-restriction with active controlled restriction, make the static and dynamic effect both better.

针对目前国外几种无穷静刚度气体润滑轴承结构复杂、制造难度大、调整困难的不足，本文提出了一种主动控制节流无穷静刚度气体润滑轴承，将表面节流与主动控制节流相结合，使轴承动、静压效果同时获得较好的发挥；利用浅腔及锯齿形多槽结构产生较强的楔形动压效应，提高轴承的静态和动态性能；利用主动控制节流器对轴承进行压力反馈主动控制，提高轴承的承载力、刚度，并在一定载荷范围内，使轴承刚度为无穷大。

Bearing is calorific, make grease gently attenuant leakage, damage bearing again, cause pecuniary loss to the user.

轴承发热，轻则使润滑脂稀释漏出，重则将轴承损坏，给用户造成经济损失。

It was the interactional result of electronegative double bond and branched chain with positive induction effect and space steri.

研究发现，加入不同的添加剂使润滑脂的油膜强度、锥入度和滴点产生不同的变化，并对其产生的原因作了机理分析，认为是由于极压抗磨添加剂分子中带负电性的双键和带正诱导效应及空间位阻效应的支链共同作用的结果。

In the grease is added to ceramic type particles,"this will be the base oil components are connected together as like a chain, so that the performance of grease stronger."

在润滑脂中添加的是陶瓷类微粒，"由此将基油中的成分像链条一样地连接起来，从而使润滑脂的性能更强"。

The effect of tribology factors on bearing vibration is studied experimentally. AR model and WPT are used to processing the normal arid abnormal signals. The results are as follows:1. The vibration of ball bearings is caused by the tribology action of contact pairs of ball and ring races and has the essential of tribo-dynamics. Any factors affecting the tribology characteristics of contact pairs will affect vibration and noise of bearings consequently.2. Vibration characteristics of bearing keep almostly unchanged with the increasing of axial load expecting the increasing of nature frequencies. When radial load increasing with axial load unchanged, nature frequencies keep unchanged but some new vibration peaks appears in the spectrum.3. Vibration amplitudes are damped and nature frequency are enhanced with sufficient lubrication. Vibration and noise of bearings increase obviously and roar can happen and the contact surfaces scratch slightly under insufficient and unclean lubrication state. Bearing will be disabled in a few minutes without any lubrication.4. Bearing vibration is unstable under low speed. With the speed increasing, the vibration become stable and natural frequencies increase slightly but the amplitudes increase apparently.5. Bearing vibration can be excited only by some harmonics ofwaviness without lubrication and by all harmonics with lubrication based on the theoretical analysis.6. The nature frequencies of ball bearings decrease with the increasing sizes. When international clearance increasing, nature frequencies decrease in radial and increase in axial and angular and the amplitudes increase in radial and decrease in axial and angular. When the number of balls increasing, nature frequencies increase and amplitudes decrease. When the pitch diameter increasing, axial nature frequency increase and others nearly keep no change. When outer race groove curvature radius increasing, nature frequencies increase in radial and decrease in axial and angular and amplitudes keep no change in radial and increase in axial and angular. When inner race groove curvature radius increasing, nature frequencies decrease and amplitudes increase.7. The distortion in amplitude and frequency components of bearing vibration signals picked up by the present probe measurement method is founded and right conclusions cannot be achieved by the signals. When accelerometer is rigidly screwed with steel stud onto a flat outer surface of a ball bearing, vibration signal can be got without distortion and the reliability of research on bearing vibration is assured.8. AR model is suitable for large samples of bearing vibration signals, square root of length of samples can be used as the upper limitation of order determination and the FPE order selection criterion is effective. Many advantages of AR spectrum are founded over the classical based on FFT.9. Time-Frequency analysis is necessary for abnormal noise of ball bearings. WPT overcomes the principle shortcomings of STFT and proved to be a best tool to process the abnormal signals.

理论分析和试验研究表明： 1球轴承振动是钢球—滚道接触副中的各种摩擦学作用引起的，具有摩擦动力学的本质，任何对接触副的摩擦学特性有影响的因素都将对球轴承的振动和噪声特性产生影响； 2中心轴向载荷作用下，载荷增大使球轴承的固有振动频率升高，载荷越大同样的载荷增幅引起的频率升幅减小，足够大的中心轴向载荷作用下载荷的变化对球轴承振动的频率特性不会产生明显的影响； 3轴向和径向联合载荷作用下，径向载荷不大时球轴承振动的固有频率基本不变，但是可能引起变刚度激励的非线性振动，出现新的频峰，过大的径向载荷将使部分钢球脱离接触，使球轴承的振动和噪声呈现不稳定状态； 4润滑对球轴承的振动和噪声特性有重要的影响，良好的润滑对振动有明显的抑制作用，润滑不充分时，振动和噪声的水平会有明显增高，一定条件下还会激发接触副中的谐振，发出啸声，造成接触表面的伤害，无润滑干接触时，短时的运转就会损伤接触副表面，使振动和噪声迅速增大，并随时可能引发严重的磨损和卡滞失效；接触副润滑良好时，油膜的"刚化效应"使球轴承振动的固有频率有所提高，润滑剂中含有弥散性污浊时，振动的幅度总体升高，但弥散性污浊不会改变球轴承振动的频率特性；浙江大学博士学位论文：球轴承振动的研究 5低速时，球轴承振动的基本特征呈现不稳定状态，随着转速的提高，球轴承振动的频率特性趋于稳定，固有频率频峰升高； 6理论分析表明，干接触时钢球和滚道表面波纹度的某些谐波分量能激励球轴承的振动，振动的幅值与谐波幅值成正比，实际球轴承中钢球的分布不可能完全均匀，波纹度的激励作用会随时发生；润滑接触的分析表明，波纹度的任意谐波分量均能激励球轴承的振动； 7球轴承的几何和结构参数分析表明，球轴承尺寸越大，径向、轴向和角振动的固有频率越低；钢球中心圆直径增大，球轴承的径向和轴向振动的固有频率基本不变，角振动的固有频率有所上升，振动的幅频特性基本不变；径向游隙加大使球轴承的径向振动固有频率降低，轴向和角振动的固有频率有所升高，径向振动幅频特性的幅值升高，而轴向和角向降低；钢球的数量增多使球轴承振动的固有频率上升，幅频特性的幅值下降，径向振动的幅值下降最为明显；外圈沟曲率半径系数增大使球轴承径向振动的固有频率升高，轴向和角振动的固有频率降低，径向幅频特性基本不变，轴向和角向幅频特性幅值升高；内圈沟曲率半径系数增大使径向、轴向和角振动固有频率均下降，振动幅频特性的幅值均有升高； 8试验对比表明，传感器采用探针式安装时，由于探针接触副接触特性的影响，钡(量得到的球轴承振动信号有失真，采用专门设计和制作的试验球轴承，以固定式安装加速度计，首次测量得到了球轴承振动的真实信号，通过对振动信号的分析，验证了球轴承振动的理论模型； 9)基于时间序列分析的AR模型适用于大样本球轴承振动信号的分析，以样本长度的均方根值作定阶上界，FPE做判阶准则，给出的AR谱光滑，频率分辨率高，是球轴承振动分析的简便而可靠的手段； 10以时频域分析的小波包变换分析球轴承异音信号能够比较好地定位和聚焦异音发生的时间，时间间隔，频率范围，同样是球轴承振动分析的可靠的手段，可用作球轴承故障诊断技术。

In order to prove this point, Ratchet inferior lubricative solenoid valve core, manually put it on the oil lubrication, at which point it can be seen rising oil pressure drop, and exceeded the original value; successive pressing the lubricating oil pressure of the solenoid valve, can rise to 0.4 or even more, not by this confirmation oil pressure rise and oil pump surface temperature is too high because the machine cannot be automatically put oil lubrication.

为了证实这一不面，用起子底下润滑电磁阀的阀芯，手不静使其不收油润滑，此时可见油压回落后即上落并超功本来值；不断众次按不静润滑电磁阀后，油压竟可上落至0.4甚至以上，由此不否认油压落不矮和油泵暗地温度功矮的来因在于机械不克不及自不静举行不收油润滑所致。

Said invention can conveniently supply oil required for lubrication between the supporting surface of the crankshaft and truss surface of machinef rame to minimize wear and prolong the service life of compressor.

本发明能方便向曲轴的支撑面和机架的桁架面之间供应润滑所需的油，使润滑顺畅，降低驱动负荷，磨损降到最小，可延长压缩机的使用寿命。

Great progress has been made by taking the following technical improvement for the 2500 ton Hydropress: to replace thin oil with lithium grease in its lubricating system; to add four manual grease pumps; to lubricate the four griding parts of the movable beam and the six parts of the column plug sleeves.

通过对2500吨水压机润滑系统改稀油润滑为锂基润滑脂润滑，加装四台手动干油泵，对活动梁四个导向部位和主柱塞压套六个部位实施油膜润滑的技改实践，使1995年较1994年设备完好率提高1。

The assembly of journal and plain bearing liner space is too little, force of organic still oil pressure is small it is the crucial index that affects lubricant result, make lubricate because of lacking engine oil between crankshaft and plain bearing liner and bite dead invalidation, include to be pulled badly, lack lube, layer of alloy of dry attrition generation is fused, grind sliding surface to did not maintain the oily film of certain ply, and all sorts of local overload exhaustion are destroyed, cavitation erosion and V form are destroyed etc, through technology of him director diesel locomotive old experience reachs the analysis of pair of its breakdown reasons, put forward precautionary measures especially. As a result of,the burns caustic mechanism plain bearing liner to burn caustic mechanism of 1 plain bearing liner is the lube film burst between journal and plain bearing liner, cause plain bearing liner and crankshaft generation clash, below high temperature, high pressure and high rotate speed, the wear-resisting alloy layer of plain bearing liner wears away prematurely or fuse, cause plain bearing liner and crankshaft to stick thereby bite, can make the steel back of plain bearing liner and Kong Zhong produces whirligig, inlet port is jammed, carry on the back by steel again with the friction of aperture causes high temperature to make plain bearing liner burned-out further, can cause bolt to break off, happen swing a malign accident that pounds cylinder body of bad internal-combustion engine.

轴颈和轴瓦的装配间隙太小，还有机油压力低是影响润滑效果的关键指标，使得曲轴和轴瓦之间因缺少机油润滑而咬死失效，包括严重拉伤，缺少润滑油，干摩擦产生合金层熔化，磨滑面没有保持一定厚度的油膜，以及各种局部过载疲惫破坏，气蚀和V形破坏等，通过本人主管内燃机车技术多年经验及对其故障原因的分析，特提出预防办法。1轴瓦的烧损机理轴瓦烧损的机理是由于轴颈和轴瓦之间的润滑油膜破裂，导致轴瓦和曲轴产生摩擦，在高温、高压和高转速下，轴瓦的耐磨合金层过早地磨损或熔化，从而引起轴瓦和曲轴粘咬，会使轴瓦的钢背和座孔中产生旋转运动，进油孔被堵塞，再由钢背和座孔的磨擦进一步引起高温使轴瓦烧坏，并会造成螺栓折断，发生甩出捣坏内燃机缸体的恶性事故。

The development condition of constant velocity joint grease, wheel bearing grease,electrical installation bearing grease and electrical contactor grease are intro- duced.

汽车向小型和轻量化的方向发展，很多部件的结构发生了变化，使润滑条件变得苛刻，对润滑脂的耐热性能和长寿命提出更高的要求，介绍了汽车等速节润滑脂，轮轴轴承润滑脂，电装置轴承润滑脂和电触点润滑脂的发展状况。

I didn't watch TV last night, because it .

昨晚我没有看电视，因为电视机坏了。

Since this year, in a lot of villages of Beijing, TV of elevator liquid crystal was removed.

今年以来，在北京的很多小区里，电梯液晶电视被撤了下来。