中轴

To show this issue, can imagine a coordinate, the x-axis of coordinate states economy increases rate, cross axle represents the economic scale of one country, in coordinate.

为了说明这个问题，可以设想一个坐标，坐标的纵轴表示经济增长速度，横轴表示一国的经济规模，坐标中的。。。

Based on characteristic of chinese handwritten signature, some programs are developed to acquire the dynamic handwritten signature data from WACOM Tablet and to calculate velocities from acquired dynamic data. Based on statistics theory, instantaneous velocity and average X velocity and average Y velocity and time when the first maximal velocity arriving during on-line handwritten signa...

根据汉字手写签名的特点，编程从手写板获取签名的动态数据，编写了提取手写签名多种速度特征值的程序，在统计的基础上，对手写签名过程中的瞬时速度、X轴向平均速度和Y轴向平均速度、最大速度出现的位置、极大速度首次出现的位置等特征量的稳定性进行了实验研究，得出了一些有用的结论。

High density stacking faults are induced into Al-Co-Ni decagonal quasicrystal by using high temperature deformation. It is found that their fault planes are perpendicular to the ten-fold axis and their displacement vectors R are lying in the fault planes and parallel to a two-fold axis A2D.

通过高温形变的手段在Al-Co-Ni十次准晶中引入了高密度的层错，并发现这些层错的层错面与十次轴垂直，层错的滑移矢量R在层错面内并与二次轴A2D平行。

It is clearly shown that the Al-Ni-Rh decagonal quasicrystal with 1.6 nm periodicity contains a kind of atom columnar cluster with about 1.6 nm periodicity as the most fundamental structural building block.

主要的研究结果可以总结如下：1利用高分辨电子显微技术在Al_(75)Ni_(15)Rh_(10)合金中发现了1.6 nm周期的十次准晶，报道了这种准晶在二次轴方向及在十次轴方向的高分辨结构，阐述了其周期及其准周期的排列方式。

Because of the particularity of claw pole structure, the axial magnetic field produced by the stator winding is transformed into the diametric one along the circle of air gap.

当定子绕组通电时，电机中产生轴向磁通，爪极的作用就是将定子绕组产生的轴向磁场转化为沿气隙圆周径向排列的磁场，同时将 1对极转化为 P对极[1] 。

Multiple linear regression analysis of the data showed that vitreous length was the main factor to affected the formation and development of myopia diopter.

眼轴增长是近视眼发生、发展的重要因素，尤其对中、高度近视眼作用更为显著；眼轴长度的增长基本为玻璃体腔的延长。

Firstly, the projects of designation and improvement of prewatering pelletizer are demonstrated, including the structure, the ways of delivering the motivation and drawknife system by referring some improvement experience from production practice; Secondly, based on the analytical results, axial force, the torque and power are computed so that the electromotor, decelerator and other corresponding components could be determined; Thirdly, according to the parameters of the parts which has already been assured, the simple exercise diagram of the transmission device is analyzed and drawn up and the ratios of all levels are assigned.

参考实践生产中的一些改进经验，首先进行了总体方案的论证；然后根据分析的结果来计算各传动轴的轴向力、扭矩以及功率，并校核了轴和螺栓的强度，从而选择电机和减速机型号及设计其他相关零部件。

A person can place a drill in the drill chuck that is secured in the spindle of the drill press. They can then select the desired speed for rotation (commonly by switching belt pulleys), and activate the spindle. Then they manually pull on the quill lever to drive the drill into the workpiece being machined.

操作者可以将钻钻头装在钻夹中，钻夹固定在台钻的轴里；接着可以选择所需的转速（通常通过切换皮带改变主轴转速），并且启动主轴旋转，然后操作钻轴手柄，将钻头钻入被加工的工件。

The shorter or shortest axis of an ellipse or ''.

椭圆的较短的轴或椭球中最短的轴。

The results showed that, all the treatments can shorten the time of epicotyl germination of 'Fengdan', the 28 days chilling treatment was the shortest, and the next was 21 days chilling treatment and 300 mg/L GA3 treatment; in a certain range of GA3 concentrations, higher concentrations, higher seed germination index and germination rate in 'Fengdan'; the seed germination index and germination rate of 'Fengdan' after different time chilling treatments were higher than the control, in which, the treatment of 21 days chilling had the highest germination index and germination rate.

研究了不同时间的低温(4℃)处理及不同浓度的GA3处理对凤丹种子上胚轴萌发及幼苗生长的影响，结果表明：所有处理均能缩短凤丹种子上胚轴萌发时间，以低温28天处理初萌期最短，其次是低温21天和300mg/L GA3处理；在一定的GA3浓度范围内，浓度越高，凤丹种子发芽指数与发芽率越高；不同时间低温处理后凤丹种子发芽指数与发芽率均高于时照，其中低温21天处理是所有处理中发芽指数与发芽率最高的。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。