低温碳化

After low temperature and high temperature carbonization, the compactness and stability in skin and core region are improved.

经过低温碳化和高温碳化后，纤维皮层和芯部组织的致密性和结构稳定性得到改善。

During the process,a series of artifactitious techniques are respec-tively adopted according to the types of products,such as low-temperature carbonization,crystal type control,particle surface processing,gas smash,etc.

在生产过程中，根据产品型号分别采取了低温碳化、晶型碳化、晶型控制、粒子表面处理、气体粉碎等一系列加工工艺。

Carbonitride precipitation behavior of Nb microalloyed steel during holding at high temperature and low temperature was studied through thermal simulation.

通过热模拟试验，研究了Nb微合金钢中的碳氮化析出物在高温及低温等温过程中的析出行为。

Objective To investigate the effects of perfluorochemical on in vitro long-term hypothermic heart preservation in rats.

目的 研究全氟化碳化合物在大鼠离体心脏长时程低温保存中的作用。

Through a series of quenching, tempering, tensile testing, low-temperature impact test and metallographic analysis, we ultimately came to the following conclusions:(1) low-carbon alloyed steel 20CrMn2NiMoV quenching at 870℃ and tempering at 200℃, whose structure contains tempered dislocation lath martensite and few small bainite under mixed, has the best obdurability;(2) Carbon Steel 45CrMn2NiMoV quenching at 850℃ and tempering at 620℃, whose structure is sorbitic, has a performance less than that of low-carbon Alloyed steel, but it can also meet the basic design requirements.(3) Mn can substitute for the role of Ni within limited extent.

通过一系列淬火、回火、拉伸试验、低温冲击试验以及金相分析，最终得出以下主要结论：（1）低碳合金钢20CrMn2NiMoV经870℃淬火+200℃回火，得到回火位错型板条马氏体+少量细小下贝氏体的混合组织，具有最佳的强韧性配合；（2）中碳合金钢45CrMn2NiMoV经850℃淬火+620℃回火，得到回火索氏体组织，综合性能虽然不及低碳合金钢，但也能基本满足设计要求；（3）Mn在一定程度上能够替代Ni的作用，适量的Mn和Ni相互配合可以得到最佳的低温韧性，因此&以Mn代Ni&是低温钢材料研究开发中一条可行的适合我国资源状况的合金化思路。

Non'.''- coking properties , is to be carbonized in a low temperature carbonization plant.

非'。''焦化性，巴基斯坦的煤需要在低温碳化装置中加以碳化。

They are the strengthening-toughening of 40SiMnCrNiMoA by the critical normalizing, the fine macrostructure and property matching between the all drill rod parts, the low tendency of decarburizing and delete the weak inner hole surface owe to the drill-hole and hot-rolled with core process of rolling steel.

本文研究表明，40SiMnCrNiMoA钢亚温正火强韧化特性、亚温正火使钎杆整体性能良好地匹配、较小的脱碳倾向和钻孔法消除钎杆内孔粗糙和脱碳表面是钻孔法并整体780℃亚温正火+钎柄淬火和低温回火的H22-40SiMnCrNiMoA锥体连接小钎杆延寿的主要原因。

The porous SiC was characterized by XRD, SEM, nitrogen isotherm adsorption and TPR.

制备出的多孔碳化矽通过XRD、SEM、低温氮气吸附、TPR等手段进行了表徵。

The microstructures of the new developed carbon aerogels was investigated by means of low-temperature N_2 adsorption, TEM, XRD, XPS and etc. We studied the influence of synthesis conditions on the aerogels structure, such as reactant mass percent, catalyst concentration, carbonization process and supersonic.

采用低温N_2吸附、TEM、XRD和XPS等手段研究了碳气凝胶的微观结构特点，考察了反应物质量分数、催化剂浓度、碳化过程对气凝胶孔结构的影响，同时还研究了超声作用对气凝胶微观结构的影响。

The thesis are divided into two parts. In the first part, we used 2,4,6-trichloro-1,3,5-triazine as the precursor to react with sodium which have been achieved by decomposing sodium hydrate at 623 K. At a low reaction temperature of 623 K, carbon nitride nanosphere、porous carbon nitride material and byproduct sodium chloride, would be produced.

本研究将分成两部份，第一部分是在低温下(623 K)将氢化钠粉末热裂解，生成表面积较大的熔融态金属钠，使气态的氰尿醯氯通入与熔融态金属钠在623 K反应，生成奈米氮化碳球、奈米孔洞性氮化碳材料及副产物氯化钠。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。