不适应性 - 网络例句 - 英语人，englisher

Because mechanical finger's outflow boundary change has the limitation, this kind of jig may clamp the work piece which takes also correspondingly to have the similar surface, simultaneously as a result of mechanical finger's quantity which installs is limited, but the jig itself does not replace, finger's outflow boundary change was not also big, causes the capture strength not to have the very big compatibility.

由于机械手指的外缘变化具有局限性，这种夹具可以夹取的工件也相应的必须具有类似的表面，同时由于安装的机械手指的数量有限，而夹具本身并不替换，手指的外缘也变化不大，导致了抓取力也不具有很大的适应性。

Then, we design a disturbance observer and adaptive control in the acceleration feedback loop to compensate the influence of disturbance and estimate the variation of inertia and viscous damping constant respectively.

并且希望内回路干扰影响与J、B变动影响尽可能降低，故在加速度内回路设计干扰估测器与适应性控制，使得外部位置回路不受干扰与J、B变动影响，提高系统之精度。

It possesses the merit of steam drying kiln and dehumidification drying as well as avoids the demerit of no steaming and low temperature of dehumidification drying.

它兼有蒸汽干燥适应性广和除湿干燥节能的优点避免了除湿干燥不能喷蒸、干燥温度低的缺点。

It possesses the merit of steam drying kiln and dehumidification drying as the same time avoid the demerit of no steaming and low temperature of dehumidification drying.

它兼有蒸汽干燥适应性广和除湿干燥节能的优点避免了除湿干燥不能喷蒸、干燥温度低的缺点。

"Angoras require a dry climate but are otherwise hardy, and thrive under semi- arid conditions where sheep do not prove a complete success."

安哥拉羊需要干燥的气候，但除此之外，它的适应性是很强的。在半干旱条件下，养绵羊不会很成功，但安哥拉羊却能长得很好。

Unlike most carnivores, hyenas are born in an advanced state of development.

不同于大多数食肉，适应性出生在一个先进的发展状态。

The writer thinks existing major problems:1、The confusion Produces by the same plant have the different name、the different plant have the same name、think the typeface meaning just the righteousness,even fabricate without basis etc; 2、Because dont understand living creature type and adaptability in the depth of the water for the plants , A great deal of aquatic plants death;3、In planting design, so much express of plants specification ,and many of them are disobey with biology characteristic, so the plants are hard for purchase or the result is very bad after plant; 4、Plant density more than 100 times or less than several decuples of normal.

作者认为存在的主要问题有：1、植物名称同物异名、同名异物、望文成义，甚至凭空捏造等等产生的混乱；2、植物生物型和水深适应性不了解造成的种植水深不符植物习性，从而使大量水生植物死亡；3、种植设计中，苗木规格的表述不妥，许多表述与植物的生物学特性相违背，造成苗木难以采购或种植后效果极差；4、种植密度严重偏大或偏小，偏大的大于正常的100多倍，小的则少几十倍。

The writer thinks existing major problems:1、The confusion Produces by the same plant have the different name、the different plant have the same name、think the typeface meaning just the righteousness,even fabricate without basis etc; 2、Because dont understand living creature type and adaptability in the depth of the water for the plants , A great deal of aquatic plants death;3、In planting design, so much express of plants specification ,and many of them are disobey with biology characteristic, so the plants are hard for purchase or the result is very bad after plant; 4、Plant density more than 100 times or less than several decuples of normal.

作者认为存在的主要问题有：1、植物名称同物异名、同名异物、望文成义，甚至凭空捏造等等产生的混乱；2、植物生物型和水深适应性不了解造成的种植水深不符植物习性，从而使大量水生植物死亡；3、种植设计中，苗木规格的表述不妥，许多表述与植物的生物学特性相违背，造成苗木难以采购或种植后效果极差；4、种植密度严重偏大或偏小，偏大的大于正常的100多倍，小的则少几十倍检针机。

The writer thinks existing major problems:1、The confusion Produces by the same plant have the different name、the different plant have the same name、think the typeface meaning just the righteousness,even fabricate without basis etc; 2、Because dont understand living creature type and adaptability in the depth of the water for the plants , A great deal of aquatic plants death;3、In planting design, so much express of plants specification ,and many of them are disobey with biology characteristic, so the plants are hard for purchase or the result is very bad after plant; 4、Plant density more than 100 times or less than several decuples of normal.

作者认为存在的主要问题有：1、植物名称同物异名、同名异物、望文成义，甚至凭空捏造等等产生的混乱；2、植物生物型和水深适应性不了解造成的种植水深不符植物习性，从而使大量水生植物死亡；3、种植设计中，苗木规格的表述不妥，许多表述与植物的生物学特性相违背，造成苗木难以采购或种植后效果极差；4、种植密度严重偏大或偏小，偏大的大于正常的100多倍，小的则少几十倍螺旋板换热器。

The simulation results of the cylinder-block model were given in the article, consistent with that of Middlemen"s. It was shown that the block part could improve the uniformity of the flow distribution. The analysis of the flow field of some materials with different power-law factor in the die designed by Mckelvey was close to that of Mckelvey"s. It was shown that the flow distribution was uniform in the die that can producesheets with 1200mm in width. During the analysis the flow channel was divided into several parts to get the details about the fluid flow in each area. A conclusion was drawn after analyzing the influence of the die pressure on the flow distribution, that the higher pressure is good for the output and bad for the uniformity of the distribution. Simulation of the die applying the cylindrical main runner showed the fact that when the cylinder replaced the cone the change of uniformity was trivial. The uniformity of the non-block flow channel was so poor that the block in the proper position of the die channel was necessary. The project of the die for the wider sheet was put forth, and the analysis of the fluid flow in the die was shown.

本文模拟了圆柱管缝隙流模型的三维流动场，得到了与Middlemen结论一致的流动均匀性，并通过模拟直观地展示了采用阻尼块可以改善挤出均匀性的现象；分析了多种幂率指数的流体在Mckelvey等人设计的流道模型中的流动分布，得到了与Mckelvey的分析结果接近的压力降和流量偏差；本文建立了1200mm幅宽机头流道的三维有限元模型，并逐个分析各个区域和多个截面的流动分布状况，由此揭示了1200mm幅宽L-型机头流道内的流北京化工大学硕士学位论文动分布基本均匀，并在分析了机头压力对于挤出流动分布的影响后得出结论：较高的机头压力可以获得较大的产量，但是不利于物料均匀分布；模拟了采用圆柱管主流道时机头流道内的流动分布，得出结论：主流道由圆锥管改为圆柱管时对流动均匀性影响不大，通过设置适当的阻尼仍然可以达到挤出平衡；模拟了两端进料式圆柱管无阻尼流道的流动均匀性后得到结论：两端进料式无阻尼结构的流动均匀性较差，宽机头中仍然有必要设置阻尼块；确定宽幅机头流道的基本方案，并设计了一种宽幅防水卷材挤出机头流道的结构，通过流动模拟表明该种结构的流动均匀性较好；考察了宽幅机头对于不同厚度片材的挤出适应性，得到结论：当生产不同厚度的片材时，阻尼块高度需要调整。