传动齿轮

In the second test, the frequency response function is measured and the primary natural frequency has been obtained.

前者研究了不同转速下行星齿轮动态响应的频谱特性，后者则给出了行星齿轮传动的固有频率。

That the curves of the normal force and friction force between two corresponding gear teeth in a given condition can supervise the design and optimization of gear system.

得到了某一特定传动条件下单对齿轮轮齿法向力及齿间摩擦力的变化规律曲线，从而可以指导齿轮系统的设计和优化。

It is very extensive that the interior gear wheel is used in industry.

内齿轮在工业中应用十分广泛，对内啮合齿轮传动的特点进行了分析。

Based on the theory of gearing and differential geometry, a series of geometric relationships between conjugate tooth surfaces are analyzed, basic relationships of normal curvature as well as geodesic torsion between conjugate tooth surfaces are derived mathematically for the most general form of gearing.

基于微分几何和齿轮啮合理论，分析了共轭啮合齿面间的一系列几何关系，从而揭示了两个作空间共轭啮合运动的齿面之间的法曲率、短程挠率的内在几何联系。作为上述理论的具体应用，研究了准双曲面齿轮传动两齿面之间在给定参考点处的法曲率、短程挠率的关系

The discriminant is derived using the above theory wether gear profile need to modify and the formula using to calculate precisely modify measment of gear is derived. An elastic curve of the harmonic drive that the profile of the rigid gear and elastic gear are involute is studied.

利用本文建立的弹性啮合理论推导出齿轮齿面是否需要修形的判别式和修形量精确计算的公式；利用本文弹性啮合理论研究了谐波齿轮传动中的弹性曲线求解问题。

According to the principle of gear modification, this paper presented a new method, which determines the modification of spur gear using the dynamic system identification and optimum control theory.

摘 要：提出了一种利用动态系统辨识与最优控制理论相结合确定齿轮修形量的方法：在实际工况下，通过实验采集直齿轮传动系统实际动态信号进行系统辨识，然后求取系统的最优控制，将其转换为振动最小的修形量。

For the process of forming member gear, the machine setting parameters for Free-form generators can be determined by either direct or equivalent transformation, both methods coincide with each other. For generated pinion, the author utilizes a imaginary modified member gear to get original machine setting parameters for traditional cradle-type generator, and then establishes a mathematical model including the second and third order contact parameters of the gear pair for optimal synthesis to optimize the quality of contact transmission of the gearing.

对于成形法加工大轮可以直接或通过等效转化的办法确定Free-form型机床的调整参数，二者是完全一致的；对于展成法加工小轮，作者利用假想修正大轮的概念获得传统摇台类机床调整参数的初值，然后建立包含齿轮副二阶接触参数和三阶接触参数的优化数学模型，以优化齿轮副的啮合传动质量。

Taizhou Qionghua Gearing Machines General Factory, one of the closest branches of Hongtai group, has many famous products, for Qionghua brand cyclical pin-wheel decelerator, cycloidal pin-wheel electric roller, cylindrical gearing decelerator, Rigidly face decelerator and worm wheel decelerator, etc.

泰州市琼花传动机械总厂系集团股份成员企业，主产品有"琼花"牌摆线针轮减速机、摆线电动滚筒、圆柱齿轮减速机、硬齿面减速机、平面二次包络减速机，行星齿轮减速机，风力发电增速机，蜗轮蜗杆减速机等系列优质产品。

By the solution method of the principal curvature and Boussinesq problems, the equations of the contact characteristics of the contact points on the face gear are developed.

利用曲面上任意点处主曲率的计算方法，得到了传动中圆柱齿轮和面齿轮上接触点处主曲率的变化规律。

The radial power of each of inner gear of transmission ring which works on output shaft is zero.

每一组传动环板的内齿轮对外齿轮的径向作用力的合力为0。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。