使显著

The result shows that microbial CA can enhance the total amount of conductible ions and Ca~(2+) concentration by 40% or more, which lead to remarkable driving effects on the corrosion of limestone.

结果表明微生物碳酸酐酶能使灰岩溶出的导电离子总量和[Ca2+]提高40%以上，从而对灰岩有显著的酶促溶蚀驱动作用。

Dealcoholization temperature markedly influences the surface area and porosity of the resultant MAO-supports. When the support was pretreated at lower or higher temperature, the corresponding MAO-support shows very low surface area;2.XRD and IR analyses indicate that MAO has reacted with the residual ethanol in the supports, which is an important manner to get MAO fixed on the carrier. Morever, XPS analyse indicates that MAO can also be coordinated with MgCl_2, which is another way to get MAO fixed on the support;3.ICP and EDX analyses indicate that dealcoholization temperature not only determined the element content on the solid catalyst, but also influences the element distribution on the carrier;4.The activities of the supported phenoxy-imine catalysts and the properties of resultant polymers are strongly dependent on the dealcoholization temperature. The support (MSP-5) obtained by treating MgCl_2·2.56C_2H_5OH at 160℃for 4 h, then modified by MAO is very effective for immobilizing complex 3, the resultant solid catalyst (MSPC-5) shows very high activity in ethylene polymerization, and its kinetics of polymerization is stable during the reaction process. Finally, PEs with spherical morphology and high bulk density (over 0.35g/ml) were obtained, without reactor fouling;5.In this work, polymerization conditions such as alkylaluminums, Al/Zr ratio, temperature and H_2 had a pronounced effect on the activity of MSPC-5 and properties of PE;(3). New MgCl_2-Supported Single-Site Catalysts for Ethylene PolymerizationIn this work, a kind of new MgCl_2 support was obtained by anhydrous MgCl_2 co-milled with solid MAO, and it is a creative contribution. Then some single-site catalysts were supported on the new MgCl_2 support, and the resulted solid catalysts were tested in ethylene polymerization, the results indicated that:1.XRD and IR analyses indicate that MAO does be coordinated with MgCl_2, which is in good agreement with the results obtained by XPS;2.co-mlling time had no obvious effect on the texture of support after 12 hours;3.In this work, MgCl_2 was co-milled with solid MAO for different hours, and then complex 3 was supported on these co-milled supports. It was found that co-milling time markedly influences the activity of solid catalysts, but it had negligible effect on the kinetic profile and the properties of resultant PE.

XPS研究结果表明，MAO不仅仅只和乙醇作用，MAO还与MgCl_2本身有一定的作用，这是一个极为重要的发现；3、通过ICP和EDX表征，发现载体的脱醇温度直接影响着元素在固体催化剂中的含量及分布；4、脱醇温度极大地影响着负载苯氧基亚胺类催化剂的活性和聚合物的性能，特别是原始载体经160℃活化4小时制备得到的固体催化剂MSPC-5的活性明显高于其他脱醇温度条件下制得的固体催化，并且催化剂寿命长，表现出稳定的动力学行为，最终获得了高堆密度(大于0.35g／ml)的球形聚乙烯颗粒；5、本文选择MSPC-5为研究对象，考察了聚合反应参数对催化剂的活性及其聚合物的影响，研究发现：不同的烷基铝对催化剂具有非常重要的影响，特别足TIBA对MSPC-5的助催化活性最高，烷基铝的加入量有一个较佳值，聚合温度为80度时活性最高，H_2的加入使催化剂的活性明显降低且聚合物的分子量也减小；、新型氯化镁载体负载单活性中心催化剂催化乙烯聚合本文创造性采用固体MAO与无水氯化镁直接进行共研磨，制备出了一种的新型的氯化镁载体，并将该载体用于多种单活性中心催化剂的负载化研究，研究表明：1、通过BET、XRD的表征，再次证实了MAO与MgCl_2之间具有直接作用，与XPS的研究结果相一致；2、当研磨时间高于12小时时，延长研磨时间对载体的结构没有显著的影响；3、将配合物3负载于共研磨时间不同的一系列载体上，乙烯聚合结果表明，尽管共研磨时间对负载催化剂的活性具有明显的影响，但是它对聚合物的性能以及催化剂的影响不明显。

Dealcoholization temperature markedly influences the surface area and porosity of the resultant MAO-supports. When the support was pretreated at lower or higher temperature, the corresponding MAO-support shows very low surface area; 2.XRD and IR analyses indicate that MAO has reacted with the residual ethanol in the supports, which is an important manner to get MAO fixed on the carrier. Morever, XPS analyse indicates that MAO can also be coordinated with MgCl_2, which is another way to get MAO fixed on the support; 3.ICP and EDX analyses indicate that dealcoholization temperature not only determined the element content on the solid catalyst, but also influences the element distribution on the carrier; 4.The activities of the supported phenoxy-imine catalysts and the properties of resultant polymers are strongly dependent on the dealcoholization temperature. The support (MSP-5) obtained by treating MgCl_2·2.56C_2H_5OH at 160℃for 4 h, then modified by MAO is very effective for immobilizing complex 3, the resultant solid catalyst (MSPC-5) shows very high activity in ethylene polymerization, and its kinetics of polymerization is stable during the reaction process. Finally, PEs with spherical morphology and high bulk density (over 0.35g/ml) were obtained, without reactor fouling; 5.In this work, polymerization conditions such as alkylaluminums, Al/Zr ratio, temperature and H_2 had a pronounced effect on the activity of MSPC-5 and properties of PE;(3). New MgCl_2-Supported Single-Site Catalysts for Ethylene Polymerization In this work, a kind of new MgCl_2 support was obtained by anhydrous MgCl_2 co-milled with solid MAO, and it is a creative contribution. Then some single-site catalysts were supported on the new MgCl_2 support, and the resulted solid catalysts were tested in ethylene polymerization, the results indicated that: 1.XRD and IR analyses indicate that MAO does be coordinated with MgCl_2, which is in good agreement with the results obtained by XPS; 2.co-mlling time had no obvious effect on the texture of support after 12 hours; 3.In this work, MgCl_2 was co-milled with solid MAO for different hours, and then complex 3 was supported on these co-milled supports. It was found that co-milling time markedly influences the activity of solid catalysts, but it had negligible effect on the kinetic profile and the properties of resultant PE.

XPS研究结果表明，MAO不仅仅只和乙醇作用，MAO还与MgCl_2本身有一定的作用，这是一个极为重要的发现； 3、通过ICP和EDX表征，发现载体的脱醇温度直接影响着元素在固体催化剂中的含量及分布； 4、脱醇温度极大地影响着负载苯氧基亚胺类催化剂的活性和聚合物的性能，特别是原始载体经160℃活化4小时制备得到的固体催化剂MSPC-5的活性明显高于其他脱醇温度条件下制得的固体催化，并且催化剂寿命长，表现出稳定的动力学行为，最终获得了高堆密度(大于0.35g／ml)的球形聚乙烯颗粒； 5、本文选择MSPC-5为研究对象，考察了聚合反应参数对催化剂的活性及其聚合物的影响，研究发现：不同的烷基铝对催化剂具有非常重要的影响，特别足TIBA对MSPC-5的助催化活性最高，烷基铝的加入量有一个较佳值，聚合温度为80度时活性最高，H_2的加入使催化剂的活性明显降低且聚合物的分子量也减小；、新型氯化镁载体负载单活性中心催化剂催化乙烯聚合本文创造性采用固体MAO与无水氯化镁直接进行共研磨，制备出了一种的新型的氯化镁载体，并将该载体用于多种单活性中心催化剂的负载化研究，研究表明： 1、通过BET、XRD的表征，再次证实了MAO与MgCl_2之间具有直接作用，与XPS的研究结果相一致； 2、当研磨时间高于12小时时，延长研磨时间对载体的结构没有显著的影响； 3、将配合物3负载于共研磨时间不同的一系列载体上，乙烯聚合结果表明，尽管共研磨时间对负载催化剂的活性具有明显的影响，但是它对聚合物的性能以及催化剂的影响不明显。

Deamidation of the milk protein produced the spicy or ammonia-like flavor.Reduction and heat treatment had no obvious effect on the enzyme reaction and the flavor of the product.The order of different enzymes could influence the flavor effectively.In addition,the taste of the hydrolysate can not be improved by adding condiment.

结果表明，脱酰胺反应会使产品具有氨味和辛辣味；还原处理和加热处理，对脱脂乳粉和乳清浓缩蛋白的酶解速度和水解液风味都无明显影响；不同的酶解顺序对乳蛋白水解液的风味影响显著；用风味剂不能有效地掩盖酶解液的不良风味。

Another remarkable characteristic of printing and dye the waste water is that the colour is high, is it adopt biological carbon pool is it is it deal with to decolour to go on to it , for activated carbon absorbent spent to design originally, active charcoal adsorption method to utilize porous active charcoal material make one or many kinds of material of waste water it absorbs to be that surface get rid of in active charcoal.

印染废水的另一显著特点就是色度高，本设计采用生物碳池对其进行脱色处理，所用的吸附剂为活性碳，活性炭吸附法就是利用多孔活性炭物质使废水中的一种或者多种物质被吸附在活性炭表面而去除的。

Zoology environment aggravation basically behaves the resource that it is water rare be short of and development uses rate low; extensive cultivate course of study to make quality of agricultural zoology environment deteriorates quickly; prairie ecosystem suffers excessive depasture wait for a reason to destroy serious, natural prairie produces structural sex decline, vegetation productivity is reduced significantly.

生态环境恶化主要表现为水资源稀缺且开发利用程度低；粗放型的种植业使农业生态环境质量迅速退化；草原生态系统受过度放牧等原因破坏严重，天然草原发生结构性衰退，植被生产力显著降低。

Accordingly, a new plasmid Cm1301 was constructed containing osGP fragment (-197～-56) from the osRACD promoter with the minimal promoter,-90 region of CaMV 35S which confers Gus activity detectably only in roots. In the transgenic plants containing Cm1301, GUS activity was detected mostly in the anther.

由于35S基本启动子是一个根特异表达的启动子，因此将包含osDP5区段的osGP片段（-197～-56）与35S基本启动子连接，构成植物表达载体Cm-1301并转化烟草，研究发现，osGP区段使gus基因在雄蕊中表达水平显著提高。

The effects of temperature, dialogite-to-sulfuric acid ratio, and solid-to-liquid ratio on leaching of dialogite by sulfuric acid were researched in the leaching experiment of ores from Hubei.

通过对湖北矿的浸取试验研究，讨论了温度、矿酸比、固液比对菱锰矿硫酸浸取的影响，优化了浸取条件，并确定温度对浸取的影响最为显著，使浸取率可以达到99。

The cage effect of Gn potassium aqueous solution calculated by theα-cleavage photoreaction product distribution of substituted dibenzyl ketone was 14%, 18%, 22% and 42% for generations 1-4, respectively, which indicates that G4 takes a more close spherical shape with strong confine ability.

研究结果表明，羧基为末端基团的芳醚树枝形聚合物Gn (n = 1-4)钾盐水溶液笼效应随代数增加而增大，从G1到G4，笼效应分别为14%、18%、22%和42%，树枝形聚合物3代到4代从开放结构变为近乎球形的封闭结构的显著变化使G4表现出明显高于其他三代的笼效应。

ANSYS is a finite element simulation software used to simulate the temperature field in selective laser sintering.By using the ANSYS parameter design language,the density of the thermal flow,the velocity and the path of scanning can be controlled.The effect of the scanning path on the temperature field in the SLS process is studied. Balling,which occurs at the end of the scanning line,is caused by the dissymmetric temperature field and the great temperature gradient.

利用有限元分析软件AN SY S，对激光烧结温度场进行了数值模拟，建立了激光烧结薄板的温度模型；运用APDL语言控制热源的热流密度、移动速度以及扫描轨迹；研究了激光行程对烧结温度场的影响，扫描端点温度场的不对称及较大的温度梯度造成了端点球化现象；激光扫描线间的耦合作用使端点球化现象随扫描线的增加而逐渐显著。

What would he tell Judith and the children?

他将怎样告诉朱迪丝和孩子们呢？

I this is at that time, the opinion with peacockish true girl is full of in a heart.

这就是当时的我，一个心中布满虚荣的女孩子真实的想法。