不垂直

This brush 10 has a curved core 11 to which the bristles are connected, and presents a section varying over at least a part of length of the brush in the geometrically non-similar form. The above section at least at one point of the core is asymmetric in relation to a plane perpendicular to the plane of curvature of the core in the above point.

本发明涉及一种刷子10，具有连接有刷毛的弯曲轴芯11，在刷子长度的至少一部分上具有变化的截面，且该变化方式在几何上是不相似的，位于轴芯的至少一点处的所述截面相对于垂直于所述点处轴芯的曲面的平面是不对称的。

Their motion asymmetry supported the idea of close correlation between motion perception symmetry and binocularity.

三位双上旋肌麻痹，一位视神经重度发育不全，一位早产儿网膜症，两位合并水平及垂直斜视，一位角膜彼得氏异常和一位网膜先天缺损，他们自出生起就没有发育双眼视觉的机会，他们不对称的运动觉支持了运动觉对称性和双眼视觉之间相关性的理论。

When the conditional symmetric instability lies in the middle level and conditional instability in the lower and upper levels, the circulation will have updrafts through the total column of the atmosphere. The release of conditional instability gives rise to a mesoscale rain belt.

当低层和高层出现条件不稳定，中间呈条件对称不稳定或弱稳定度层结时，从低层到高层出现较深厚的垂直上升气流，湿重力不稳定能量的释放导致了云带的形成。

The mechanism was similar to the equivalent barotropic warm core structure. The Conditional Instability of the Second Kind was the primary mechanism of development and maintenance for MCSs in case 2005. As the MCSs intensified and persisted, the latent heating was highly efficient in producing significant enhancement of Mei-Yu front systems. The LLJ intensified by Coriolis acceleration of ageostrophic wind was induced by the effect of latent heat release. The LLJ and the effect of latent heat released reinforce each other in convection system through a positive feedback process.

综合而言，2005年个案中梅雨锋面结构为垂直近乎不倾斜的浅系统，槽线系统不明显，锋面水平温度梯度微弱，低层具有强水平气旋式风切，较似正压系统，个案中MCS发展及维持机制，主要是透过CISK 过程来维持；其过程是由於低层锋面带上之辐合激发对流发展，对流潜热释放造成局部气压梯度增强，因而增强地转风；而潜热释放亦有利低层辐合之增强，产生非地转风，再透过科氏加速增强西南风，使LLJ增强，形成一正向的回馈作用。

In the design of the structure, a new 2-D scanning machine is put forward which has overcome the limit of common underwater TV system influenced by the environment of water. It can scan 360 degrees in horizontal plane and 90 degrees in vertical plane, and there isn't dead angle.

根据以上内容的研究和分析，在结构设计方面，提出了二维扫描机构，它克服了一般水下电视系统由于使用特殊环境的限制不能进行扫描的缺点，可以进行水平360度，垂直90度全方位扫描，并且不存在盲区。

At the time of dealing with the fourth problem, we try calculus of variation of spending, move route transform into a line issue of the victory, Utilize Euler formula , ask and publish time running orbit after a little while most , confirm right route most, It's a pity that we can't get a satisfactory answer in a short time.

得到如下结果：在水流速度不变的情况下，年第一名的游速为，与方向与X轴成，如竞渡者以行进，则与X轴成，用时分秒，竞渡者若与对岸垂直游不可能达到终点；在不同区段内水流速度不变的情况下，竞渡者以折线前进，用时约为；在同一区段内水流速度变化情况下，竞渡者以曲线前进，用时约为。

Adjust the related dimension for level and vertical direction with metal strip ruler and gradienter, request level error is no more than 1 mm / m , total error is no more than 3 mm.

使用钢带尺及水平仪校准框架水平及垂直方向的尺寸，要求水平误差不超过每米1毫米，总误差不超过3毫米。

Adjust the related dimension for level and vertical direction with metal strip ruler and gradienter, request levelerror is no more than 1 mm / m , total error is no more than 3 mm.

使用钢带尺及水平仪校准框架水平及垂直方向的尺寸，要求水平误差不超过每米1毫米，总误差不超过3毫米。

This process will be gilded, belling in operation is complete, the product has a fine gilding pepme up, left, beautiful, nonpressure the characteristics of the convex back pocket.

这栽工艺不兵烫金、压凹在一道工序上达不败，产物具有烫金颓丧、图文粗忽、丑观、无压凹垂直的特不背。

This paper analyses the advantages of down feed two pipe horizontal cascade system in all aspects and influencing degree by natural circulation pressure.

分析了下供下回水平双管系统的优点以及自然循环作用压力的影响程度，计算数据证明下供下回水平双管系统的垂直热力失调基本不存在；因为每层供回水采用双管系统，所以也不存在距离热源最远的散热器不热问题。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。