使弯曲

In addition, we made account for the selection of inverted bending curvature of pipe axis and the length of equal curvature region, and pointed out that we can only equalize the curvature in the equal region and carrying out straightening really is in the region of unequal curvature. This is the development and perfect of bending straightening theory and this method can spread to bar straightening machine.

此外，还对反弯曲线曲率和等曲率区长度的选取作了说明，指出在等曲率弯曲区只能使曲率均匀化，而真正实现矫正是在后部的非等曲率弯曲区，这是对矫正理论的深入和完善，并且这一研究方法也可推广到棒材矫正机。

Because it can clearly reduce effective thickness of slab in bended zone under outer load.

使弯曲区的板在外荷载作用下的有效厚度明显地减小。

When train running on the track, there has interaction between whiles and track, and the track will bend because of the weight of wheel. The bend wave will propagate to box-beam and further to bridge pier. Then the vibration propagate to around soil through the bridge pier, which can cause the second vibration on buildings.

列车运行时，车轮和轨道间存在着相互作用，由于轮重的作用使轨道产生弯曲变形，弯曲波通过轨道垫块传给箱型梁，进一步传递给桥墩，然后振动通过桥墩向周围土中传播，从而进一步引发建筑物的二次振动。

For the recovery stroke, the cilium bends near the base, and the bend moves down the length of the cilium as it hugs the surface of the cell until it reaches its previous stretched out position, again having moved 180 degrees back to its original position.

之后是recovery stroke，纤毛在根部附近开始弯曲，这弯曲的动作沿着纤毛的长度移动，使其逐步靠向细胞表面，直至回复原本伸展的状态，即是同样移动了180度回到初始位置。

An inside conical surface at the lower end of the joint is designed to ensure the shaft swing freely within an angle range of 10°, thereby the axial bending stress caused by the deflection of the borehole can be eliminated effectively.

这种装置采用类似球形关节的旋转机构，消除了抽油杆柱上下往复运动产生的倒扣扭矩；在短节下端设计有10°的内圆锥表面，使转轴能够在10°范围内自由转动，从而有效地消除了由于井身弯曲而产生的轴向弯曲应力。

Using the characteristic of the regular curve boundary for a bending plate in engineering,the analytic integral formulae of assistant states in boundary element method with the linear element for a Kirchhoff circular plate are introduced and the systematic equation of BEM is established in this paper.

利用一般弯曲薄板边界为规则曲线的特点，对工程常用的圆形弯曲薄板，采用线性单元，导出K irchhoff圆板各辅助态的边界积分解析表达式，建立问题的边界元法系统方程，从而使薄板的边界元分析完全避免通常使用的高斯积分，明显提高计算精度。

Pass to count to Wisterch parameter , and the steel wire is different from the molding tool get in touch with the length, and settle the path the research taking the length work the stabber angle to get under differently pull to stir the term, mold core adoption of best severally why size, combine the best work stabber of research the Cape, and settle the path to take the length nextly steel wire is in the molding tool of have fever to measure, air inside dispel-heat calories, winding dispel-heat on the coil-canister , and its molding tool dispel-heat calories of, and cause the steel wire the temperature difference pass in and outing the molding tool to influence steel wire machine function, under the experiment inside pull to stir the term according to the same race different work stabber Cape half of adoption the Cape(7 degree,10 degree,12 degrees, the best mold Cape, experience mold Cape) settle the path to take the length(2-3 mm,3-4 mm,4-5 mms, theories length, experience length) to proceed to experiment, and get the conclusion, work stabber the Cape then is more big the steel wire get in touch with the length with

通过对Wisterch参数，钢丝与模具接触长度、定径带长度、工作锥角度的研究得到了在不同拉拨条件下模芯采用的最佳几何尺寸，并研究最佳工作锥角、定径带长度下钢丝在模具中的发热量、空气中散热量、卷筒上的散热量及其模具散热量的不同，导致钢丝进出模具的温度差别对钢丝机械性能的影响，在实验中根据同种拉拨条件下采用不同工作锥角半角、定径带长度进行试验，得出结论，工作锥角越大则钢丝与模具接触长度越短，钢丝变形越剧烈，在模具中发热量就越高，导致钢丝出模温度高，使钢丝强度、硬度升高，弯曲、扭转次数降低，并且降低模具使用寿命。在其它条件相同的情况下，定径带越长则钢丝与定径带简壁磨擦增大，使钢丝发热量加大，从而使钢丝强度、硬度略升高，弯曲扭转次数略降低但定径带的增大减小了钢丝变形产生的弹性后效使钢丝出模直径比较稳定。

When the fiber is bent,the light ejects from the fundamental mode to form whispering gallery modes produced by reflection at the cladding-coating interface,or at the coating-air interface. On the synchronous coupling condition,the light from the WG modes will couple back and interfere with the fundamental mode,which leads to bending loss oscillations.

光纤弯曲时，从基模辐射出去的一部分能量在包层涂敷层或涂敷层空气界面处发生反射形成回音壁模，当满足同向耦合条件时，WG模又重新耦合回纤芯与基模发生干涉，使光纤的弯曲损耗产生振荡。

The Solidification temperature range was defined as 110-200℃ by DSC analysis. More accelerant used can increase the casing samples dynamic performance, but more than enough accelerant can induce a severe solidified reaction that result in a smaller polymeric meshwork and reducing the sample's performance. Normally the Accelerant dosage can be 2 portions; The Epoxy resin CFRP has a obvious better performances than the Vinyl-ester Resin CFRP, i.e. had a Bend Strength of 1516MPa, LSS of 85MPa, also Tg raised to 195~C~ When used the end-carboxyl polyether to reinforce the epoxy resin, the casing sample's SS, BS and Crack Elongation all increased geminately. The CFRP performance also increased a little, that is because the performance of the CFRP mainly contributed by the CF. The reinforced resin improved the interface between the CF and resin that contribute to the little increasing.

通过DSC分析确定了该环氧树脂的固化温度范围为110~200℃，促进剂增加会提高浇注体力学性能，但过多的促进剂会使固化反应剧烈，聚合网络减小，使浇注体性能下降，一般用量为2份左右；以环氧树脂为基体的复合材料性能明显比以乙烯基酯树脂的性能提高，弯曲强度达到1516MPa，层间剪切强度达到85MPa，同时Tg也上升到195℃；用端羧基聚醚增韧环氧树脂后，其浇注体的拉伸强度、弯曲强度及断裂伸长都成倍增加，复合材料的性能也有所提高，但提高幅度不大，因为复合材料的力学性能主要由碳纤维承担，树脂增韧后改善了复合材料的界面性能。

The wood is straight in line of inkline but torrefied into wheel,the camber of which is fit for the bow compass.Even if torrefied or insolated it will never turn straight,it is resulted from the curve of torrefying .

木料笔直得合于墨线，但把它熏烤弯曲而做成车轮，它的弯曲度就与圆规画的相合，即使再烘烤暴晒，它也不再伸直了，这是熏烤弯曲使它这样的啊。

As she looked at Warrington's manly face, and dark, melancholy eyes, she had settled in her mind that he must have been the victim of an unhappy attachment.

每逢看到沃林顿那刚毅的脸，那乌黑、忧郁的眼睛，她便会相信，他一定作过不幸的爱情的受害者。

Maybe they'll disappear into a pothole.

也许他们将在壶穴里消失