中轴的

Nowadays, the common application of compensation devices is an externally commutated thyristor inventor.

目前，在国内外船舶中，主要采用可控硅逆变器式的轴带发电机。

The results show that the microsphere located in a certain zone of focused laser optical electromagnetic fields will be trapped, and the trapping force deceases with the increase of the distance of the observed point away from the axis.

结果表明：位于聚焦光场中特定位置的微球可被俘获，当离轴距离增加，俘获力减小。

Results three different CT patterns were observed,a target lesion,a reniform mass,a sausage shaped mass,with a lower attenuation centrally,representing the intussuscepted mesentery.

结果 10 例CT扫描均可见多层靶环形、肾形或香肠形软组织影，中央部为脂肪和血管轴面影。2 例淋巴瘤多处可见肿大融合的淋巴结及肠壁不规则增厚，肠腔内造影剂充盈不均，1 例术中发现肠系膜过长而引起Tret's 韧带疝。

The CNC machined tubes are machined and lathed with extremely tight tolerances to hold the focuser and lens cell in precise alignment The tubes have internal light baffles spaced by aluminum rods for precise positioning to avoid vignetting during medium format photography and when using wide field 2 eyepieces.

镜桶及附属装置以 CNC 被机器制造而且与精密又稳定地支持其中的透镜组装置。在精确的对光中光轴已经为精确的定位，被铝竿隔开避免在使用观测摄影中被移位。

It was found that the cracks occurred around the silts in the loading process. For wall bears the constrained axial force which is generated by expansion of concrete, a lot of small cracks were distributed in wall.

结果表明：竖缝剪力墙在加载过程中，首先在竖缝附近发生开裂，主要分布在缝间墙上，并以细小裂缝为主，这是由于竖缝剪力墙承担了自身开裂膨胀而产生的约束轴力。

Methods The right median and ulnar nerves were transected at the axillary level for activation of Schwann cells in 20 SD rats, with their left median and ulnar nerves as control group.

近年来 ，在周围神经组织工程的研究中因作为种子细胞而颇受重视，大量的研究表明雪旺细胞在轴突再生中起重要的作用。

Based on the simulation data, the effects of clearances, damping coefficient and the rotation speed on the dynamic behaviors are studied: compared with ideal mechanisms, mechanisms with clearances are less stable; as for mechanisms with clearances, when the crank rotates at the speed of 100rad/s, the actual clearances are always above the radium of clearances, axle pin and axle cover keep contact throught the rotation; when the crank rotates at the speed of 20rad/s, mechanisms are in an unstable state, at an angle of about 300, the actual clearances are below the radium of clearances, pairs lose contact, which results in collision between them; with the speed of 20rad/s, when damping coefficient is assumed 175Ns/m, distinct separation and collision happen between pairs; when damping coefficient is assumed 220Ns/m, separation and collision are controlled.

在含间隙机构中，当曲柄以100rad/s转动时，运动副间隙始终大於半径间隙，轴销与轴套始终保持连续接触；当曲柄以低速20rad/s转动时，系统处於极不稳定的震荡状态，在转至300°左右时，运动副间隙小於半径间隙，脱离接触，发生明显的分离碰撞现象。在含间隙机构中，曲柄以低速20rad/s转动，当取法向阻尼系数为175Ns/m时，副元素发生明显的分离碰撞现象；当取法向阻尼系数为220Ns/m时控制了副元素的分离，副元素一直处於连续接触状态。

Chain so that axle shaft hole-side up there will be a new chain from the hole to put in.

使车轴链条有轴孔端朝上，将新链条的一头从孔中向里放。

The causes of the rolling flaws such as concavity on the end of workpiece、Mannesmann effect、spiral roll mark on the axle head and tooth roll mark etc in the lab-simulated experiment are analyzed to provide suggestion for the application of the CWR forming process of gear-shaft.

同时分析了物理实验过程中轧件各种质量缺陷的产生机制，如端头凹心、曼乃斯曼效应、轴端螺旋状压痕以及齿部齿条压痕等，为齿轮轴楔横轧成形工艺实用化研究提供指导。

The horizontal roll axial shifting is the important method for H beam mill to adjust roll gap and control the size accuracy of the finished product.

水平辊轴向移动是H型钢轧机进行辊缝调整、控制产品尺寸精度的重要方法，已广泛应用在H型钢轧机中，研究其结构及控制原理对于自主开发H型钢轧机具有重要意义。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。