不能弯曲的

The results were found as following:(1) The damage value increases more significantly with the increase in PVF before 30% PVF, beyond which the increasing trend becomes gradually gentle.(2)Keeping the interphase strength and PVF unchanged, the damage increase with increasing moisture concentration in a nearly linear relation.(3)The results generated from the FCC model with consideration of the interphase debonding are in good agreement with the experimental data, meanwhile, the FCC model is also capable of predicting the critical load for the damaged and the undamaged dental composite subject too the 3-point flexural test.4 A 3D-fmite element analysis has been successfully exploited to examine the mechanical behavior of the restoration-tooth structure under the polymerization shrinkage and water sorption. It was found:(1) The low stiffness of the composite has the effect to limit the displacement occurring in the remaining tooth tissue. For lower interphase, the cuspal flexures are litter higher. The high interphase modulus acts as a \'shielding effect\' for stress transfer.

得到如下结论：(1)相同的吸湿性，在30％PVF(颗粒体积分数：Particle volume fraction，PVF)前增加PVF，层间脱胶损伤值显著增加；此后损伤值的增加趋于平缓；(2)保持层间强度和PVF不变，层间脱胶损伤随吸湿率的增加而接近线性增加；(3)FCC(面心立方：Face-centred cubic，FCC)模型层间脱胶损伤的预测结果和实验数据基本吻合；同时此模型可以用于预测牙齿填充材料三点弯曲实验的临界载荷。4、建立理想牙齿修复结构，利用有限元方法研究了同时考虑聚合收缩和吸湿膨胀耦合作用下的填充修复材料和粘结界面层材料性能对牙齿修复结构的力学行为的影响，得到如下结论：(1)低弹性模量的牙齿填充修复材料能限制天然牙组织的位移，但天然牙组织的位移与粘结界面层的弹性模量无关。

Of ⊥ of attentively of Tuo of predestined relationship of sew of be favored with of mother of adept of Bei of midge slave-girl lament includes a shoe 1 centimeter tall advisable, after sitting down, can make truncal weight is pressed in human body to be able to bear most on the hip of pressure and framework, make lower limbs exert oneself at whole sole, bipod shift is convenient also.

桌子：以身体竖立，两手掌平放在桌面上时关节不弯曲为宜，一般桌高75～80厘米。椅子：椅面距地面的高度以低于小腿高1厘米为宜，坐下后能够使躯干的重量压在人体最能承受压力的臀部和骨架上，使下肢着力于整个脚掌，两脚移动也方便。

The mechanism of instability wrinkling in the process based on minimum energy principle is revealed, uniform mathematic description of the wrinkling wave on the strip of in-plane bending is established, the internal and external energy is deduced by energy method, and a uniform criteria of internal and external wrinkling is established; then how to combine the criteria with the FEM simulation system to make the numerical prediction of wrinkling into reality is also resolved in the paper. The effects of the forming parameters on the deforming result are analyzed by the uniform predict criteria. The results show as follows: as the compress width increase, external wrinkling first come into being, then internal winkling do, and finally in-plane bend occur; the loading wedge angle increase, internal winkling first come into being, thenin-plane bend do, and finally external wrinkling occur; in-plane bend is possible to occur with a increase of the strain-hardening exponent and the strength coefficient; and the effect of the friction factor may be ignored.

2揭示了板带不均匀压下面内弯曲成形过程基于能量原理的失稳起皱机理，提出了统一的描述内外缘起皱波形的函数，采用变分法推导了服从该波形函数的内外缘起皱能，建立了统一的起皱预测准则；将新建立的统一的起皱预测准则引入到数值模拟系统IBS中，数值预测结果与实验结果的吻合较好；分析了成形过程各参数对起皱的影响规律：随着接触变形区宽度的逐渐增大，先是发生外缘起皱，然后发生内缘起皱，进而才出现稳定成形；随着实际加载楔角的增大，先是发生内缘起皱，然后发生稳定成形，进而出现外缘起皱；硬化指数和强化系数增大，易于稳定成形；摩擦因子对起皱的影响不明显；而且接触变形区宽度对起皱的影响最大。

They require no forming or bending, and can be shaped into numerous design variations: square corners for a crisp look; detents for plastic labeling, or offsets for EMI shielding strips or clips.

不需要变形或弯曲就能定型从而满足各种设计需求：明快的方角设计，塑料标签的定位装置，或组成防止电磁干扰部件的支架。

The intensity of NP peak of type-Ⅱ initailly increased with the increase of the excitation power and decreased thereafter. This is due to the electrons and the holes were localized in different space of typ-Ⅱ QW, then the band bending occurs when the carrier concentration increases with the power, NP peak shft to high energy. The electron transited to relaxed Si〓Ge〓 layer and combined with the localized holes radiatively.

型量子阱的NP峰随激发功率增加先增加后减小，这是由于在Ⅱ型量子阱中电子和空穴不在空间同一位置，较强激发功率下产生的高浓度载流子引起能带弯曲严重，NP峰向高能方向移动，到某一定程度时开始出现电子跃迁至弛豫Si〓Ge〓层与其中的空穴复合发光。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。