主轴箱

At the end of the analysis, it is suggested that exerting the elastic and damping restriction on the afterbody of the headstock was the best reasonable measurement.

通过各参数的比较分析，从而得出在系统动响应最小情况下，在主轴箱尾部施加弹性阻尼约束是最佳的改进措施。

As magin use is to arrange the position of all the mational axle box and transrnit the power and the motion to all the main axle by the electrical machinery or the power pants .

三组合机床主轴箱设计，按专用要求进行设计，由通用零件组成，其主要作用是根据被加工零件的要求，安排各主轴位置并将动力和运动由电机或动力部件传给各主轴，使之得到要求的转速，机床主轴箱选用400*400，用中间传动轴带动主轴传动。

To design it a cocording to the special 's made up of the mational magin use is to arrange the position of all the mational axle box and transrnit the power and the motion to all the main axle by the electrical machinery or the power pants .

三组合机床主轴箱设计，按专用要求进行设计，由通用零件组成，其主要作用是根据被加工零件的要求，安排各主轴位置并将动力和运动由电机或动力部件传给各主轴，使之得到要求的转速，机床主轴箱选用400*400，用中间传动轴带动主轴传动。

T he operating platform is located in front of the headstock and can be elevated independent of it.

操作平台安置于主轴箱的前面，并能独立于主轴箱进行升降。

And productivity and calculate the card bore and make the lathe up to design including processing the process picture of the part, processed sketch map, lathe to contact size picture and and the calculated card of productivity, named " three pictures and one calorie " that usually spoken are designed; Many axle case part is it include many axle case design primitive drawing, main shaft choice and power calculate, design of transmission and calculate, etc., structure of form that basis pursue mainly to design.

粗镗组合机床总体设计包括被加工零件工序图、加工示意图、机床联系尺寸图和生产率计算卡，即通常所说的&三图一卡&设计；主轴箱部件设计主要包括主轴箱设计原始依据图的绘制、主轴结构形式的选择及动力计算、传动系统的设计与计算等。

And productivityand calculate the card bore and make the lathe up to designincluding processing the process picture of the part, processedsketch map, lathe to contact size picture and and the calculatedcard of productivity, named " three pictures and one calorie " thatusually spoken are designed; Many axle case part is it include manyaxle case design primitive drawing, main shaft choice and powercalculate, design of transmission and calculate, etc., structure ofform that basis pursue mainly to design.

粗镗组合机床总体设计包括被加工零件工序图、加工示意图、机床联系尺寸图和生产率计算卡，即通常所说的&三图一卡&设计；主轴箱部件设计主要包括主轴箱设计原始依据图的绘制、主轴结构形式的选择及动力计算、传动系统的设计与计算等。

The thesis designs that PLC controls four servo electric motors using Aimosheng EC20H , the rocker arm realizing beam drill goes up and down , the rocker arm rotates , the main spindle box slides , the chief axis moves forward to give axial four action , PLCs the motion controlling one frequency conversion electric motor at the same time realizing the machine tool host moving the revolution being a chief axis.

本论文设计使用艾默生EC20H PLC控制四台伺服电机，实现摇臂钻床的摇臂升降、摇臂旋转、主轴箱滑动、主轴进给四个轴向的动作，PLC同时控制一台变频电机实现机床的主运动即主轴的旋转运动。

When the spindle box cutter left Move right back to the workpiece, the rotary table 90 degrees, and then the left spindle box again.

当主轴箱右移退回到刀具离开工件后，工作台回转90度，然后主轴箱再次左移。

This article elaborated a 12 level of rotational speed C6132 horizontal lathe headstock design process, the headstock uses to support the main axle and to cause it revolving.

本文阐述了一个12级转速的C6132卧式车床主轴箱的设计过程，主轴箱用以支撑主轴并使之旋转。

This thesis combination machine for design processing many stalks the box ten screw threads of rights the bore bed.

车床主轴箱箱体右侧10-M8螺纹底孔组合钻床设计摘要：本论文为加工主轴箱箱体右侧十个螺纹底孔的组合钻床的设计。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。