位置

A dance position where the leader's left side and the follower's right side are in contact or almost in contact, and the opposite sides of their bodies are open in a V-Shaped position, leader looking right and follower looking left.

男士的左侧与女士的右侧接触或几乎接触，两人身体另一侧打开呈V字形位置，引导者在右，跟随者在左，是PP的反向位置。

A dance position where leader and follower are side-by-side facing the same direction with leader's right arm wrapped around follower's waist holding follower's left hand and leader's left hand and follower's right hand are connected in front of the bodies at about waist level.

Cuddle Position 拥抱位置：舞伴两人并肩面向面相向，引导者右臂环过被引导者的腰部握住被引导者的左手，引导者左手与被引导者的右手在两人身体前方约腰部高度相握，也可以左右位置相反过来做。

However, if the trigonal control point and datum transformation model do not exist, the result of base station single point absolute location can be used as reference coordinate, the measured result of which can be geo_referenced to remote sensing image using some tiepoints on the basis of the first result above.

例如 ，在利用遥感影像分类时，需要在外业获取用于监督分类的训练样地或是分类结果精度检验样地的大地坐标信息；在进行稀有树种区域分布特征调查时，希望能在遥感影像上标识出每个树的具体位置；发现某河段发生污染时，很可能需要将它的精确位置以线或面的形式显示在其它矢量或栅格图层上。

Two dimensional computer models of the average man, small man, and large man were developed to represent the geometry and movements of operator in seated postures on the basis of analyzing the earth moving machinery's characteristics. The human H point was taken as datum point and the posture angles were linked to easy operation, open vision and comfortable seat. The H point region was obtained by means of CAD technique. The region can be used for design and/or check purposes.

用计算机辅助设计技术，开发了求解工程机械驾驶员适宜驾驶位置的H点分布系统，分别绘制出了中等身材、小身材和大身材驾驶员适宜驾驶位置时H点区域图，该区域为驾驶员座椅和司机室内相关设施的合理布置提供了理论根据。

The height of swing arm is regulated by the handwheel at the top of the machine and the cutting stroke is regulated by the timer so as to easily obtain optimal cutting position to improve work efficiency and prolong the service life of die cutter and padding plate .

摆臂的位置高低由机器上端的手轮调节，冲裁行程由时间计时器调整，这样可以轻易获得最佳裁切位置，提高了工作效率，延长了刀模和垫板的使用寿命。

Based on finite element analysis of the die spotting machine frame,the real case of stress distribution and deformation is simulated,by which the biggest deformation and stress location are identified.

通过对合模机机架进行有限元分析，模拟了真实情况下机架的应力分布和位移变形情况，得到了位置变形最大和应力值最大的位置。

In terms of defects of the traditional oblique wedge die with several side holes that had position degree at the same product,method of integration with rotating wheel and slant was adopted.

针对传统的斜楔模在同一制件上冲制有位置度要求的几个侧孔时的缺点，采用转动盘与斜面相结合的方式，在同一副模具上同时冲出有位置度要求的4个孔。

First, calculates the fast moving average (usually 12 days) and slow moving average (usually 26 days) by exponential calculation method; second, make fast line value minus slow line value to gain the difference of relative distance. In order to make the trend signals more clear and less influence exerted by of excessive price fluctuation, the difference should be smoothly calculated (general elect 9 days) to get average of difference value. Chart the difference and its average in a coordinate with time for horizontal axis and MACD for vertical axis. Then we can apply the identical, contrary or cross signals through observing their direction, relative and absolute positions.

它首先以指数平滑计算法计算出快速移动平均线（一般选12日）慢速移动平均线（一般选26日），再以快速线数值减慢速线数值即得到快慢线相对距离的差离值，为使趋势信号更明显并且不受股价过分波动的影响，对差离值也进行平滑计算（一般选9日），得到差离值的平均值，把差离值和差离平均值画在以时间为横轴，以MACD为纵轴的坐标上，通过观察差离值和差离平均值的方向、绝对位置和相对位置关系，把它们的同向、异向和交叉现象作为买卖信号的提示。

The influence of PDIC position error on the DPD signal is analyzed and computed using the DVD-ROM parameters based on the optic disk scalar diffraction model.

在光盘标量衍射模型的基础上，引入光电探测器的位置误差参数，根据DVD-ROM的盘片参数，计算并分析了位置误差对差动相位探测信号的影响。

The results indicate that the interface curve in width varies along the flow direction. The flow rate ratio controls the coextrusion interface location. The interface deviate value increases with the increasing of the flow rate ratio. The difference viscosity of two layers polymer leads to the interface deflecting towards the lower viscosity side.

结果表明：宽度方向共挤出界面的形状和位置沿聚合物流动的方向不断变化；界面偏移量的大小随着流量差异的增加而增大；聚合物入口流量的变化是导致共挤出界面位置变化的决定性因素，流量比的变化对出口处界面形状的影响不大；两种聚合物粘度的不同会导致界面偏向粘度较低的熔体一侧。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。