中轴的

Either of two quadric surfaces generated by rotating a hyperbola about either of its main axes and having a finite center with certain plane sections that are hyperbolas and others that are ellipses or circles.

双曲面两个二次曲面的任何一个，通过使一个双曲线绕其任何一根中轴旋转而成，而且旋转时有一个有一定双曲线平面切面的中心，而其他切面是椭圆或圆周

Either of two quadric surfaces generated by rotating a hyperbola about either of its main ax es and having a finite center with certain plane sections that are hyperbolas and others that are ellipses or circles.

双曲面两个二次曲面的任何一个，通过使一个双曲线绕其任何一根中轴旋转而成，而且旋转时有一个有一定双曲线平面切面的中心，而其他切面是椭圆或圆周

Nevertheless, given its fundamental flaws of overemphasizing ethics and lacking the system resource, it can' t be a ready plan of resolving the social and political problems of modern China.

但由于其存在着以伦理为中轴、制度性资源太少的根本性缺陷，不能作为解决当今社会政治问题的现成方案。

The inner spindle protrudesfrom the gear-box and contians a means for mounting various types ofchucks ,face plats ,and dog plates on it .

变速箱中突出的内轴含有接口，可连接各种型号的卡盘，面盘，狗盘。不是搞这个的，没有功劳还有苦劳

Shimano also claims the oversized axle and wider bearing spacing makes the whole assembly considerably stiffer than before.

Shimano同时声明超大尺寸的中轴和轴承间距是整个组合的强度与以前相比提高了。

The new technologies adopted in the design of φ1830mm 25 0mm dryer bearing assembly such as cone journal, CARB bearing, heat insulation sleeve and oil lubrication are introduced and the principle of lowering bearing temperature is discussed.

介绍在φ1830mm×6250mm烘缸轴承装置设计中采用的新技术，如锥颈轴、CARB轴承、隔热套、稀油润滑，同时探讨了降低轴承温度的原理。

Using simple boundary condition, the temperature gradient along the z direction is a constant while the generative internal heat is not considered.

仅从顶表面耗散热量的情况下，不考虑对辐射的吸收，晶体中轴向温度梯度为恒值。

The research indicates that when the gusset plate connections to slotted tubes member is used in practice, the rigidity of the member must be strengthened to avoid the happening of the whole buckling failure, and the combination of welded hollow spherical joints and gusset plate connection to slotted tubes member proves to be effective.

实际工程中应用管板连接构件作为受压构件时，必须加强构件弱轴的刚度，以避免整体失稳破坏，而采用焊接空心球补强是一种有效的方法。

Numerical simulation of chip removal during the cutting process is carried out for the average feeds determined during machine tool axis move- ment, since tooth marks are greatly affected by feed.

数值模拟芯片去除切削过程中进行的平均供稿期间确定机床轴动精神的，因为牙齿标志是大大受到饲料。

The corrosion resistance of 0Cr17Ni4Cu4Nb martensite precipitation hardening stainless steel used as high strength output shaft in artificial seawater was studied in this paper.

本文研究了用于制作高强度输出轴的材料0Cr17Ni4Cu4Nb马氏体沉淀硬化不锈钢在人工海水中的耐腐蚀性能。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。