不同成分

The dynamic tensile test was carried out on five TWIP steels with strain rates in the range of 102 ~103S-1 by employing a pneumatic indirect bar-bar tensile impact tester, and the results was compared to the static tensile behavior.

采用气动式间接杆杆型冲击拉伸试验装置对5种不同成分的TWIP钢在102~103S-1应变速率范围内的动态拉伸变形行为进行了研究，并和静态拉伸性能作了比较。

The investigation of the solution treatment of hot-rolled TWIP steel of three different compositions (Fe-25Mn-4Si-2Al, Fe-30Mn-4Si-2Al and Fe-30Mn-3Si3Al) revealed that prolonging the temperature holding time can increase the elongation with no obvious change found in strength.

对3种不同成分的TWIP钢(Fe-25Mn-4Si-2Al， Fe-30Mn-4Si-2Al， Fe-30Mn-3Si-3Al)进行热轧后的热处理实验，结果表明，增加固溶处理的保温时间，可提高TWIP钢的延伸率，而强度的变化并不明显。

Ti, M carbonitrides considered as examples, the valence electron structure of solid solution with different compositions was calculated.

以为例计算了不同成分的固溶体的价电子结构。

The effects of alloy elements on the matrix of austenitic manganese steel and its behavior of work hardening were studied in this thesis, establishing the relations of valence electron parameter and macro-property.

本文研究了合金元素对不同成分锰钢基体的作用及其对加工硬化行为的影响，建立了微观价电子参数同宏观性能的联系。

The activities of Sb in nine Sn-Sb alloys at 923,1023 and 1123 K were determined by measurement of vapour pressure.

本文在自行研制的测定蒸气压装置上，测定了9个不同成分的Sn－Sb合金在923，1023，1123K时Sb的活度。

To test stainless steel wire rope with different compositions immerged in seawater and to analyze and discuss anti-corrosion property.

对不同成分的不锈钢丝绳进行海水全浸试验，对耐腐蚀性能进行分析和讨论。

In materials science there is also an emphasis on developing and using knowledge to understand how the properties of materials can be controllably designed by varying the compositions, structures, and the way in which the bulk and surfaces phase materials are processed.

材料科学也强调发展和利用知识来了解怎样使材料很好地控制并设计成各种不同成分、结构、对材料进行表面和相处理的方法。

The Ce and La particulates in mischmetal were dispersively distributed into the Mg melt before the formation of Al RE compound and may serve as substrate for heterogeneous nucleation with 0.05% mischmetal addition.

过热处理工艺对Mg Al系合金有明显的细化作用，但不同成分的合金所需的过热温度不一样，通常的过热温度在液相线温度以上 15 0℃到 2 6 0℃之间[1] 。

New fancy yarn spinning machine can Tatu yarn, Loop yarn, TT yarn, knot yarn, AB yarn, wrapped yarn, TT circle composite yarn; four-color gilling machine can be different components of the crude under mixing ratio to be a gradual change in color spinning color tops; small needle crochet machine filament or yarn can be used as raw material, imitation scallops hollow yarn, cut yarn, yarn hook chain; multifunction fancy spinning yarn spinning machine can core-spun yarn, thick yarn, the strength-twist yarn, slub yarn, etc..

新型花式纺纱机可以纺制大肚纱，圈圈纱， TT 纱，结子纱， AB 纱，包缠纱，圈圈 TT 复合纱等；四色针梳机可将不同成分的粗条根据比例来进行混条，纺制颜色渐进变化的彩色毛条；小针筒钩编机可以用长丝或纱线为原料，仿制空心带子纱，割毛纱，勾链纱等；多功能花式纺纱机可以纺制包芯纱，粗细纱，强弱捻纱，竹节纱等。

The cleaning efficiency of the Meros process depends on a number of operating conditions such as the concentration of various components of the raw gas, gas temperature, conditioning temperature, additive quantities, quality and type.

Meros系统的净化效率主要依赖于许多运行条件，例如原始气体中不同成分的浓度、气体的温度、调节器的温度、添加剂的数量、质量还有种类。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。