中轴的

Shafting parts are widely used in mechanical products.

轴系零件是机械产品中的通用零件，应用较为广泛。

A steering angle of an elevator sheave on a shaft is adjusted at installation and subsequently during maintenance by one of several embodiments.

可通过若干实施例中的一个实施例在安装过程中和安装后的维修过程中对电梯滑轮在轴上的转向角进行调整。

If the region in is rotated through one revolution about the x-axis, find the volume of the solid of revolution.

d 若 中的区域绕 x 轴旋转一圈，求所得旋转体之体积。

Leaves crowded near apex of the trunk, spirally arranged; stipes dark brown, with sharp spines; lamina large, oblong, tripinnate; pinnae 17-20 pairs, alternate, longest one to 60 cm long, the basal one reduced; rachis short-spiny; pinnules 18-20 pairs, sessile or nearly so, lanceolate, to 10 cm long and 2.5 cm wide, divided almost to the costa; segments more or less falcate, toothed.

叶螺旋状排列，聚生於茎端；叶柄棕色，具锐刺；叶片大，长矩圆形，三回羽状深裂；羽片17-20对，互生，最大的长达60厘米，基部一对缩短，羽轴有短刺；小羽片18-20对，无柄或近於无柄，披针形，长达10厘米，宽2.5厘米，深裂几达中脉；末回裂片多少镰状，有齿。

But the symmetric axis of TI formation is parallel to the borehole axis in the thesis, the propagation velocity of SV-wave and SH-wave are the same in vertical direction, we can't see the splitting phenomena of shear wave.

本文中地层对称轴和井轴平行，SV波和SH波在竖直方向上的传播速度是相同的，本文地层模型下的井孔中是观测不到横波劈裂现象的。

However, in these cases, it may be more economical to use one or more larger diameter Bio-Module shafts mounted in concrete tankage Figure No.

但是，这种情况下，将一个或更大直径的生物模块轴安装在水泥池中会更节省成本。

A Bio-Clarifier shaft is supplied to be installed in concrete tankage.

生物二沉池的轴安装在水泥池中。

Check pressure and capacity of shaft seal water termly during operation.

运转中定期检查轴封水的压力和流量。

The pressure fluctuations were measured at different positions along the axial direction on the tonge. The coherence analysis was utilized for illustrating the blade passing frequency cancellation mechanism. A 3-D flow visualization method, which overcame the blind slight from LDV and PTV, was used to present the differences of internal flow patterns.

实验中分别进行0度、5度与10度三种叶轮扭转角之设计，在横流扇出风口以声学人偶进行噪音量测，评估不同叶轮扭转角在操作转速下之风扇噪音、并分析其声音品质；另外在舌端上不同的轴向位置撷取其压力扰动频谱进行相干性分析，探讨舌端上因不同叶轮扭转角对周期性压力扰动之破坏之探讨。

The paper analyses computer aided arithmetic about bending moment and torsional moment calculate of shaft parts which with any forces,and checking computations it with example.

分析了在任意不同作用力作用下轴类零件计算机辅助设计计算中弯矩、扭矩的计算机辅助算法，并以实例进行了验

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。