传动

The collector ring has low distortion and high repeatability, and also can be easily used in measuring system for any rotational system.

首次开发研制了适用于高速齿轮传动动态性能测试需要的非接触式红外线集流环。

Since the rocking of the nipper shaft causes the nippers to move backward and forward through a series of links, the original position of nipper frame is altered when changing the detaching distance, resulting in the change of other process parameters of the comber.

由于精梳机的钳板摆轴传动钳板的方式都为四连杆机构，在进行落棉隔距的调整时，改变了连杆的初始位置，因此精梳机的其它工艺参数也随之改变。

To make the engineering machine economize on energy efficiently will spread to move system to carry on a control towards launching machine and, reasonable allotment power, make it be placed in the best work condition;For easing a pilot to labor strength and improvement to manipulate function, need to adopt an automatic control, carry out an engineering machine automation;To complete the homework of high technical ability need intelligence to turn;For the sake of exaltation safety, demand safety control, carry on circulating appearance surveillance, the breakdown reports to the police automatically;Because the construction realm expands, in order not to the personnel arrive can't and not come-at-able place and the very bad place of the homework environment go to homework, need to be adopted long-distance leave remote control and no man to drive a technique.

要使工程机械高效节能，就要对发动机和传动系统进行控制，合理分配功率，使其处于最佳工况；为了减轻驾驶员劳动强度和改善操纵性能，需要采用自动控制，实现工程机械自动化；要完成高技能的作业，就需要智能化；为了提高安全性，需要安全控制，进行运行状态监视，故障自动报警；随着建设领域的扩展，为了避免人员到达无法及不易接近的场所及作业环境十分恶劣的地方去作业，需要采用远距离遥控和无人驾驶技术。

Because high temperature of drill fluid ,high pressure and complicate operational mode ,adopting common seal cant achieve reliable seal.

由于涡轮钻具减速器入口的泥浆温度高、压力高，而且钻进过程中工况复杂多变，要采用一般的密封装置实现不了这种可靠的密封，更不能达到减速器高效率传动、长寿命使用的目标。

In this paper, hydraulic impact that caused by the hydrodriving vibration compactor in the course of the starting vibration and the measures of reducing the hydraulic impact were studied.

本文对液压传动振动压路机起振过程的液压冲击机理及其防治措施进行了研究。

The integral force of RV drive is a redundant system. In order to fit in with the need of engineering practice, a rational deformation compatibility condition to solve redundant system problem in a way of static determination is presented.

RV传动系统整体受力是静不定系统，为适应工程实际需要，本文提出合理的变形协调条件，使静不定系统问题能用静定的方法求解。

The high-voltage high-power multilevel converter and AC motors drive techniques are summarized compendiously for domestic and overseas studies in the prolegomenon of this dissertation. The evolution and research status of multilevel converter topologies are analyzed, the development of AC variable speed techniques and the characteristic of DTC are discussed, also, the aim and significance for the research are demonstrated. In this dissertation, SVPWM pattern and implement method have been addressed comprehensively for three-level NPC inverter.

本文绪论部分针对国内外高压大容量多电平变换技术和交流传动控制技术作了简要综述，着重分析了多电平拓扑结构的发展和研究现状，讨论了交流调速的发展和直接转矩控制技术的特点，指出本文选题的目的和意义。

In addition, depending on the method of numerical simulation and theoretical analyses, some kinematic and geometric features of 0° involute—enveloping worm gear drive, such as meshing surface, first—type limit, second —type limit, worm surface, the numerical representation of contact line and bearing contact, are systematically studied. These relevant conclusions provide an important basis for the design and manufacture of new type worm gear set. As we predict, the method of numerical simulation has special effect in solving the question of complex conjugate surface.

综合利用仿真方法与解析手段，对0°渐开线包络蜗杆传动的啮合面、一类界限、蜗杆齿面构成、仿真接触线及仿真接触域等运动几何学特性进行了系统研究，有关结论为此种新型蜗杆副的设计与加工提供了重要基础，并且显示出数字仿真方法在研究复杂共轭曲面问题时所具有的特殊功效。

It is determined that the pitch cone of honing wheel depends on the number of teeth in the honing wheel and the angle between the common normal of pitch cones and the plane parallel to both gear and honing wheel axes.

论文摘要：分析了基于交错轴传动的珩齿原理，导出珩磨轮与被珩齿轮在啮合点处的相对滑动速度的数学模型，根据该数学模型可以判定，珩磨轮的节锥面由珩磨轮齿数以及公法线和与珩磨轮及被珩磨齿轮的轴线平行的平面的夹角两个参数所确定。

Analyzing the honing principle of spiral bevel gears based on crossing-axis transmission, the mathematical model of the relative sliding speed of the contact point between honing wheel and gear is achieved. It is determined that the pitch cone of honing wheel depends on the number of teeth in the honing wheel and the angle between the common normal of pitch cones and the plane parallel to both gear and honing wheel axes.

分析了基于交错轴传动的珩齿原理，导出珩磨轮与被珩齿轮在啮合点处的相对滑动速度的数学模型，根据该数学模型可以判定珩磨轮的节锥面是由珩磨轮齿数、公法线和与珩磨轮轴线平行的平面夹角所确定。

The objective is to subjugate and discourage the people, because that allows the elite to continue to rule unopposed.

其目的是压制和打击人民的积极性，因为这可以让实权派继续统治不会沦为反对派。

GOD,this is the second time you vanquished me!

天啊，这是第二次你打败了我！