位置参数

If you call truncate without passing in a size, it will default to the current location in the file.

如果没有传递 size 参数，那么默认将截取到文件的当前位置。

The coming forth of virtual prototyping technology presents a new approach to study gun stability, and based on establishment of dynamic model of selections of structure parameters, the effects of stiffness and damper of elevating mechanism, stiffness and damper of trail, stiffness and damper of soil, parity of recoil mass and parity of trunnion position on firing stability are first studied with virtual prototype of gun in this paper. An improved equation of sensitivity analysis is provided, and the important degrees of factors with different dimensions can be compared.

虚拟样机技术的出现为火炮射击稳定性研究提供了新的方法，文中在建立火炮动力学模型的基础上，通过选取火炮结构参数对火炮射击稳定性进行研究，利用虚拟样机分析高低机刚度和阻尼、大架刚度和阻尼、土壤介质刚度和阻尼、后坐品质偏心和耳轴位置偏心对火炮射击稳定性的影响。

According to this,the best linear unbiased estimate method of location-scale distribution for incomplete interval censored data is presented,the confidence l.

在此基础上，针对位置-尺度分布族提出一种不完全区间数据最佳线性无偏估计方法，得到了其百分位值的置信限估计，并对工程中常见的极值分布、两参数Weibull分布、正态分布进行了详细讨论。

Some mod-el available of this kind,generally,are assumed that the microburst im-pings on the ground vertically and the turbulence is unconsidered.

该模型可模拟以任意方向倾泻的微暴流，其暴核离地高度、暴核直径、暴流强度、暴流倾泻方向、距机场位置等皆为可调参数，使用灵活方便。

The mathematical model for undercarriage load simulation system of a certain airplane is established in this paper.

建立了某型飞机起落架负载模拟系统的数学模型，将起落架位置干扰量作为系统的不确定参数，设计了系统输出力矩跟踪空气动力载荷谱的非线性控制规律并进行了系统仿真。

Analysis showed that the field injection technique of thermochemical system is feasible, the heat-generating rate and the position of "thermal spike" can be controlled and the thermochemical system is unharmful to the formation.

分析认为现场热化学体系注入工艺可行、放热反应速度与"热峰"位置可控、对地层无伤害，热化学生热提温促进稠油就地水热裂解降粘具有可行性，具体应用时应深入分析热化学就地生热提温的影响因素并优化相关操作参数。

Based on the unit quaternion decomposition of rotation matrix, this paper puts forward an algorithm to estimate motion parameters from the space position vectors of 3D feature points.

摘要本文基于旋转矩阵单位四元数分解定理，提出一种由3D特征点空间位置估计运动参数的算法。

The main contents of this paper is used in college to learn the theory of the mechanics, control theory, mechanical design and computer programming technology, and mechanical theory to simulation, including through the establishment of two parts, kinematics and dynamics of the theoretical models (including Straight leg with the knee model and the model), the use of simulation software to achieve the whole process of Walkabout sports simulation, and to study the mass center position, slope angle and other parameters of walking gait characteristics of the device, and to find the law of passive walking, in order to further less energy-consuming research to lay the foundation of the robot.

本文的主要内容就是运用在大学期间所学到的理论力学、控制理论、机械设计以及计算机编程技术，进行理论推导和力学仿真，通过建立包括运动学和动力学两部分的理论模型的（包括直腿模型和带膝关节模型），利用仿真软件实现行走器整个过程的运动仿真，并研究质心位置、斜面倾角等参数对行走器步态特征的影响，从而找出被动行走的规律，为进一步研究耗能少的机器人奠定基础。这一段翻译成英文拜托别用在线翻译那种很多都是错的

Due to this equation,he gets the variation rules of the walking beam's swing angle and the calculation formula of the distance,velocity and accelaration in the hangingpoint movement.

以CYJ10－3－37HB型抽油机为例，计算了其悬点运动参数，并给出了与简化为简谐运动和曲柄滑块机构运动的对比曲线；分析表明，悬点的上、下死点位置不是常规认为的180°和360°（或0°）曲柄转角，因而按常规计算时悬点位移将出现负值。

The obstacle (the altitude of 900 mm) process for both sides of a planetary gear train was analyzed in ADAMAS. It is proved that the physical dimension of the planetary gear train, bodywork center position and attachment coefficient are the key effect factors. The driven moment, velocity and normal pressure sharply increased as each wheel surmounting obstacles, but they were moderate after the front wheel came over the obstacles. Another weaker pulse occurred when the rear wheel began climbing, and then the parameters reached a plateau.

行星轮系的结构尺寸、车体质心位置及附着系数对越障高度影响较大；各轮系越障时出现驱动力矩、速度和正压力急增的现象，前轮系的前轮越上障碍后，各参数值趋于平稳，后轮越障时又出现瞬时脉动，但脉动较小，后轮系也有相同的变化趋势，各轮的阻力矩和输出功率与正压力变化趋势相同。

And Pharaoh spoke to Joseph, saying, Your father and your brothers have come to you.

47：5 法老对约瑟说，你父亲和你弟兄们到你这里来了。

Additionally, the approximate flattening of surface strip using lines linking midpoints on perpendicular lines between geodesic curves and the unconditional extreme value method are discussed.

提出了用测地线方程、曲面上两点间短程线来计算膜结构曲面测地线的方法，同时，采用测地线间垂线的中点连线和用无约束极值法进行空间条状曲面近似展开的分析。