亚胺

N-p-tolylmaleimide is a kind of monomer to copolymerize with MMA to enhance the thermal stabilities of PMMA.In this article, NPTMI was prepared from the reaction of maleic anhydride and p-toluidine in one stage, which was testified by FTIR. The mp. of NPTMI was 154 and consistent with the literature.

目前国外对这方面的研究比较成熟，国内研究的较少，且还没有对N-对甲基苯基马来酰亚胺、MMA和第三单体丙烯腈或苯乙烯共聚以制备耐热PMMA树脂及其性能的研究。

The composite catalyzercan effectively catalyze cyclize reaction on the sysnthesis of N-phenyl maleimide.The yield of NPMI arrives at 90%,and the purity is 98.15%.

合成N-苯基马来酰亚胺的最佳工艺条件为；原料摩尔配比为1；1.2；溶剂为20；1；初期反应温度为40～50℃，环化反应温度为135℃；环化时间为2h。

The composite catalyzercan effectively catalyze cyclize reaction on the sysnthesis of N-phenyl maleimide.

合成N-苯基马来酰亚胺的最佳工艺条件为；原料摩尔配比为1；1.2；溶剂为20；1；初期反应温度为40～50℃，环化反应温度为135℃；环化时间为2h。

The reaction rates between VC/PMI and VC/N－cyclohexyl maleimide are compared, and the later is more rapid than the former.

并对VC/N－环己基马来酰亚胺和VC/PMI两个体系进行了比较。

Dealcoholization temperature markedly influences the surface area and porosity of the resultant MAO-supports. When the support was pretreated at lower or higher temperature, the corresponding MAO-support shows very low surface area;2.XRD and IR analyses indicate that MAO has reacted with the residual ethanol in the supports, which is an important manner to get MAO fixed on the carrier. Morever, XPS analyse indicates that MAO can also be coordinated with MgCl_2, which is another way to get MAO fixed on the support;3.ICP and EDX analyses indicate that dealcoholization temperature not only determined the element content on the solid catalyst, but also influences the element distribution on the carrier;4.The activities of the supported phenoxy-imine catalysts and the properties of resultant polymers are strongly dependent on the dealcoholization temperature. The support (MSP-5) obtained by treating MgCl_2·2.56C_2H_5OH at 160℃for 4 h, then modified by MAO is very effective for immobilizing complex 3, the resultant solid catalyst (MSPC-5) shows very high activity in ethylene polymerization, and its kinetics of polymerization is stable during the reaction process. Finally, PEs with spherical morphology and high bulk density (over 0.35g/ml) were obtained, without reactor fouling;5.In this work, polymerization conditions such as alkylaluminums, Al/Zr ratio, temperature and H_2 had a pronounced effect on the activity of MSPC-5 and properties of PE;(3). New MgCl_2-Supported Single-Site Catalysts for Ethylene PolymerizationIn this work, a kind of new MgCl_2 support was obtained by anhydrous MgCl_2 co-milled with solid MAO, and it is a creative contribution. Then some single-site catalysts were supported on the new MgCl_2 support, and the resulted solid catalysts were tested in ethylene polymerization, the results indicated that:1.XRD and IR analyses indicate that MAO does be coordinated with MgCl_2, which is in good agreement with the results obtained by XPS;2.co-mlling time had no obvious effect on the texture of support after 12 hours;3.In this work, MgCl_2 was co-milled with solid MAO for different hours, and then complex 3 was supported on these co-milled supports. It was found that co-milling time markedly influences the activity of solid catalysts, but it had negligible effect on the kinetic profile and the properties of resultant PE.

XPS研究结果表明，MAO不仅仅只和乙醇作用，MAO还与MgCl_2本身有一定的作用，这是一个极为重要的发现；3、通过ICP和EDX表征，发现载体的脱醇温度直接影响着元素在固体催化剂中的含量及分布；4、脱醇温度极大地影响着负载苯氧基亚胺类催化剂的活性和聚合物的性能，特别是原始载体经160℃活化4小时制备得到的固体催化剂MSPC-5的活性明显高于其他脱醇温度条件下制得的固体催化，并且催化剂寿命长，表现出稳定的动力学行为，最终获得了高堆密度(大于0.35g／ml)的球形聚乙烯颗粒；5、本文选择MSPC-5为研究对象，考察了聚合反应参数对催化剂的活性及其聚合物的影响，研究发现：不同的烷基铝对催化剂具有非常重要的影响，特别足TIBA对MSPC-5的助催化活性最高，烷基铝的加入量有一个较佳值，聚合温度为80度时活性最高，H_2的加入使催化剂的活性明显降低且聚合物的分子量也减小；、新型氯化镁载体负载单活性中心催化剂催化乙烯聚合本文创造性采用固体MAO与无水氯化镁直接进行共研磨，制备出了一种的新型的氯化镁载体，并将该载体用于多种单活性中心催化剂的负载化研究，研究表明：1、通过BET、XRD的表征，再次证实了MAO与MgCl_2之间具有直接作用，与XPS的研究结果相一致；2、当研磨时间高于12小时时，延长研磨时间对载体的结构没有显著的影响；3、将配合物3负载于共研磨时间不同的一系列载体上，乙烯聚合结果表明，尽管共研磨时间对负载催化剂的活性具有明显的影响，但是它对聚合物的性能以及催化剂的影响不明显。

Dealcoholization temperature markedly influences the surface area and porosity of the resultant MAO-supports. When the support was pretreated at lower or higher temperature, the corresponding MAO-support shows very low surface area; 2.XRD and IR analyses indicate that MAO has reacted with the residual ethanol in the supports, which is an important manner to get MAO fixed on the carrier. Morever, XPS analyse indicates that MAO can also be coordinated with MgCl_2, which is another way to get MAO fixed on the support; 3.ICP and EDX analyses indicate that dealcoholization temperature not only determined the element content on the solid catalyst, but also influences the element distribution on the carrier; 4.The activities of the supported phenoxy-imine catalysts and the properties of resultant polymers are strongly dependent on the dealcoholization temperature. The support (MSP-5) obtained by treating MgCl_2·2.56C_2H_5OH at 160℃for 4 h, then modified by MAO is very effective for immobilizing complex 3, the resultant solid catalyst (MSPC-5) shows very high activity in ethylene polymerization, and its kinetics of polymerization is stable during the reaction process. Finally, PEs with spherical morphology and high bulk density (over 0.35g/ml) were obtained, without reactor fouling; 5.In this work, polymerization conditions such as alkylaluminums, Al/Zr ratio, temperature and H_2 had a pronounced effect on the activity of MSPC-5 and properties of PE;(3). New MgCl_2-Supported Single-Site Catalysts for Ethylene Polymerization In this work, a kind of new MgCl_2 support was obtained by anhydrous MgCl_2 co-milled with solid MAO, and it is a creative contribution. Then some single-site catalysts were supported on the new MgCl_2 support, and the resulted solid catalysts were tested in ethylene polymerization, the results indicated that: 1.XRD and IR analyses indicate that MAO does be coordinated with MgCl_2, which is in good agreement with the results obtained by XPS; 2.co-mlling time had no obvious effect on the texture of support after 12 hours; 3.In this work, MgCl_2 was co-milled with solid MAO for different hours, and then complex 3 was supported on these co-milled supports. It was found that co-milling time markedly influences the activity of solid catalysts, but it had negligible effect on the kinetic profile and the properties of resultant PE.

XPS研究结果表明，MAO不仅仅只和乙醇作用，MAO还与MgCl_2本身有一定的作用，这是一个极为重要的发现； 3、通过ICP和EDX表征，发现载体的脱醇温度直接影响着元素在固体催化剂中的含量及分布； 4、脱醇温度极大地影响着负载苯氧基亚胺类催化剂的活性和聚合物的性能，特别是原始载体经160℃活化4小时制备得到的固体催化剂MSPC-5的活性明显高于其他脱醇温度条件下制得的固体催化，并且催化剂寿命长，表现出稳定的动力学行为，最终获得了高堆密度(大于0.35g／ml)的球形聚乙烯颗粒； 5、本文选择MSPC-5为研究对象，考察了聚合反应参数对催化剂的活性及其聚合物的影响，研究发现：不同的烷基铝对催化剂具有非常重要的影响，特别足TIBA对MSPC-5的助催化活性最高，烷基铝的加入量有一个较佳值，聚合温度为80度时活性最高，H_2的加入使催化剂的活性明显降低且聚合物的分子量也减小；、新型氯化镁载体负载单活性中心催化剂催化乙烯聚合本文创造性采用固体MAO与无水氯化镁直接进行共研磨，制备出了一种的新型的氯化镁载体，并将该载体用于多种单活性中心催化剂的负载化研究，研究表明： 1、通过BET、XRD的表征，再次证实了MAO与MgCl_2之间具有直接作用，与XPS的研究结果相一致； 2、当研磨时间高于12小时时，延长研磨时间对载体的结构没有显著的影响； 3、将配合物3负载于共研磨时间不同的一系列载体上，乙烯聚合结果表明，尽管共研磨时间对负载催化剂的活性具有明显的影响，但是它对聚合物的性能以及催化剂的影响不明显。

Its main products include:ZOLEDRONIC ACID, ADAPALENE, SIMDAX, VORICONAZOLE, J ACID UREA, J ACID UREA SODIUM SALT, 1,7-CLEVE'S ACID, 1,6-CLEVE'S ACID, 1,5- DINAPHTHYL ISOCYANATE, 5- INROINDOLE,----2-METHOXYIMINO-2-（FURYL-2-YL）ACETIC ACID AMMONIUM SALTand etc.

部分产品远销美国、德国、英国、印度、日本等十几个国家和地区，主要产品有：唑来磷酸、阿达帕林、左西孟旦、伏立康唑、猩红酸、猩红酸钠盐、双介酸、1，7克力夫酸1，6克力夫酸、1，5-萘二异氰酸酯、5-硝基吲哚、甲氧亚胺基呋喃乙酸铵等。

Utilizing 6 and several kinds of diazides prepared in our lab, polys containing 1,2,3-triazolyl and perfluorocyclobutane units were synthesized by "Click chemistry". Utilizing the polycondensation reaction between 6 and several commercially available aromatic diphenol or copolymerization reaction after adding another active aromatic dichloride, fluorinated polys containing phenylphosphine oxide units were synthesized. Utilizing the polycondensation reaction between 6 and several commercially available aromatic dianhydride, fluorinated polys containing PPO units were synthesized.Secondly, structure characterization of fluorinated polys.

利用化合物6同各种自制的二叠氮化合物，通过&Click chemistry&，合成了具有1，2，3-三唑环结构单元的全氟环丁基类聚芳醚；利用化合物22同各种商业化的芳香二元酚类化合物进行缩聚反应或者再加入另外一种活性芳香二氯代物进行三元共聚反应，制备了具有苯基氧膦结构单元的含氟聚芳醚；通过化合物25同各种商业化的芳香二元酸酐类化合物进行缩聚反应，得到了具有PPO结构单元的含氟聚醚酰亚胺。

The cross-linked PHBV was obtained by means of γ-radiation with N, N'-4, 4'-diphenylmethane bismaleimide .

用交联助剂二苯甲撑双马来酰亚胺实现了PHBV的γ-辐射交联。

Some non-coded a , a -disubstituted amino acids could be obtained with up to 75.3% ee by using ketone imino esters as nueclophilles in the allylic alkylation reaction.

当利用亚胺的氨基酸酯衍生物时，可以得到一些非天然的季碳氨基酸衍生物， ee 值最高可以达到75.3%。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。