使变形

As for advanced boiling water reactors, the minimum critical power ratio should not exceed 1.07; the maximum linear power density should not cause more than 1 percent of plastic deformation to fuel claddings.

对于先进型沸水堆，最小临界功率比不超过1.07；最大线功率密度不使燃料包壳产生大于1%的塑性变形。

By comparing their consumptions of materials and deflexions, a suggestion that better effect can be achieved by enhacing its girder height and lessening its webs thickness for long span continuous through girder is presented.

至于连续梁桥，由于其边跨对中间跨的弯矩可起卸载作用，中间支点截面有负弯矩，使梁内所受弯矩沿梁长分布比较均匀，因而有利于充分利用支点附近的梁截面和梁内的预应力筋；此外，由于其桥跨在桥墩上连续，致使变形曲线匀顺，因而对高速行车有利。

The soft temperature of copper matrix could be effectively improved and thermal expansion of copper matrix could be effectively restrained by the AlN particles; Under the action of porosity and thermal stresses, the thermal expansion curve of AlNp/Cu composites became non-linear with the particle volume contents increasing to a certain extent.

结果表明：AlN的加入能够提高铜基体的软化温度且对铜基体的热膨胀起到明显的约束作用；在孔隙与热应力共同作用下，AlN颗粒含量达到一定程度时，AlNp／Cu复合材料膨胀曲线随温度的上升将产生非线性变化；加热过程中热应力造成的基体塑性变形使热循环后复合材料存在残余正应变。

Based on finite element dynamic model of expansion casing with rubber sleeve, casing deformation and stress change inside casing, contact pressure at both sides of rubber sleeve and expansion parameter changes caused by friction factors during the expansion are analyzed.

根据带有橡胶筒的膨胀套管有限元力学模型，对套管膨胀过程中橡胶变形和套管内的应力变化、橡胶筒两侧的接触压力，以及摩擦因数引起的膨胀参数变化等做了分析研究；对橡胶筒的厚度、长度做了定量和定性分析，发现在橡胶与套管之间的接触摩擦因数作用下，橡胶过长将会在纵向产生&堆积&现象，在有限空间中，使其受较大的接触压力而失效。

Models employed in the analysis involving geometric large deformation, materials nonlinear and contact-friction of faying face.

组件变形和破坏模式的改变可能使连接的抗弯刚度和承载力发生较大变化。

For the TN process ladles are lined with dolomite, and for the SL process both fire clay and magnesia brick are suitable.

经钢包喷粉处理，可使钢中S.002～0.005％，P.005%，O.0015％，消除MnS型夹杂，形成不易变形的钙铝尖晶石型夹杂物。

Thus different mediums have been used between the two contact surfaces in order to investigate the variations in the normal force with the feeding level under both adhesive- and non-adhesive-contact.

利用以等色序条纹技术为核心的表面力仪，使2个分子级光滑的圆柱状云母表面在一定载荷下接触，测量其接触区尺寸和接触表面的变形情况。

Additionally, you should adjust the spacing between the "two", when the book block through fixed plate and activities-boards, rooms, with a slight resistance, milling cutter head back to work, it will not be due to the "two" spacing adjustment is too large to make the book block milling back friction cause occurs fibrillation an edge on the corresponding wear and tear of the medial two Launchpad, which is to ensure that quality milling back to prevent back milling deformation to make the package this consistent instructions.

此外，还应调整好&两板&间距，当书芯通过固定板与活动护板间时，略感有轻微阻力为度，铣背刀盘工作时，就不致于因&两板&间距调得太大，使书芯铣背发生颤动摩擦导致刀口对应的&两板&内侧磨损，这也是保证铣背质量，防止书背铣削变形，促使包本质量稳定的操作要领。

The calculation results on the fixed wheel plane gate of Deqing gate showed that t...

对德清大闸定轮平面闸门的数值计算结果表明：水头对闸门的影响总趋势是使其自振频率降低、振动模态发生变化；闸门局部开启工况第 1阶频率较低，振型主要是门叶沿竖直方向的整体振动；低阶振动模态中除门叶竖直方向的整体振动模态外，其余各阶均显示为门叶的弹性变形振动。

Based on the united calculation formulas, the corresponding computer programs and post-processors for pc computer have been developed, which can give the graph and table results of ground movement and defmation in any time.

七、根据所得到的统一计算公式，编制了相应的计算地表移动及变形的通用计算程序，移植开发了相应的后处理程序，使计算结果图形化，从而更加形象和直观。

They weren't aggressive, but I yelled and threw a rock in their direction to get them off the trail and away from me, just in case.

他们没有侵略性，但我大喊，并在他们的方向扔石头让他们过的线索，远离我，以防万一。

In slot 2 in your bag put wrapping paper, quantity does not matter in this case.

在你的书包里槽2把包装纸、数量无关紧要。