乙烯基树脂

The processing of glass-reinforced plastic cover for Model 16 Hooker electrolyzer with vinyl ester based unsaturated polyester resin was introduced.

叙述了用乙烯基酯不饱和聚酯树脂制作虎克－16型玻璃钢电解槽盖的施工方法，介绍了乙烯基酯不饱和聚酯树脂的性能。

Resin transfer molding mould was manufactured with bisphenol-A epoxide vinylester resin as matrix,poly as low shrinkage additive and glass fiber tricot as reinforcing material,according to the basic requirement of matrix resin of RTM mould.

根据树脂传递模塑模具对基体树脂的基本要求，选用双酚A环氧乙烯基酯树脂为基体，聚乙酸乙烯酯为低收缩添加剂，玻璃纤维经编织物为增强材料，并加入相应的助剂，制备了复合材料RTM模具。

The Solidification temperature range was defined as 110-200℃ by DSC analysis. More accelerant used can increase the casing samples dynamic performance, but more than enough accelerant can induce a severe solidified reaction that result in a smaller polymeric meshwork and reducing the sample's performance. Normally the Accelerant dosage can be 2 portions; The Epoxy resin CFRP has a obvious better performances than the Vinyl-ester Resin CFRP, i.e. had a Bend Strength of 1516MPa, LSS of 85MPa, also Tg raised to 195~C~ When used the end-carboxyl polyether to reinforce the epoxy resin, the casing sample's SS, BS and Crack Elongation all increased geminately. The CFRP performance also increased a little, that is because the performance of the CFRP mainly contributed by the CF. The reinforced resin improved the interface between the CF and resin that contribute to the little increasing.

通过DSC分析确定了该环氧树脂的固化温度范围为110~200℃，促进剂增加会提高浇注体力学性能，但过多的促进剂会使固化反应剧烈，聚合网络减小，使浇注体性能下降，一般用量为2份左右；以环氧树脂为基体的复合材料性能明显比以乙烯基酯树脂的性能提高，弯曲强度达到1516MPa，层间剪切强度达到85MPa，同时Tg也上升到195℃；用端羧基聚醚增韧环氧树脂后，其浇注体的拉伸强度、弯曲强度及断裂伸长都成倍增加，复合材料的性能也有所提高，但提高幅度不大，因为复合材料的力学性能主要由碳纤维承担，树脂增韧后改善了复合材料的界面性能。

Hydrophobic-hydrophilic macroporous polydivinylbenzene/polyacrylethylenediamine interpenetrating polymer networks (PDVB/PAEM IPN) were prepared by the sequential suspension polymerization method. These were composed of two networks, of which one was hydrophobic and the other was hydrophilic. The objective of this work was to study the adsorption thermodynamics and adsorption kinetics of this hydrophobic- hydrophilic IPN. The focus was on adsorption isotherms of vanillin at different temperatures, and these fit well into the Freundlich adsorption isotherm. The isosteric adsorption enthalpy, adsorption Gibbs free energies and the adsorption entropy could be calculated according to thermodynamic functions.

采用分步悬浮聚合法制备了具有疏水性能的聚二乙烯基苯(polydivinylbenzene， PDVB)为第一网，具有亲水性能的聚丙烯酰乙二胺(polyacrylethylenediamine， PAEM)为第二网的疏水／亲水大孔聚二乙烯基苯／聚丙烯酰乙二胺互穿聚合物网络(interpenetrating polymer networks， IPN)，研究这类疏水／亲水IPN组成的树脂对吸附质的吸附热力学和吸附动力学；测定了该树脂对香兰素在不同温度下的吸附等温线，吸附等温线符合Freundlich等温吸附方程，利用热力学函数关系计算出了吸附焓、自由能和熵变。

Acrylic resin containing N,N-dimethyl amino group and vinyl group applicable for UV-curable and cathodic electrophoretic paint was synthesized via radical polymerization of acrylic monomers followed by modification with methacrylic oxyethyl isocyanate.

通过自由基共聚合得到丙烯酸树脂，然后用甲基丙烯酸异氰酸乙酯对其改性，合成了既带有N，N-二甲胺基，又带有乙烯基的紫外光固化阴极电泳漆基体树脂。

The effects of MMA and alumina trihydrate on properties of oligourethane methacrylate resins were investigated. And the curing reactivities of unsaturated polyester resin, vinyl ester and UM resin were compared by various methods.

研究了甲基丙烯酸甲酯和三水合氧化铝含量对聚氨酯甲基丙烯酸酯树脂性能的影响，比较了不饱和聚酯树脂、乙烯基树脂和UM树脂的固化反应活性。

Woven Rovings are compatible with many resin systems such as polyester,vinyl ester, epoxy and phenolic resins.

无捻粗纱布适用于各种树脂增强系统，如不饱和聚酯树脂，乙烯基树脂，环氧树脂和酚醛树脂等。

E-Glass Woven Rovings are compatible with many resin systems such as polyester, vinyl ester, epoxy and phenolic resins.

无碱无捻粗纱布适用于各种树脂增强系统，如不饱和聚酯树脂、乙烯基树脂、环氧树脂和酚醛树脂等。

The morphological structure of cured vinyl-ester resin and the formation of two-phase structures in vinyl-ester resin has been studied by using SEM and differential scanning calorimetry.The results demonstrated the existence of clusters of gel-particles with a size of about 20 μ m,each cluster of gel-particles containing many gel-particles with coral-like structures.The formation of gel-particles resulted in two-phase structure characterized by the two peaks in the rescanned DSC thermographs of the resin. The cure conditions (temperatures,post-cure) affected microstructure in the cured resins.

采用SEM、DSC研究了乙烯基酯树脂固化过程中凝胶粒子的形成过程及两相结构对固化放热的影响，结果表明，凝胶粒子在固化树脂中呈群状分布，每群凝胶粒子的最大尺寸为20μ m左右，每群凝胶粒子由许多独立凝胶粒子组成；凝胶粒子的形成使树脂产生了两相结构，使树脂的恒温DSC残余放热呈双峰分布；树脂的固化条件影响其微观结构。

The corresponding relations between the strain of the static state and dynamic cycle load and the volume resistance of the short chopped carbon fibers, short chopped carbon mat, unidirectional carbon fibers reinforced vinyl resin composites is existed. The physical modes of these kinds of composites are also designed based on the experiment data. The resistance and strain of the short chopped fibers reinforced vinyl composites satisfy the equation of y =A + Bx + Cx~2 in the static strain test method and the short chopped mat reinforced vinyl composites is y = A + Bx.

短切碳纤维、短切碳纤维毡、单向碳纤维增强乙烯基酯树脂复合材料在静态和动态循环载荷下，应变与电阻之间有较好的对应性，同时根据实验数据，建立了不同条件下该复合材料应变和电阻变化规律的物理模型，短切碳纤维增强乙烯基酯树脂复合材料在静态拉伸时电阻与应变之间满足：y=A+Bχ+Cχ~2；碳纤维毡增强乙烯基酯树脂复合材料在静态拉伸破坏时电阻与应变之间满足：y=A+Bχ。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。