中杆

The characteristic of tied-arch bridge is a no-thrust arch structure by tensing the tied bar formin.

中承式系杆拱桥是拱桥家族中的一员，它的特点是靠系杆承受拱脚推力，是一种无推力的自平衡体系。

Through Hilbert transform, a signal's plane trace can be get. There are two frequencies in the tested signal, so the signal's plane trace may be looked as the track of the out pole's end when two poles rotate around parallel axles. Using the knowledge of motion synthesis in theory mechanics, a formula to describing the change of plane trace's step length and angle for two-frequency be get. So we may prolongate the tested signal's plane trace from the echo's initial arriving moment, and get a certain length of the signal's prolongation.

通过Hilbert变换可得到测试信号的平面迹线，测试信号中只含有两个频率成分，视为双频信号，双频信号的平面迹线相当于两连杆绕平行轴转动时外杆杆端迹线，利用理论力学中运动合成和瞬心知识，推导出双频信号平面迹线步长平方满足余弦线性复合函数，而迹线转角可视为线性变化，据此可对回波到来之前的测试信号平面迹线作延长，得到一定长度的信号延展段，信号延展段与实测段作差可得到一次、二次回波的第一个波峰值。

The Original Superstrong once again received the 'Best for Value stamp' this time from Golf Monthly magazine in it's August test of mid-priced forged clubs.

标准型的Superstrong锻造铁杆这次又在Golf Monthly杂志八月份的中价位锻造铁杆测试中获得〝最佳价值标章〞。

Little tremie grouting,systemic rock bolt and horizontal prestressed rock bolt are the most effective reinforcing technique s which have been validated in practice.

而小导管注浆、系统锚杆及水平贯通预应力锚杆是应用最为广泛的3种中夹岩加固技术，并在实践工程中得到有效验证。

Zhou Xunshu overcame a slow start — bogeys on two of his first three holes — to finish with a 1-under 71 in the opening round of the RMB 1 million (US$146,681) Dell Championship Thursday at Orient Golf Club in Xiamen, the first event on the 2009 Omega China Tour.

周训书在克服了开始时的一些不顺后—在前三洞中吞下两个柏忌—最后以71杆低于标准杆一杆的成绩结束了首轮的比赛，这场星期四开始在东方高尔夫俱乐部举办的戴尔锦标赛是2009欧米茄中巡赛的首场赛事，总奖金为人民币一佰万元(约合美金146，681)。

Research results show that when the frequency of excitation signal is within 10kHz to 100kHz the wave in free bolt and grouted rockbolt is guided wave which is related to its boundary conditions. Waves with different frequencies have different velocities.

研究结果显示在测试激发波的频率范围内(10~100 kHz)，锚杆中传播的波是一个和边界条件相关的导波，不同频率的波在锚杆中传播的速度不同。

Products factory operators; Steyr, Steyr Wang, Hao Wo main bridge shell rear axle, bearing blocks, cross the bridge cover, Steyr wheel shell, shift cylinder, rear axle sudden yuan, ZF Clutch fork shaft, swing rod, before and after the brake hub, Steyr various separation fork, gear room covered ,67-68 pulley, bridge sudden yuan, steel plate, parallel to shell axis, double-H shift shaft , 0503 Steyr-axis between the shell bad, bad Steyr 0198 Inter-axis shell, oil seal and seat, steel plate before and after the hanging ears, rear wheel, shift box assembly, double H shift rocker, one, two block I. block F99588, shift box casing, drive shaft telescopic forks, steel slide, shift cylinder, a variety of connecting plates, gearbox sudden yuan, three, blockIntroduction F99589, Steyr cylinder cover, double-H shift dial head, adjust the lever fork, wheel cover, FL clutch fork, FL Clutch fork shaft, Steyr after the output shaft bearing support, flywheel shell, fork and seat connection, Steyr Cylinder Head,ácover ,67-68 water pipe joints, rear brake camshaft bracket, rear axle minus the main shell, minus the shell of the main bridge, bearing seat, adjust the lever forks, brackets, brake lane joystick arm, gearbox sudden yuan, clutch pedal arm, oil block at the end of care, single head, double-headed rocker, gear room covered, decelerationround, adjust the lever forks, shift box casing, double H shift dial head, Double H shell, gear room covered, separation lever plate before and after the hanging ears, double-H shift shaft, decelerationround,áBushing, Steyr 10 file clutch shell, the bridge box, minus the shell after the main bridge , Bearing Block, the bridge cover, Steyr wheel shell, shift cylinder, after the sudden the bridge element, ZF Clutch fork shaft, swing rod, steel slide, shift box casing series products .

本厂经营产品；斯太尔，斯太尔王，豪沃后桥主桥壳，轴承座，过桥箱盖，斯太尔轮边壳，换挡汽缸，后桥突元，ZF离合器拨叉轴，摆杆，前后制动毂，斯太尔各种分离拨叉，齿轮室盖，67-68皮带轮，中桥突元，钢板垫板，平行轴壳，双H换挡轴，斯太尔0503轴间差壳，斯太尔0198轴间差壳，油封及座，钢板前后吊耳，后轮毂，换挡盒总成，双H换挡摇臂，一，二挡导块F99588，换挡盒套管，传动轴伸缩叉，钢板滑座，换档汽缸，各种连接盘，变速箱突元，三，四挡导块F99589，斯太尔汽缸盖，双H换挡拨头，杠杆调整叉，轮边盖板，FL离合器拨叉，FL离合器拨叉轴，斯太尔输出轴后轴承座，飞轮壳，连接叉及座，斯太尔汽缸盖（欧II，平衡轴盖板，67-68水管接头，后制动凸轮轴支架，后桥主减壳，中桥主减壳，轴承座，杠杆调整叉，托架，行车制动操纵杆臂，变速箱突元，离合器踏板臂，油底托块，单头，双头摇臂，齿轮室盖，减速轮垫片，杠杆调整叉，换挡盒套管，双H换挡拨头，双H壳体，齿轮室盖，分离杠杆，钢板前后吊耳，双H换挡轴，减速轮垫片，平衡轴衬套，斯太尔10档离合器壳，过桥箱，后桥主减壳，轴承座，过桥箱盖，斯太尔轮边壳，换挡汽缸，后桥突元，ZF离合器拨叉轴，摆杆，钢板滑座，换挡盒套管等系列产品。

The results show that it is technically feasible to apply the turning fixture and the feeding device of the pump rod joint to the pump rod joint production. In the actual production process, one person can control many lathes to realize the production and the whole system also demonstrates excellent and safe performance in the operation process.

结果表明，抽油杆接箍车削上料装置用于抽油杆接箍生产在技术上是可行的，在实际生产过程中可以实现一人控制多台机床进行生产，整套系统在运行过程中也表现出极好的运行性能和安全性能。

Providing the specific problems which enterprises encounter in their actual production processes, the problems in the development of enterprises are effectively resolved. Therefore it is essential to introduce latest technologies. The turning fixture and the feeding device of the pump rod joint can be used to realize the automatic discharging. With engine lathes transformed into computerized numerical control and pneumatic tailstocks coordinating revolving centers to use, partial automation production of pump rod joints can be realized.

为了切实解决企业发展中遇到的问题，可利用抽油杆接箍车削上料装置实现自动出料，通过普通车床的数控化改造和气动尾座的配合活顶尖的使用，可以实现抽油杆接箍的半自动化生产，以解决企业在生产过程中遇到的问题。

The compositions of fatty acids in mid-gut gland of cultured healthy Penaeus monodon, healthy Penaeus japonicus, P. monodon slightly infected by MBV, P. monodon severely infected by MBV and P.

应用气相色谱法分别检测了人工养殖的健康斑节对虾、健康日本对虾、斑节对虾杆状病毒轻度感染斑节对虾、MBV重度感染斑节对虾及患中肠腺坏死杆状病毒病日本对虾中肠腺脂肪酸的组成及含量。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐