余弦

Program is divided into three parts: phase.m symbol of the baseband shaping pulse sequences, optional rectangular pulse, the square root raised cosine pulse and raised cosine pulse model.m-based procedures, completed a variety of base-band signal constellation mapping , pulse shaping and modulation command.m given spectrum shows a simple test.

程序分成三个部分：phase.m对基带码元序列进行脉冲成型，可选矩形脉冲，升余弦脉冲和平方根升余弦脉冲； model.m 为主程序，完成各种信号的基带星座图映射、脉冲成型和调制； command.m给出一个简单的频谱显示测试。

The charts of velocity vector of flow field outside the tube under five conditions with amplitude 1.3 mm and frequency 5—25 Hz were obtained,and the cosine of average synergy angle of flow field outside the tube was calculated.

实验及模拟结果表明：振动能够显著增加管外近壁区的流体速度，能够在振动方向上的管壁两侧形成有效的冲刷，随着振动频率的升高其管外近壁区的平均速度近似呈线性增加，在共振点出现峰值；相同区域内振动工况的平均场协同角余弦值要明显大于无振动工况，但不同振动频率间的场协同角余弦值变化较小。

The total of these two sorts of functions is called S-functions The indicial function, sinusoidal function, cosinusoidal function, hyperbolic sinusoidal function, hyperbolic cosinusoidal function, trigonometric function of n-order and hyperbolic function of n-order etch are all belong to S-functions.

指数函数、正弦函数、余弦函数、双曲正弦、双曲余弦、n阶三角函数和n阶双曲函数等。都是S－函数的特殊形式。文中证明了关于S－函数及其各阶导数的性质的三个定理。

A method by using 8031 single-clip microprocessor to get the syntonical bit information is presented,based on the characteristic of the modulated singal in ascending cosine envelope.

文摘：利用升余弦包络调制信号的特点，即基带信号为升余弦波，接收端可以利用这一包络，从中提取定时信息。

The propagation of elegant cosh-squared-Gaussian beams has been investigated and the analytic solutions have been obtained by means of an angular spectrum technique in uniaxially anisotropic crystals.

基于光束在单轴晶体中传输的角谱理论，对复宗量双曲余弦平方-高斯光束在单轴各向异性晶体中的传输作了研究，得到了一般的解析传输公式，并用数值的方法讨论了晶体内源于复宗量双曲余弦平方-高斯光束的两偏振分量的传输特性，结果表明，在适当参数的条件下，两偏振分量在晶体中的传输波形结构基本保持不变。

To satisfy the requirements of fast producing,low cost manufacture and large thickness preforming in the field of non-resin winding cylinder composite,the equation of retracing cosine curve was deduced based on the section principle.

为使复合材料圆柱壳体预制件适应短周期快速生产、低成本、壳体厚壁成型的要求，基于缠绕区段划分原理推导出端部余弦折回曲线方程，并结合传统纺织理论，推导了余弦折回曲线模型下端部特征参数计算公式。

Then FFT based DCT can be used to compute substrate impedance quickly. Once the DCT has been computed, it can be stored as a DCT matrix, and need not be recomputed for different substrate port configurations.

本论文把子端口之间的阻抗表示成二维离散余弦变换的形式，用基于快速富利叶变换的离散余弦变换快速地计算。

Based on the theory of cosine crossing point, the combination of three-sector approximate cosine crossing point and regulation sampling to compute trigger angle on line was given.

根据余弦交点法的原理，提出了三段近似余弦同步波和规则采样结合的一种在线计算触发延迟角的方法。

Basic characteristics of cosine transform spectrum were analyzed, where contour lines of 2D cosine transform of point mass present the shape of a quarter of concentric circles and the number of counter become small along with the increasing of wave numbers. The spectrum of vertical rectangularcylinder put up periodic zero counters which mark off quadrate areas, the values of counter in each areas alternately change between the plus and the minus, and with the increasing of wave number, the values of counter present attenuation character alike e exponent.

分析了点质量和直立矩形柱体重力异常余弦变换谱的基本特征：点质量二维余弦变换谱等值线呈1/4同心圆形状，等值线随着波数的增大而变稀；直立矩形柱体谱出现了周期性变化的零等值线，该等值线将非零等值线划分为a×b个矩形区域，而且等值线值在各矩形型区域中正负交替变化，随着波数的增大，不同的矩型域中等值线值呈e指数衰减特征。

Based on cylinder and plane dual-cosine oscillating tooth gear transmission,deduce the 3D dual-cosine oscillating tooth gear transmission,and analysis its multi-tooth mesh characteristics.

在圆柱面及平面双余弦活齿传动基础上，推演出空间双余弦活齿传动，并对其多齿啮合特性进行了分析。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。