交比

According to that characteristic and based on the differential equation of the deformed surface of the orthotropic plate, with one principal direction size fixed, changing another principal direction size linearly, maintaining elasticity coefficient the same as in the first principal direction and Poisson ratio equal to the geometric mean of two principal Poisson ratios, the original orthogonal plate is equivalent to an isotropic plate. Results obtained show that the deflections of the equivalent isotropic plate are the same as the deflections of the original orthotropic plate at the corresponding points, the forces of the correspondent points have simple relations.

根据这一特性、从正交各向异性板挠曲面的偏微分方程出发，保持一个主方向尺寸不变，另一主方向的尺寸做线性缩放，保持弹性模量与第一主方向相同，泊松比取2个主方向泊松比的几何平均值，将这类正交各向异性板等效为一块各向同性板；通过分析得到：各向同性板任意点的挠度就是原正交各向异性板对应点的挠度，各对应点内力之间存在简单的比例关系，该文的方法将为工程技术人员提供方便，同时可以更加直观的认识正交各向异性板的受力。

The thesis also draw several conclusions as follows:(1) Orthogonal experiment design method can be viewed as a special case of genetic algorithm, i. e. a genetic algorithm with a fixed initial population, an oriented-mutation operator and one evolution epoch.(2) In terms of running steps, genetic algorithm is more complex than orthogonal experiment design method.

论文首次对正交试验设计法和遗传算法这两种独立发展起来的方法进行比较研究，提出(1)正交试验设计法是遗传算法的一种特例，即是一种初始种群固定的、只使用定向变异算子的、只进化一代的遗传算法；(2)遗传算法产生的优化解优于正交试验设计法产生的优化解，且遗传算法处理交互作用项的效率高于正交试验设计法；(3)遗传算法的步骤比正交试验设计法复杂，所需的试验次数也要多。

The results show that the microscopical pore structure of the three dimensional orthogonal woven carbon fabric structure perform is composed of body-centered cubes which arranged periodically at spaces. The net structure and shape of the pores of perform are determined by the size and proration of the fasciculus diameter, which are key factors influencing the gaseous permeability and final density of composites. Once the proration of the fasciculus diameters of different directions is determined, the trend of diversification of the permeability followed by pore rate during CVI process and the density of composites are stated, and the permeability increases with the increase of the fasciculus diameter.

研究结果表明：三维正交结构炭纤维预制体的宏观孔隙结构在空间上可以看成是由呈周期性排列的体心立方"晶胞"构成； X ， Y 和 Z 3个方向纤维束直径大小及比例关系决定三维正交结构炭纤维预制体宏观孔隙网络的结构和形状，也是决定反应气体在孔隙中的比渗透率和复合材料最终致密度的重要因素；当 X ， Y 和 Z 3个方向纤维束直径的比例关系一定时，不同预制体在CVI增密过程中比渗透率随孔隙率变化的趋势相同；复合材料的最终致密度一定；比渗透率随纤维束直径增大而略有增大。

The conversion boundary of self-incompatibility was researched by sowing by stage. Sunshine of day and temperature was studied critically by investigating leafage and researching traits indoors. The results showed that the daily minimum temperature was the principal factor of affinity conversion and the affinity conversion boundary was 16.5~18.1℃.HE97 was primarily regard as self-incompatible line in this research. The method was by inbreeding and sib HE97, Half the silk of HE97 and Zheng58. Inbreeding and cross have been done simultaneously. The extending condition of pollen tube was observed by dying the silk after pollinating 4 hours. The individuals with pollen tube were observed having seeds, while the individuals without pollen tube were observed having few seeds or no seeds. So this study regard HE97 as sporophytic self-incompatibility .The planting ration of female parent HE97 and male parent 87-1 was 4:1.The nature cross-pollination was studied by the theory of endosperm xenity, the study show that the setting percentage of HE97 was 625%, in which the seed in self was 70% and the seed in hybrid was 30%. This was consistent with the study of silk anatomy structure, then come to the same conclusion: compatible pollen germination and fertilization can stimulate the self-incompatible pollen germination and fertilization in the same corn cob.

通过分期播种，进行了光温敏自交不亲和材料HE97亲和性转换区间的研究，依据田间跟踪调查叶龄及室内考种研究了HE97亲和性转换区间的光温临界值，结果表明：1日最低温度是影响HE97自交不亲和性的主要原因，亲和性转换区间在16.5℃～18.1℃之间。2通过HE97自交和姊妹交以及将HE97与郑58作为双亲，各自的花丝一分为二，分别正反交，授粉后4个小时分别取其花丝进行固定、染色，观察花粉管的伸长情况，根据结实率与花粉管伸长的对应关系，结果发现观察到花粉管的对应植株收获到了种子，而没有观察到花粉管的对应植株结实率极低或没有结实，本研究把HE97初步划为孢子体自交不亲和类型。3以HE97为母本，87-1为父本，按4母：1父行比，通过花粉直感效应研究天然异交率，结果母本HE97结实良好(62%)，其中自交粒占70%，异交粒占30%，结合花丝切片观察表明，亲和花粉的萌发及受精会导致落在同一果穗柱头上不亲和花粉的萌发不再受抑制。

And presents some commonly process and attentions in applying the FEM software ANSYS to PCM analysis.2 Analyzed the PCM performances under the affection of piezoelectric and polymer"s material characteristic by FEM, and got the rule.3 Analyzed the PCM performances which affected by stickup layer"s materials characteristic and its thickness under the application of FEM.4 Based on the construction principles of 1-3 type orthotropic piezoelectric composite materials, the finite element model is designed and its orthotropy is analyzed, at the same time, the length/broad ratio to PCM orthotropy is also analyzed.

二、应用有限元法分析了压电相材料和聚合物基体相材料特性对于压电复合材料综合性能的影响规律。三、应用有限元法分析了粘贴层的材料性质和厚度尺寸对压电复合材料在实际应用中性能的影响规律。四、根据提出的正交异性压电复合材料的构造原理，设计出1-3型正交异性压电复合材料的有限元模型并分析其正交异性，同时分析了压电相材料长宽比对其正交异性的影响。

The decisive influencing factor of viscosity in carboxyl-methylation was cross-linking reaction. Carboxyl-methylation was the main influencing factor of solubility and swelling capacity in modification of high content amylose starch. The structure and gelatinization property of different amylose content were analyzed with an Olympus Vanox BHS-2 multi-function optic microscope, and the results were as follows. The structure of ordinary cornstarch was different from the high amylose; gelatinization temperature and pH value of starch were affected deeply by amylose content, but had little difference between the gelatinization of high content amylose starch contained 50% and 70% amylose; pH value had much more effect than temperature on the gelatinization of high content amylose cross-linked starch. Monochloroacetic acid consumption, alcohol concentration and pH value influenced the starch carboxyl-methylation. When alcohol concentration was 60%, pH value 10, monochloroacetic acid/starch mass ratio 55%, the carboxyl-methylation of high amylose cross-linked cornstarch had the best result. With the In-Vitro digestibility model and biodegradation experiment, the digestibility and biodegradability of high amylose cornstarch and its modified starch were detected.

采用Brabande粘度测定仪和Olympus Vanox BHS-2型多功能光学显微镜等分析手段对链淀粉含量50％和70％的高链玉米淀粉及其交联和交联羧甲基化淀粉的结构和性质进行了表征和分析，结果表明，普通玉米淀粉结构与含链淀粉50％和70％高链玉米淀粉结构不同；高链淀粉比普通淀粉难糊化，高链改性淀粉糊化受pH值影响较大，受温度影响较小；淀粉的冻融稳定性、透光率、溶解度、膨胀度和粘度受链淀粉的含量和改性的影响，但是，链淀粉含量超过50％时，则链淀粉含量对淀粉的膨胀度和溶解度影响不大；改性淀粉性质的影响因素中，影响粘度主要因素是交联反应，影响透明度、溶解度和膨胀度主要因素是羧甲基化改性；一氯乙酸用量、反应时乙醇浓度及碱性条件都会影响高链淀粉及其交联淀粉的羧甲基化改性效果，制备羧甲基化改性淀粉的最佳工艺是在pH值为10的60％的乙醇浓度介质中按一氯乙酸/淀粉质量比为55％进行取代反应。

The dilute hydrochloric acid concentration, Ti/clay ratio, H/Ti ratio, the pillaring reaction temperature, the aging time of pillaring agent and the initial concentration of clay greatly affect the formation of Ti-PILC.

结果表明，盐酸的浓度、Ti／土比、H／Ti比、交联温度、交联剂老化时间和粘土悬浮液浓度等制备条件对钛交联蒙脱石的物化性能有较大的影响。

This dissertation successfully fabricated cross-linked polysiloxanes under base catalysts such as potassium hydroxide siloxanolate or tetramethylammonium hydroxide (Me_4NOH) siloxanolate by anionic ring-opening copolymerization of cyclosiloxanes and Polyhedral Oligomeric Silsesquioxanes as multifunctional monomers.

本论文首次通过阴离子开环共聚，成功地将POSS大分子作为多官能团单体，与环硅氧烷在KOH硅醇盐或Me_4NOH硅醇盐等碱性催化剂的作用下，直接合成交联聚硅氧烷：通过调节POSS大分子和环硅氧烷单体的种类以及化学计量比，可合成出一系列不同种类和不同交联密度的交联聚硅氧烷；并对其阴离子开环共聚机理以及极性调节剂DMAc对凝胶时间的影响进行了详细讨论；同时借以凝胶含量和溶胀比、GPC、FT-IR、固体~(13)C和~(29)Si NMR、WAXD、DSC以及TG等手段对所得聚合物的微观结构以及热性能进行了详细考察。

The results show that the microscopical pore structure of the three dimensional orthogonal woven carbon fabric structure perform is composed of body-centered cubes which arranged periodically at spaces. The net structure and shape of the pores of perform are determined by the size and proration of the fasciculus diameter, which are key factors influencing the gaseous permeability and final density of composites. Once the proration of the fasciculus diameters of different directions is determined, the trend of diversification of the permeability followed by pore rate during CVI process and the density of composites are stated, and the permeability increases with the increase of the fasciculus diameter.

研究结果表明：三维正交结构炭纤维预制体的宏观孔隙结构在空间上可以看成是由呈周期性排列的体心立方&晶胞&构成； X ， Y 和 Z 3个方向纤维束直径大小及比例关系决定三维正交结构炭纤维预制体宏观孔隙网络的结构和形状，也是决定反应气体在孔隙中的比渗透率和复合材料最终致密度的重要因素；当 X ， Y 和 Z 3个方向纤维束直径的比例关系一定时，不同预制体在CVI增密过程中比渗透率随孔隙率变化的趋势相同；复合材料的最终致密度一定；比渗透率随纤维束直径增大而略有增大。

The molecular motion of amorphous region at high-frequency was found to be hardly affected during the stretching processes. In summary, elongation has created major but different influences on the morphology and molecular motion of the aforementioned four series of polymeric elastomers. For those elastomers like natural rubber and poly , elongation has induced crystallization of the noncrystalline or the soft segments. The crytallinitiy and the crystal thicknesses increase monotonously during the course of the stretching; On the other hand, the stretching processes for those semicrytalline copolymers like EMA and POE are rather complex, including the formation of crystal at relatively low λand the destruction of the crystal at the utmost λ. It revealed that stretching process has resulted in a decreasing of the thicknesses and a shortening of 〓C T〓s for the orthorhombic crystalline components.

拉伸对上述四个弹性体体系的聚集态结构都产生了很大影响，但是影响的程度和内容因体系而不同，对于本身存在着化学交联或者是物理交联的体系而言，拉伸导致了其中本来难以结晶组分的结晶，且结晶度随着拉伸比增加而增加，与此同时，体系结晶的晶片厚度也会逐渐增加；而对于结晶性共聚物体系，如EMA和POE，结晶区本来起到了物理交联的作用，在这种情况下拉伸的影响变得比较复杂，拉伸对于不同晶型的影响有所不同，在拉伸比较低的情况下体系总体的结晶度会有所增加，说明有新的结晶产生，当接近或达到断裂伸长比时，体系的结晶度会突然降低，含量占优的结晶会被拉伸所破坏，含量较低的结晶在整个拉伸过程中受的影响较小。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。