传热

Experiments are carried out for two types unusual eddying tube fuel perheater,and the results show the total heat transfer coefficient is 1.2～1.262 times and friction factor is 2.8～9.0 percent higher than that of smooth tubes with the same size.

对研制的两种不同结构形式的异形凹槽旋流管式燃油预热器进行了试验研究，结果表明研制的燃油预热器总传热系数要比相同尺寸光滑管式预热器提高20％～26.2％，而油侧压降仅增大2.8％～9.0％。

Based on detailed analysis of heat transfer of electric arc and scrap melting process, an integrated model was estab-lished.

在详细地分析了电弧传热和废钢熔化过程的基础上，建立了完整的废钢熔化过程数学模型。

Based on the experiment data of local temperature and heat transfer coefficient, some empiric formulas for the heat transfer and resistance coefficient are given.

并基于肋化表面的温度和放热系数分布测定值，得出了可供实用的肋化传热以及阻力计算公式。

A mathematical model of heat transfer in batch type radiant-tube enameling furnace is established by imagine plane method and the calculation is made.

利用假想平面法建立了室式辐射管搪烧炉传热数学模型，并进行了仿真计算，结果表明，假想平面法能够大大简化室式辐射管搪烧炉内大量的角系数的计算，并可对炉子的有关参数(如辐射管的距径比、布置、炉墙结构等)进行优化计算。

The result of study shows that the exergy efficiency of the combined cycle can reach 51.12% because of utilizing the high-temperature endotherm of gas side and the low temperature exotherm...

结果表明，燃气蒸汽联合循环系统利用了燃气侧高温吸热和蒸汽侧低温放热的特点，使得其效率高达51.12%，比常规的纯蒸汽动力循环的效率(最高约40%)高得多；燃料化学能转化为热能及传热引起的损失所占比例最大，为31.67%。

However, MSR is a strongly endothermal reaction, which is usually limited by heat and mass transfer and shows a lower dynamic responds and lower utilization ratio of catalyst in the catalyst bed. Therefore scientists begin to study micro-channel reactors which have better transport characteristic of heat and mass.

甲烷蒸汽重整反应是强吸热过程，该反应在固定床反应器中因受热质传输的限制，存在动态响应慢、催化剂利用率低等问题，人们转而研究具有良好传热传质性能的微通道反应器。

With the help of finding the effects of the heat transfer process of building envelope on the indoor environment, solving the indoor flow field and temperature field, the heat convection coefficient of wall surface is obtained at last.

通过发掘建筑维护结构的传热过程对室内环境的作用与影响，求解室内速度场、温度场，从而得到墙体表面对流换热系数。

Heat Conduction ; Density of heat transmission ; Fourier Equation ; Coefficient of heat conduction

由于热的良导体传热性能较好，稳态时内部温差小，通常是加大样品的长度，使两端的温差足够大，便于测量。

In order to investigate the frictional temperature of brake rotor,the thermal transmission model of brake disc during braking was theoretically derived,and the equation of heat conduction on the basis of change of friction heat flow intensity and experimental research to real brake plate was obtained.

为了研究摩擦过程中制动盘摩擦表面温升的情况，在1∶1惯性制动实验研究的基础上，基于制动过程中摩擦热流强度的变化，建立了制动时制动盘传热模型，推导出了制动盘摩擦表面温度的计算公式，并用此公式算出的结果与实测温度进行了对比。

Based on the thermodynamic analysis of heat transfer process between water jet and the blade surface, the differential equations of heat convection and differential equation of steady heat conduction between water jet and the blade surface are established. Power expression of heat exchange and temperature field expression of the blade are derived.

根据对水射流与刀片间传热过程的热力学分析分别建立了水射流与刀片表面对流换热微分方程组和热源与刀片间的稳态导热微分方程，推导出水射流对刀片的换热功率表达式和刀片内温度场表达式。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐