使旋转

Acclivity 20° against to fall the silk brick, in resistance wire Yi Congcao does not drop out. The drum stove pot uses the 1Cr18Ni9Ti stainless steeliness full circle columnar order, or uses the chromium manganese nitrogen high-temperature steel casting, an origin bearing spider outside the furnace bodythe supporting, and uses the electric motor belt speed reducer to carry on the biography to use, to cause the stove pot to revolve slowly, the work piece causes it heating along with drum stove pot revolving to be even, and work piece mutually between non-cover phenomenon, after the heat treatment, theluster is consistent, stove pot another end is a feed head, by two hoop supporting.

滚筒炉罐采用1Cr18Ni9Ti不锈钢制成圆柱型，或采用铬锰氮耐热钢铸件，一端由轴承支座在炉体外支承，并采用电动机带减速机进行传用，使炉罐缓慢旋转，工件随滚筒炉罐旋转使之受热均匀，并且工件互相之间无复盖现象，热处理后色泽一致，炉罐另一端为进料口，由二只滚轮支承。

Rotating disks are the basic mechanical element of steam and gas turbines, grinding wheels, circular saws, and computer disk memories.

旋转圆盘是工业中应用广泛的一种基本机械元件，它广泛的应用于旋转机械，诸如涡轮机、圆锯、计算机硬盘等，上述系统中这些盘类结构严重的横向振动将使机器工作时的精度降低﹑动态性能下降以及造成被加工材料的浪费，严重时甚至使圆盘元件损坏。

Rotating disks are the basic mechanical element of steam and gas turbines, grinding wheels, circular saws, and computer disk memories. Large amplitude transverse vibration of rotating disks can cause failure of turbine wheels due to wheel-case contact, cutting inaccuracy for grinding wheels and circular saws, the waste in material and head-tracking errors in computer disk memories.

旋转圆盘是工业中应用广泛的一种基本机械元件，它广泛的应用于旋转机械，诸如涡轮机、圆锯、计算机硬盘等，上述系统中这些盘类结构严重的横向振动将使机器工作时的精度降低、动态性能下降以及造成被加工材料的浪费，严重时甚至使圆盘元件损坏。

The roller furnace pot uses the 1Cr18Ni9Ti stainless steeliness circled to columnar, or uses the chromium manganese nitrogen refractory steel casting, one side bearing spider outside the furnace body supporting, and uses the electric motor belt speedreducer to carry on the passing-use, to cause the furnace pot to revolve slowly, the work piece causes it heating along with drum furnace pot revolving evenly, and work piece mutually between non-cover phenomenon, after heat treatment, the luster is consistent, furnace pot another end is a feeding head,by two trolley supporting.

滚筒炉罐采用1Cr18Ni9Ti不锈钢制成圆柱型，或采用铬锰氮耐热钢铸件，一端由轴承支座在炉体外支承，并采用电动机带减速机进行传用，使炉罐缓慢旋转，工件随滚筒炉罐旋转使之受热均匀，并且工件互相之间无复盖现象，热处理后色泽一致，炉罐另一端为进料口，由二只滚轮支承。

A test model of four co-rotating disks was developed as the simplified version of a typical internal cooling system of a gas turbine compressor. The investigation was on the distribution of local heat transfer coefficient and the averaged nusselt number of the downstream main disk. Experimental analysis may lead to following conclusions: the distribution is not of monotony and multi-peaks were found along the disk surface,Nu increases with the decrease of the rotational reynold number Re(subscript w,Nu increases with the axial reynold number and the grasholf number.

针对航空发动机多级压气机盘腔的冷却问题，对具有轴向通流的三腔模型进行了系统的研究，通过对局部换热特性与平均换热特性的分析，可以表征旋转盘的热应力水平和相对冷却效果，结果表明表征旋转盘热应力水平的局部换热特性在旋转盘的半径上呈多峰分布，表征相对冷却效果的平均换热特性与旋转雷诺数Re、进气雷诺数Re以及格拉晓夫数Gr有关，当Re及Gr增加时，平均努塞尔数Nu随之增加，而Re的增加使之减小。

One is Bardina vorticity modification, and the other is Richardson number modification. Prediction results show that Bardina method has a superior capacity to Richardson number modification. Since DSM model has improved predictive results of the reversed velocity and tangential velocity, it is a potential method to predict strong swirling nonisotropic turbulent flow in stead of the longer convergence time.

本文采用了基于旋转体系使湍流脉动加强和削弱两种作用的修正方法对k-ε双方程的湍流耗散率方程进行修正，计算结果表明，从旋转体系可使湍流能量加强出发的Bardina涡量修正方法，预报回流区范围缩小，更加接近于试验值，其计算结果优于使湍流脉动削弱的Richardson修正。

The toner feeder is removably mounted in an image forming apparatus including a rotation driver for rotating a toner container and a rotation controller for controlling the rotation driver.

色剂馈送器以可移除方式安装在图像形成装置中，该图像形成装置包括：用于使色剂容器旋转的旋转驱动器和用于控制旋转驱动器的旋转控制器。

The dynamo runs at rull speed to drive main shaft,then the main shaft makes the emulsifying wings in emulsification grove rotate,which absorbs the liquid in its brand groove into ring groove through guide vanes on upper and lower side s of the groove.The v

由电动机全速运转带动主轴，经主轴转动乳化框槽内之乳化翼片，使其将桶槽内之液体经框槽上、下两侧之导流叶片吸入环状框槽内，经以主轴为中心高速圆周旋转叶片；连续使乳化翼端刀面与乳化框间极小之间系高频率之强力切割剪断、粉碎，再借叶片高速离心旋转排挤，持续循环混合，以极短之时间即可完成均质乳化之处理。

The hanging strip device includes: a hanging strip device main body; a winding section for performing the winding of the hanging strip; a winding auxiliary section, which is configured at a state that the rotation relative to the hanging strip device main body is limited and can move between the first preset position and the second preset position relative to the winding section, wherein, at the first preset position, the rotation of the winding section makes the hanging strip wrap is restricted, at a second preset position, the winding section can perform the drawing-out rotation for drawing out the hanging strip; a force applying part, which applies a press pressure to make the winding auxiliary section at the first preset position; and a convex part which allows the winding auxiliary section to be at preset point contact status relative to the hanging strip device main body when the winding auxiliary section is at the first preset position.

置在该吊带装置主体内，而且能够在第一预定位置和第二预定位置之间相对于上述卷绕部移动，其中，在上述第一预定位置，上述卷绕部的使上述吊带回绕的旋转被限制，在上述第二预定位置，上述卷绕部能够进行用于抽出吊带的抽出旋转；施力部，其施加将上述卷绕辅助部按压向上述吊带装置主体的按压力，以使该卷绕辅助部处于上述第一预定位置；和凸起部，其设置于上述卷绕辅助部或者上述吊带装置主体的任一方，在该卷绕辅助部处于上述第一预定位置时，上述凸起部使该卷绕辅助部相对于上述吊带装置主体成为预定的点接触状态

The pipelined CORDIC architecture is very suitable for FFT butterfly operation because of its high throughput and regularity, but it will consume lots of resources,this article presents an improved architecture of CORDIC pipeline,starting with the property that the FFT rotary factor is fixed but not arbitrary,and according to the mapping between the basic rotational angle of CORDIC and scale factor and the rule for transform among the scale factors.On the condition that the velocity of FFT butterfly operati...

CORDIC流水线结构因其高吞吐率及规整性，而很适合于FFT蝶形运算，但其缺点是耗资源多，本文从FFT中旋转因子固定不任意的特点出发，根据CORDIC基本旋转角度与缩放因子的对应关系和缩放因子之间的转换规律，对CORDIC流水线结构进行了改进，在蝶形运算速度不变的情况下，进一步减少所耗资源，在字长为16位的FFT中，每个旋转因子可用25位的控制序列来替代，从而使每个旋转因子的存储空间由32位减少到25位。

Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.

在对危险的南部地区访问时，他斥责什叶派民兵领导人对中央集权的挑衅行为。

In fact,I've got him on the satellite mobile right now.

实际上 我们已接通卫星可视电话了