中间相

The specimens sintered under air atmosphere appear the obvious layering phenomenon, on the whole,and which can be divided into the surface protection layer, the center layer and the non-oxidized layer,SiAlON phase comes into being at about 1550℃,the crystal shape of them is columnar; The specimens sintered carbon reduction atmosphere have no obvious layering phenomenon, the formation temperature of SiAlON is about 1600℃, the crystal shape of them is acicular,fibriform or anomalous.

氧化气氛下，烧成的试样出现明显的分层现象，大致上可以分为表面保护层、中间层和非氧化层，SiAlON相的形成温度约在1550℃左右，多呈柱状；还原气氛下，试样无明显的分层现象，SiAlON相的形成温度约在1600℃左右，多呈针状、纤维状或不规则状。

It is shown that, as a result of the interstitial impurities, the number of atomic states increases, bond structures become seriously anisotropic,β→α transformation becomes hindered, and the phase transformation in the intermediate content becomes very complex.

表明，间隙杂质提高了合金元素的原子杂阶，引起键结构呈严重的各向异性，阻碍了β→α相转变，导致中间成分相变的复杂性。

By extending the VBG external cavity length, and inserting a convex cylindrical lens between external cavity and LDA for transmiting. Phase-locked of external cavity is achieved by tilting of Bragg Grating external cavity. Experiment studied the stability of the in-phase mode far-field output at 35A. Wavelength is locked at 802 nm. The Full-Width Half-Maximum of locked specrum narrowed to 0.2 nm and the corresponding far-field divergence angle is 1.8 mrad.

通过拉长VBG外腔腔长，在VBG外腔和LDA中间插入平凸柱面透镜，采用偏转体布拉格光栅外腔进行外腔锁相研究，在注入电流35A时，获得稳定的同相单瓣模远场输出，波长锁定在802nm，中心主瓣峰值半宽压窄到0.2nm，对应的远场发散角为1.8mrad。

By dilatometric test, Laboratory experiments were...

利用膨胀法在Thermecmastor-Z型热/力模拟试验机上进行实验室实验，测定了研究钢种在不同的中间保温工艺及一定变形工艺条件下的过冷奥氏体连续冷却转变曲线；对每个试样进行了打磨、抛光、腐蚀，在光学显微镜下观察其组织，研究了在不同中间保温工艺下组织的变化情况；利用所建立的CCT曲线研究了一定变形工艺条件及不同保温工艺对其相变行为及组织的影响，对其影响规律进行了分析。

This article according to the characteristic of traditional signature and stamper, combinic the demands of signature and seal in e-Government-affair work information system, inosculates the technology of middleware and e-Government-affair security, makes use of Object Oriented and component technology, integrates correlation knowledge of compositive cryptogram, PKI, seal digital image, ActiveX etc, studies and achieves digital e-signature-seal middleware based on Web which is used in Internet/Intranet environment.

本文根据传统签名、盖章的特点，结合高校、政府等办公信息系统中的盖章签名需求，把WEB安全技术和中间件技术相融合，利用面向对象和组件技术，集成密码学、公开密钥体系PKI、印章数字图像、ActiveX控件等相关知识，研究并设计了一个应用于Internet/Intranet环境中的基于WEB的电子印章中间件。

A handle is arranged in the middle of the frame, and the handle is connected with a big bevel wheel through a small bevel wheel.

它包括框架、左伸缩臂、右伸缩臂，所述框架为中间空形，所述左伸缩臂和右伸缩臂的内侧为管形，外侧为蝶形，蝶形面上设有二排孔，所述框架两端分别嵌套左伸缩臂内侧和右伸缩臂内侧，左伸缩臂内顶端设置有左螺母，右伸缩臂内顶端设置有右螺母，所述的框架中部设有手柄，手柄通过小斜齿轮连接大斜齿轮，大斜齿轮连接有螺杆，所述螺杆有以中间为对向的螺纹，螺杆的两端分别与左螺母和右螺母相连接。

During the course of experimentation the order of charging、the superheating temperature of aluminum melt、the temperature of holding、stirring and etc will be researched, who will affect the absorptivity of the elements in the master alloy Al-Ti-B-Re, and who will affect the shape、size and the distribution of the second phase; It will also be researched that the effect of the rear-earth to the declining of refiner、to the remelting property and to the refining property.

在实验中主要探讨了加料次序、熔体过热温度、静置温度、搅拌等工艺参数对Al-Ti-B-Re中间合金中各种元素吸收率的影响，对Al-Ti-B-Re中间合金组织中第二相形态、尺寸、分布及细化效果的影响；稀土元素对细化剂抗衰减性的影响，对细化剂重熔性能和重熔后细化性能的影响。

In the BPW,a brazing filler metal,which has high melting point and is able to dissolve the base metal significantly,is placed between the faying surface to be joined,the assembly is heated with high frequency induction heating,and a high uniaxial pressure is applied to discharge the molten interlayer ...

BPW新工艺以熔点较高并能显著溶解母材的钎料为中间层，利用感应电源加热并施加较大的压力，挤出液态中间层及氧化膜等形成的夹杂物，最终在焊接面周边形成圆滑过渡的钎角，同时，在界面处实现洁净母材之间直接接触的固相压力焊接合。

The results of its intrinsic fluorescence spectroscopy and fluorescence phase diagram showed that when the guanidine hydrochloride concentration in denaturation solution was about 1.0 mol/L, there existed a partially folded intermediate of Bacillus amyloliquefaciens a-amylase during its unfolding procedure, which followed a three-state model; the result of its fluorescence probe showed that when the guanidine hydrochloride concentration in denaturation solution was about 1.0 mol/L, there existed some stable hydrophobic regions, which could interact with a hydrophobic reagent 8-anilino-1-naphthalene sulfonic acid, in the partially folded intermediate of Bacillus amyloliquefaciens a-amylase; and the results of fluorescence quenching using acrylamide and potassium iodide as quenchers showed the distribution of Trp residues in Bacillus amyloliquefaciens a-amylase in different denaturation solution, with the maximum number (8) of tryptophan residues in a partially folded intermediate Bacillus amyloliquefaciens a-amylase molecule could be quenched by potassium iodide; and the results of their protein electrophoresis and SEC showed that no aggregate or aggregate precipitation of Bacillus amyloliquefaciens a-amylase formed during the whole unfolding procedure of Bacillus amyloliquefaciens a-amylase induced by guanidine hydrochloride.

内源荧光光谱和荧光相图结果表明，当变性液中盐酸胍浓度约为1.0 mol/L时，芽孢杆菌a-淀粉酶的去折叠过程中出现一个部分折叠中间体，其去折叠过程符合&三态模型&；荧光探针结果表明，在溶液中盐酸胍浓度约为1.0 mol/L时，中间态芽孢杆菌a-淀粉酶分子中存在着能够与探针分子1-苯胺基-8-萘磺酸结合的稳定的疏水区域；荧光猝灭研究给出了不同程度变性的淀粉液化芽孢杆菌a-淀粉酶中的Trp的分布情况，结果表明中间态芽孢杆菌a-淀粉酶分子中能够被碘化钾猝灭的位于分子表面的色氨酸残基数目达到最大的8个；蛋白电泳和体积排阻色谱结果表明，在盐酸胍诱导的芽孢杆菌a-淀粉酶分子的整个去折叠过程中，不会以共价键或非共价键形式形成芽孢杆菌a-淀粉酶分子之间的集聚体或集聚体沉淀。

And the wings of the cherubim were spread out so that the wing of the one cherub was touching the wall and the wing of the second cherub was touching the second wall; and their other wings were touching at the middle of the house, wing to wing.

6：27 他将两个基路伯安在内殿中间；基路伯的翅膀是张开的，这基路伯的一个翅膀触着这边的墙，第二个基路伯的一个翅膀触着那边的墙，里边的两个翅膀在殿中间彼此相触。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐