亚乙烯基

New contributions of this work are as follows:(1). Preparation of Spherical MgCl_2-Supported Late-Transition Metal Catalysts for Ethylene PolymerizationFacile and effective immobilization of late-transition metal catalysts. 2,3-bis-(2,6-diisopropylphenyl) butane diimine nickel dibromide (1) and 2,6-bis-[1-(2,4,6-trimethylphenylimino)ethyl]pyridine iron dichloride (2), for ethylene polymerization has been achieved, using spherical MgCl_2 supports obtained by thermal dealcoholization of MgCl_2·2.56C_2H_5OH, and the effects of dealcoholization temperature on supported late-transition metal catalysts and the properties of resultant polymers were studied, the results indicated that:1.Supports with appropriate mechanical strength, high surface area and high porosity could be prepared by thermal dealcoholization of spherical MgCl_2·2.56C_2H_5OH supports; 2.BET, XRD, IR, SEM, GPC and DSC analyses indicate that the activities of the supported late-transition metal catalysts and the properties of resultant polymers are strongly dependent on the dealcoholization temperature.

本工作的新贡献如下：(1)、球形氯化镁负载后过渡金属催化荆催化乙烯聚合本文将配合物2，3-双(2，6-二异丙基苯亚胺)丁烷二溴化镍(1)和配合物2，6-二[1-(2，4，6-三甲基苯亚胺)乙基]吡啶二氯化铁(2)分别直接负载于经不同热脱醇温度处理的球形氯化镁载体上，研究了氯化镁载体的脱醇温度对负载化后过渡金属催化剂及其聚合物的影响，研究表明：1、通过对球形MgCl_2·2.56C_2H_5OH载体进行热脱醇处理，可以获得合适机械强度、较高比表面积和较高孔隙度的球形氯化镁载体；2、BET，XRD，IR，SEM，GPC和DSC研究表明，脱醇温度极大地影响负载后过渡金属催化剂的活性和聚合物的性能。

New contributions of this work are as follows:(1). Preparation of Spherical MgCl_2-Supported Late-Transition Metal Catalysts for Ethylene Polymerization Facile and effective immobilization of late-transition metal catalysts. 2,3-bis-(2,6-diisopropylphenyl) butane diimine nickel dibromide (1) and 2,6-bis-[1-(2,4,6-trimethylphenylimino)ethyl]pyridine iron dichloride (2), for ethylene polymerization has been achieved, using spherical MgCl_2 supports obtained by thermal dealcoholization of MgCl_2·2.56C_2H_5OH, and the effects of dealcoholization temperature on supported late-transition metal catalysts and the properties of resultant polymers were studied, the results indicated that: 1.Supports with appropriate mechanical strength, high surface area and high porosity could be prepared by thermal dealcoholization of spherical MgCl_2·2.56C_2H_5OH supports; 2.BET, XRD, IR, SEM, GPC and DSC analyses indicate that the activities of the supported late-transition metal catalysts and the properties of resultant polymers are strongly dependent on the dealcoholization temperature.

本工作的新贡献如下：(1)、球形氯化镁负载后过渡金属催化荆催化乙烯聚合本文将配合物2，3-双(2，6-二异丙基苯亚胺)丁烷二溴化镍(1)和配合物2，6-二[1-(2，4，6-三甲基苯亚胺)乙基]吡啶二氯化铁(2)分别直接负载于经不同热脱醇温度处理的球形氯化镁载体上，研究了氯化镁载体的脱醇温度对负载化后过渡金属催化剂及其聚合物的影响，研究表明： 1、通过对球形MgCl_2·2.56C_2H_5OH载体进行热脱醇处理，可以获得合适机械强度、较高比表面积和较高孔隙度的球形氯化镁载体； 2、BET，XRD，IR，SEM，GPC和DSC研究表明，脱醇温度极大地影响负载后过渡金属催化剂的活性和聚合物的性能。

The surface hydroxyl group onto magnetic polyvinyl acetate nanoparticles can be obtained by saponification reaction on their surface.

结果表明，磁性聚苯乙烯颗粒与丁二酸酐发生Freidel-Crafts酰基化反应，可以在颗粒表面引入少量羧基；磁性聚甲基丙烯酸甲酯颗粒分别与乙二醇、二缩三乙二醇、聚乙二醇等发生醇-酯交换反应，可以在颗粒表面接枝不同分子链长度的末端羟基；磁性聚醋酸乙烯酯颗粒经过醇解或皂化反应可以获得表面羟基；磁性聚丙烯酸甲酯颗粒通过乙二胺或1，6己二胺的胺解反应可以得到表面氨基，继而与一氯乙酸反应可以引入亚胺二乙酸基团。

Dealcoholization temperature markedly influences the surface area and porosity of the resultant MAO-supports. When the support was pretreated at lower or higher temperature, the corresponding MAO-support shows very low surface area; 2.XRD and IR analyses indicate that MAO has reacted with the residual ethanol in the supports, which is an important manner to get MAO fixed on the carrier. Morever, XPS analyse indicates that MAO can also be coordinated with MgCl_2, which is another way to get MAO fixed on the support; 3.ICP and EDX analyses indicate that dealcoholization temperature not only determined the element content on the solid catalyst, but also influences the element distribution on the carrier; 4.The activities of the supported phenoxy-imine catalysts and the properties of resultant polymers are strongly dependent on the dealcoholization temperature. The support (MSP-5) obtained by treating MgCl_2·2.56C_2H_5OH at 160℃for 4 h, then modified by MAO is very effective for immobilizing complex 3, the resultant solid catalyst (MSPC-5) shows very high activity in ethylene polymerization, and its kinetics of polymerization is stable during the reaction process. Finally, PEs with spherical morphology and high bulk density (over 0.35g/ml) were obtained, without reactor fouling; 5.In this work, polymerization conditions such as alkylaluminums, Al/Zr ratio, temperature and H_2 had a pronounced effect on the activity of MSPC-5 and properties of PE;(3). New MgCl_2-Supported Single-Site Catalysts for Ethylene Polymerization In this work, a kind of new MgCl_2 support was obtained by anhydrous MgCl_2 co-milled with solid MAO, and it is a creative contribution. Then some single-site catalysts were supported on the new MgCl_2 support, and the resulted solid catalysts were tested in ethylene polymerization, the results indicated that: 1.XRD and IR analyses indicate that MAO does be coordinated with MgCl_2, which is in good agreement with the results obtained by XPS; 2.co-mlling time had no obvious effect on the texture of support after 12 hours; 3.In this work, MgCl_2 was co-milled with solid MAO for different hours, and then complex 3 was supported on these co-milled supports. It was found that co-milling time markedly influences the activity of solid catalysts, but it had negligible effect on the kinetic profile and the properties of resultant PE.

XPS研究结果表明，MAO不仅仅只和乙醇作用，MAO还与MgCl_2本身有一定的作用，这是一个极为重要的发现； 3、通过ICP和EDX表征，发现载体的脱醇温度直接影响着元素在固体催化剂中的含量及分布； 4、脱醇温度极大地影响着负载苯氧基亚胺类催化剂的活性和聚合物的性能，特别是原始载体经160℃活化4小时制备得到的固体催化剂MSPC-5的活性明显高于其他脱醇温度条件下制得的固体催化，并且催化剂寿命长，表现出稳定的动力学行为，最终获得了高堆密度(大于0.35g／ml)的球形聚乙烯颗粒； 5、本文选择MSPC-5为研究对象，考察了聚合反应参数对催化剂的活性及其聚合物的影响，研究发现：不同的烷基铝对催化剂具有非常重要的影响，特别足TIBA对MSPC-5的助催化活性最高，烷基铝的加入量有一个较佳值，聚合温度为80度时活性最高，H_2的加入使催化剂的活性明显降低且聚合物的分子量也减小；、新型氯化镁载体负载单活性中心催化剂催化乙烯聚合本文创造性采用固体MAO与无水氯化镁直接进行共研磨，制备出了一种的新型的氯化镁载体，并将该载体用于多种单活性中心催化剂的负载化研究，研究表明： 1、通过BET、XRD的表征，再次证实了MAO与MgCl_2之间具有直接作用，与XPS的研究结果相一致； 2、当研磨时间高于12小时时，延长研磨时间对载体的结构没有显著的影响； 3、将配合物3负载于共研磨时间不同的一系列载体上，乙烯聚合结果表明，尽管共研磨时间对负载催化剂的活性具有明显的影响，但是它对聚合物的性能以及催化剂的影响不明显。

The invention relates to a pipeline polyurea outer anticorrosive coating and the making method thereof, making heated prepolymerization reaction on dibenzo-methane diisocyanate, carbodiimide diisocyanate, polyether binary alcohol and polyether trihydric alcohol to prepare prepolymer solution A, and making end amino polyethylene oxide ether, dimethyl sulfur-based toluene diamine, diethyl diamine, iso-propyl titanate solution, polyacrylate, carbon black, titanium dioxide and lightweight calcium carbonate into solution B, and as using, respectively heating the solutions A and B to 65 deg.C and then mixing them, then quickly spraying and curing to form a coat.

本发明涉及一种管道用聚脲外防腐涂料及制造方法，由二苯基甲烷二异氰酸酯、碳化二亚胺化二异氰酸酯、聚醚二元醇和聚醚三元醇通过加热预聚反应制成预聚物的A液、由端氨基聚氧化乙烯醚、二甲硫基甲苯二胺、二乙基甲苯二胺、钛酸异丙酯溶液、聚丙烯酸酯溶液、碳黑、钛白粉和轻质碳酸钙配制而成的B液组成，使用时将A液和B液分别加热至65℃后混合，然后快速喷涂固化形成涂层。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。