从轴

The stress calculation method and strength condition of PET aerated water bottle were obtained from theory. The strength of PET aerated water bottle was simulated and calculated ANSYS. The stress graphics of the bottle with different thickness was plotted and their stress property was analyzed. The influence of axial load and grooves on bottle stress was also studied.

从理论上得到了聚酯碳酸饮料包装瓶的应力计算方法和强度条件；利用ANSYS对其强度进行了有限元模拟和计算，得到了不同厚度的聚酯碳酸饮料包装瓶的应力图，并分析了其应力特点；同时研究了轴向载荷和瓶体开凹槽对瓶体应力的影响。

The stress calculation method and strength condition of PET aerated water bottle were obtained from theory. The strength of PFT aerated water bottle was simulated and calculated ANSYS. The stress graphics of the bottle with different thickness was plotted and their stress property was analyzed. The influence of axial load and grooves on bottle stress was also studied.

从理论上得到了聚酯碳酸饮料包装瓶的应力计算方法和强度条件；利用ANSYS对其强度进行了有限元模拟和计算，得到了不同厚度的聚酯碳酸饮料包装瓶的应力图，并分析了其应力特点；同时研究了轴向载荷和瓶，婚开凹槽对瓶体应力的影响。

Downstream axially from nose apex to afterbody,a local sectional-side-force extremum always presents itself behind the forming of the corresponding shed vortex and new lee-side vortex.

沿轴向从头部尖顶往后体，截面侧向力局部极值的形成总是滞后于相应脱落涡、新生背涡的形成，截面侧向力局部极值的大小同时取决于相应脱落涡、新生背涡的形成方式和相应背涡的强度。

AMM Shafts can be made from brass, aluminum, carbon steel and stainless steel and are finished with heat treatment.

东盟轴可以从黄铜，铝，碳钢，不锈钢和完成热处理。

It gives the main circuit and the project of the control,and explains the c...

给出了整个系统的主电路与控制方案，从理论上解释了这种新的轴带发电机系统的正确性和可行性。

Low pulse before sift network operating principles : the use of double - sieve drum aircraft design; Work, pulp before sift upper tangent pressure from the network into; Pulp from the filter into the upper body of the middle two filter drum, double tilt-rotor rotary rotors, while the centrifugal force and centripetal forces role, through good mix inside and outside pool in sieve sieve drum body low extremity good mix of outflow; pulse in the tilt-rotor rotary drum filter

低脉冲网前筛工作原理：该机采用双筛鼓设计；工作时，浆料从网前筛上部切线压力送入；浆料从筛体上部流入到两个筛鼓中间，在双旋翼转子旋转时产生的离心力和向心力的同时作用下，良浆通过内、外筛鼓汇集于筛体下端的良浆管流出；脉冲旋翼在旋转时筛鼓不会赌赛，浆渣受转子旋转产生的轴向推动力，向下流送的同时被浓缩并逐步移到排渣口。

Qualified plastic film in gravure printing wheel system transformation cards and membership cards should be controlled in making the two-part tensility, that is, from feed axis to feeding traction roll and roll traction from your material to your material after the participation of various ministries.

等边的塑料薄膜在瘪印轮转制卡和会员卡制息洋不主给答把持两个局部的压辛，即从给料轴到给料牵引辊和从播料牵引辊到播料后各部。

Flange joint bolt is just put in from the side of flange joint component, nut screw in from the side of flange of coupling.

法兰连接螺栓只能从被连接构件的法兰侧放入，螺母从联轴器的法兰侧拧入。

This process improves the appearance of a worsted fabric by removing fibrous material from the surface.a two-cylinder cutting machine is 英语翻译 in plate 51,whilst the principle of the action of the cutting parts is 英语翻译 in fig.43.the essential features arethe cutting—mower,together withthe ledger—blade,both andbeing positioned in a 商务英语报告格式,andthe bed over over which the cloth passes.there are also drawing rollers to pull the piece through the machine,a setting—up roller and several guides and tension meshanisms.the flocks shorn from the cloth are removed by a suction device.

这个过程通过从表面消除纤维状物质从而提高了精纺面料外观。每个两缸切割机总在51号板显现，虽然原则上该作用是在于43号切削部分。其重要特征是（1）切割部分，和（2）固定刀片，（1）及（2）两部分都被翻译在车头，以及（3）当织物通过时延伸到织物车床上。在滚轴作用下织物通过罗拉并被拉紧，成片毛屑从织物上被抽吸装置抽走。

2 C节,原文为: The coupons shall be removed so that the specimens shall have their longitudinal axes at a distance below the nearest heat treated surface equivalent at least to the greatest distance that the indicated high tensile stress surface will be from the nearest surface during heat treatment and with the mid-length of the specimen at a minimum of twice this distance from the second heat treated surface.

建议译为：试件的切取应使试样的纵轴在最近的热处理表面以下，其距离至少等于从表明的高拉伸应力面到热处理时最近表面的最大距离，且试样的一半长度应位于离第二热处理表面这一距离（指从表明的高拉伸应力面到热处理时最近第二表面的最大距离—译注的至少二倍。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐