主要元件

Electromagnetic coil is the most important components, it is converted to electrical energy of the core mechanical motion.

电磁线圈是其最主要的元件，由它将电能转换为铁芯的机械运动。

The main content is AT89S51 control of the core components, design of a electronic organ.

本文的主要内容是用AT89S51单片机为核心控制元件，设计一个电子琴。

We present some new topologies of components and devices, embedded passive circuits and interconnections with good EM properties which can meet development of microwave and millimeter wave LTCC technology and domestic state of arts and crafts inland. These algorithms are applied to optimization of LTCC circuits by using relevant production and applicable techniques in SM study, i.e. optimizing and designing various LTCC capacitors and inductances by original space mapping, LTCC transitions by aggressive space mapping and equivalent lumped-element LTCC filters by knowledge-based aggressive space mapping and neural space mapping.

并且针对微波、毫米波LTCC技术发展需要和国内加工水平，探索具有良好电磁特性的新型组件拓扑结构及其内嵌无源电路、互连实现形式，利用在空间映射研究中取得的成果和开发的实用技术，实现LTCC电路的优化，主要是采用初始空间映射方法优化设计了LTCC电容电感、采用主动空间映射方法LTCC过渡、采用基于知识主动空间映射方法与神经网络空间映射方法优化设计了LTCC等效集总元件滤波器等。

This study focuses on the chain for the multi-speed bicycle. Design space for the freewheel on bicycle is limited by frame, riding posture, etc. However, the number of gear ratios in this design space increased with added more sprockets are the trend on the bicycles.

本论文主要研究对象为自行车上传动系统中的链条元件，由於自行车飞轮受到车架、骑乘姿势所形成的空间限制，必须在有限空间内增加飞轮片数增加齿数比，达到变速换档的舒适性。

The Joint elements of pneumatic clutch adopted friction disc, friction blocks etc.

气动离合器接合元件主要采用摩擦片，摩擦块等。

Nowadays, enhanced heat transfer utilizes superior heat transfer elements. Spirally grooved tube is one of them.

目前，强化传热主要是采用性能良好的传热元件，螺旋槽管是其中的一种。

In the market, various forms of hair-dryer can see, but its internal structure is largely the same mainly by the motor and its drive blower fans, heating elements and electrical control switch pieces of three major components.

在市场上，各种样式的电吹风都能见到，但它的内在结构大致一样，主要由电动机和它的驱动风叶、发热元件及电器控制开关件三大部分组成。

The main purpose of this thesis is to hope to electro-plating 3D micro-structure like small components of three-dimensional space , such as little spring , in charge of hollowly ,etc.

本论文的主要目的是希望析镀出3D微结构(像微弹簧、空心管等三度空间微小元件)，而著手研究『3D微电镀』的可行性，为此目标而开发3D阳极引导微电镀系统。

Taken the three dimensional shining metal combination machine tool as an object of study in the paper,the main structure and motion form have been discussed and the work process and control requirement of machine tool have been analyzed,the movement cycle diagram of machine tool and the motion table of hydraulic pressure component have been given.Then the control system design based on PLC has been proposed,the I/O address table has been listed and the hardware and software of the control system has been de...

文章以三面铣组合机床为研究对象，通过对主要结构和运动形式的探究以及对机床的工作过程和控制要求分析，给出了机床动作循环图、液压元件动作表；并采用PLC控制系统的设计方法，列出了I/O地址分配表，进行了软硬件设计，绘制了 PLC的外部接线图和单循环自动工作流程图及其说明；实验运行结果表明，将PLC技术应用于三面铣组合机床具有整体技术及经济效益。

The course of the localization and running condition of CANDU-6 fuel bundle production line for HWR Nuclear Power Station—Baotou Nuclear Fuel Plant, is presented.

介绍了我国第一条重水堆核电站用CANDU6燃料棒束生产线———包头核燃料元件厂的建设历程和运行状况，描述了CANDU 6型燃料棒束的技术特征、制造工艺流程及主要工艺技术条件要求。

Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.

在对危险的南部地区访问时，他斥责什叶派民兵领导人对中央集权的挑衅行为。

In fact,I've got him on the satellite mobile right now.

实际上 我们已接通卫星可视电话了