位置上

The Complex Frequency Image Method which estimates the positions of poles by the positions of maximums of the negative second order derivative in complex plane is presented, and on its basis the Complex Frequency Trap Method is given.

提出了由复平面上负二阶导数的极大值的位置来估计极点位置的复频图象法，并在它的基础上给出了复频陷波法。

The method is :there are two perpendicular axes whose distance are controlled ,one is the axis of work table, the other is fixed with a microscope for aiming.

该测量方法是：两个相互垂直且间距可调的数控回转轴，一轴与工件的回转中心重合，另一轴上固定可移动的瞄准显微镜，当显微镜瞄准被测孔时，两轴的转角由各自的圆光栅测出，两轴之间的角度位置确定曲面壳体零件上小孔的孔位置，同时采用CCD摄像头，利用图象处理技术实现小孔的尺寸测量。

We label the ultra-high frequency RFID tags on books to test the RFID readability. We consider the following factors: the distance, the angle between RFID reader and books, the thickness of books, the tag position on the book, and read many books simultaneously, etc.

我们用超高频的标签贴在书本上，实际测试RFID应用在书本上的读取率，并探讨距离、角度、书本厚度、标签贴在书本位置、多本书的影响以及多本书不同位置的读取率等因素。

The main characteristics include: the quiet Sun corona has a rapid response to the flare heating, within 2 second the corona temperature increases nearly one order of magnitude, but later such increase becomes very slowly; the downward velocity at early stage of impulsive phase is too small to be negnected; chromospheric evaporation made by conduction shows some intensely, the maximum evaporated velocity may be as large as 1000 km/s; the chromospheric condensation appears just when the chromospheric evaporation takes place and its place always coincide with that of transition region in the early stage; the maximum of chromospheric condensation occurs also in the early stage of impulsive phase, at which the density in condensation may be larger two order of magnitude than that of surround and the downward velocity may be as large as 100 km/s; after the maximum of chromospheric condensation, its strongth decreases gradually but its width becomes greater with time and have a tendency to transport into deep chromosphere; the front of chromospheric condensation heats atmosphere obviously and the temperature in the chromospheric condensation is higher than the original case; the downware velocity of transition region may be greater than 100 km/s at the early stage; when the evaporated material collide at the top of loop, the densityand the presure there increase rapidly, which result in the formation of a shock wave; and so on.

在改善色球辐射损失和精确分辨过渡区的基础上，通过联立求解连续性方程、动量方程和能量方程，构造了一维磁限制性耀斑环在热沉积作用下的大气动力学模型，获得了耀斑热模型下脉冲相早期较为细致的大气演化理论图象，其主要特征是：耀斑对宁静日冕的加热相当迅速，仅2秒钟日冕温度增加即达一个量级，之后日冕温度增加缓慢；脉冲相早期日冕向下速度很小，几乎可以忽略，热传导驱动色球蒸发，其过程较为激烈，蒸发极大速度可达到1000km/s；色球压缩区与色球蒸发几乎同时形成，且在早期其位置总是与过渡区位置重合；色球压缩极大发生在脉冲相早期，其时密度可高于周围约2个量级，向下速度可超过100km/s；色球压缩极大后，其强度逐渐减弱，但宽度明显增大，且渐渐脱离过渡区往色球传播；压缩区内物质温度要高于原先的大气温度；过渡区下降在脉冲相早期相当迅速，可超过100km/s；当蒸发物质在环顶高速相碰时，环顶的密度、压力迅速增大，且温度也有所增加，导致形成激波，其波面以每秒上百公里的速度自环顶向下传播；在脉冲相前期，日冕软x辐射对色球的加热作用可以忽略；等。

Calculates the coordinates of the spindle and drive shaft and checking the center distance, determined department spindle must use dislodges the gear.

根据柴油机齿轮室盖的结构特点、加工部位、尺寸精度、表面粗糙度及生产率等要求，确定该机床为单工位卧式组合机床；为确保加工精度，采用&一面两销&的定位方案；为实现无级调速，安全可靠，选择液压滑台；根据零件的大小及被加工孔的位置确定主轴箱的轮廓尺寸；由加工工艺选择滚珠轴承主轴，通过计算扭矩确定主轴和传动轴的直径；齿轮的模数是通过类比法确定；齿轮齿数和中间传动轴的位置是由&计算、作图和多次试凑&相结合的办法确定；计算主轴、传动轴的坐标并进行中心距验算，确定部分轴上需采用变位齿轮；轴上的齿轮套、键等零件按轴号选取相应的标准件。

Everyone jockeyed for the best position, climbing seats and stepping on railings in an effort to gain themost favorable vantage point.

所有的人都在希望找一个最佳位置，有的人站在座椅上，有的踩在栏杆上，努力占据最有利的位置。

However, if the trigonal control point and datum transformation model do not exist, the result of base station single point absolute location can be used as reference coordinate, the measured result of which can be geo_referenced to remote sensing image using some tiepoints on the basis of the first result above.

例如 ，在利用遥感影像分类时，需要在外业获取用于监督分类的训练样地或是分类结果精度检验样地的大地坐标信息；在进行稀有树种区域分布特征调查时，希望能在遥感影像上标识出每个树的具体位置；发现某河段发生污染时，很可能需要将它的精确位置以线或面的形式显示在其它矢量或栅格图层上。

In terms of defects of the traditional oblique wedge die with several side holes that had position degree at the same product,method of integration with rotating wheel and slant was adopted.

针对传统的斜楔模在同一制件上冲制有位置度要求的几个侧孔时的缺点，采用转动盘与斜面相结合的方式，在同一副模具上同时冲出有位置度要求的4个孔。

First, second and third position sensor controllers control the focus servo to focus the He--Ne laser beam on the glass substrate in response to the pit width of the glass substrate by sensing the laser beam for focusing reflectedupon the glass substrate.

此聚焦系统利用第一、第二、第三光点位置敏感器去控制氦一氖雷射，使其能够在玻璃基板上产生正确的凹坑宽度，而第一、第二、第三光点位置敏感器即藉著聚焦在玻璃基板上反射而回的氦一氖雷射作为聚焦控制。

Next, connect a waist prusik and a foot prusik (used to extract yourself or a partner from a crevasse) onto the rope using a prusik hitch and clip these with a separate locking biner to your harness.

接着，在结组绳上打上&胸式&、&脚式&两个普鲁士结（译者注：指长度到胸部位置和到脚部位置）（用于在冰裂缝中自救或救出同伴），把它们扣入安全带上的另一个独立主锁。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。